Summary of the content on the page No. 1
DIGITAL AUDIO MIXING CONSOLE
OXF-R3
[English]
OPERATION MANUAL
1st Edition (Revised 3)
Software Version 3.0 and Later
Summary of the content on the page No. 2
CAUTION For customers in Europe Installation has to be done by a SONY authorized This product with CE marking complies with both the EMC technician. Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European WARNING Community. To prevent fire or shock hazard, do not expose the unit to rain or moisture. Compliance with these directives implies conformity to the following European standards: To avoid electrical shock, do not open the cabinet. Refer •
Summary of the content on the page No. 3
Peak Inrush Current OXF-IO3000 (1) Mise sous tension (ON), méthode de sondage du OXF-CP3048PS courant: (1) Power ON, current probe method: 20A (100) 50A (100V) 70A (240V) 110A (240V) (2) Mesuré conformément à la norme européenne (2) Hot switching inrush current, measured in EN55103-1: accordance with European standard EN55103-1: 30A (230V) 40A (230V) OXF-SP3000 Spitzenstrom (1) Power ON, current probe method: OXF-CP3048PS 40A (100V) 80A (240V) (1) Einschaltstrom, Stromsonde: 50A (100V) (2) Hot s
Summary of the content on the page No. 4
OXF-CP3048PS only WARNING This unit has no power switch. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power cord to a socket-outlet which must be provided near the unit and easily accessible. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power cord. WARNUNG Dieses Gerät hat keinen Netzschalter. Beim Einbau des Geräts ist daher im Festkabel ei
Summary of the content on the page No. 5
Table of Contents About This Manual....................................................................................5 1-1 Overview ......................................................................................... 1-2 Chapter 1 1-2 Data Flow........................................................................................ 1-4 Overview 1-3 Signal Flow...................................................................................... 1-6 2-1 OXF-R3 Start-Up......................
Summary of the content on the page No. 6
Table of Contents 4-1 The Basic (Default) Signal Path ................................................... 4-2 Chapter 4 4-2 Stereo Mix-Down Signal Path with Processing Inserted ........... 4-4 Signal Paths 4-3 Mix-Down with Post Channel Fader Insert ................................ 4-6 4-4 Recording to a Multitrack ............................................................ 4-7 4-5 In-Line Channel Multitrack Recording Set-up .......................... 4-8 4-6 In-Line Channel with Insert Post Ch
Summary of the content on the page No. 7
6-2-8 Routing Panel ..................................................................... 6-28 Chapter 6 6-2-9 LCD Channel Screen Panel ............................................... 6-31 Technical Descriptions 6-2-10 Sends 1-24 Panel ................................................................ 6-32 6-3Central Section Panels.................................................6-38 6-3-1 Master Fader Panel ............................................................ 6-38 6-3-2 Monitor Panel.....
Summary of the content on the page No. 8
Table of Contents 7-6 The Session Management™ Screen Pages ................................. 7-27 Chapter 7 7-6-1 The Start-up Logo Screen .................................................. 7-27 Session Management™ 7-6-2 The System Screen ............................................................. 7-28 7-6-3 The Machines Screen ......................................................... 7-30 7-6-4 Artists/Projects & Titles Screen ......................................... 7-32 7-6-5 Mixes & Cues
Summary of the content on the page No. 9
About This Manual Purpose and intended readers Chapter 6 Technical Descriptions This is the operation manual for the OXF-R3 digital Provides the descriptions of all the modules of the audio mixing console. It explains how to use the OXF-R3, including the names, locations and functions OXF-R3 to record, mix and output digital audio of the controls. This chapter also includes descriptions signals. of the associated SP Rack and I/O Rack system. This manual is aimed at professionals such as Chapte
Summary of the content on the page No. 10
About This Manual Conventions used in this manual This manual uses the following conventions: Chapter 3, Section 10 • Subsection 5 • within Section 10 Operation • Step number • Cross-reference within the manual Important note 6 About This Manual
Summary of the content on the page No. 11
Related manuals In addition to this operation manual, the following manuals are available for the OXF-R3: • Installation Manual • Service Manual About This Manual 7
Summary of the content on the page No. 12
About This Manual Glossary of Terms ABS Absolute O/B Outside Broadcast ADC Analogue to Digital Converter O/L Overload AES Audio Engineering Society AFL After Fader Listen PAN Panoramic ATR Audio Tape Recorder PCB Printed Circuit Board AUX Auxiliary PCM Pulse Code Modulation PFL Pre Fader Listen CAL Calibrated or Calibration PSU Power Supply Unit CH Channel CMRR Common Mode Rejection Ratio RET Return CR Control Room RSL Remote Studio Link DAC Digital to Analogue Converter S-C Side Chain DAT Digit
Summary of the content on the page No. 13
Chapter 1 Overview Chapter 1 – Overview This chapter introduces the OXF-R3 digital audio mixing console and describes the main features. An example system configuration and a signal flow diagram are included. Chapter 1 Contents 1-1 Overview ......................................................................................... 1-2 1-2 Data Flow ........................................................................................ 1-4 1-3 Signal Flow ........................................
Summary of the content on the page No. 14
Chapter 1 Overview 1-1 Overview 1-1 Overview The OXF-R3 is a ‘high end’ digital audio mixing console system. It comprises four main components: • Control Console with Modular Control Surface • Host Computer • Signal Processing (SP) Rack • Digital and Analogue I/O Racks The following illustration shows a basic system concept diagram. 21 5 43 System Concept diagram 1 SP Rack 4 Digital and Analogue I/O Racks 2 Host Computer 5 Control Console 3 Multitrack Tape Recorder(s) 1-2 Chapter 1 Overvie
Summary of the content on the page No. 15
Chapter 1 Overview Control Console Compared with traditional console designs, the OXF-R3 offers greater flexibility within more compact dimensions by using an assignable control surface. Modular Control Surface The control surface of the OXF-R3 makes extensive use of assignable panels to provide a console of manageable size for either one or two operators, whilst giving greatly increased functionality. The current system is capable of controlling up to 96 full channels and 12 stereo return cha
Summary of the content on the page No. 16
Chapter 1 Overview R (RC) 1-1 Overview 1-2 Data Flow 1 2 C AUTOMATION MEDIA SUB HOST COMPUTER CR MONITORS 1 CONTROL FOR SP AUDIO PROCESSING & MACHINES MODEM SYSTEM STATUS & DISPLAY DATA CR MONITORS 2 SP RACK MADI CR MONITORS 3 4 SURROUND L SURROUND R FX RACK MADI 2 TRACK ANALOGUE AUDIO AUDIO I/O RACK GPI AUDIO Sample installation illustrating Audio & Control Data flow 1 Control Room 2 Rack Room 1-4 Chapter 1 Overview (LC) L
Summary of the content on the page No. 17
Chapter 1 Overview 3 RECORD REHEARSE CUE LISTEN STUDIO L/S GPI FOLDBACK AUDIO AUDIO AUDIO I/O RACK GAIN MADI FS MADI TC FS OUT SYNCHRONISER TC MOTIONWORKER PROTOCOL MOTIONWORKER MASTER TC PCM-3348 48 TRACK GPI I/O RECORD REMOTES & TALLIES RACK TC TRANSPORT 9P TRANSPORT 9P TC TRANSPORT 9P TRANSPORT 9P TC TC PCM-7050 PCM-7050 PCM-7050 PCM-9000 MASTERDISC DAT DAT DAT AES/EBU AES/EBU AES/EBU AES/EBU TIME CODE CONTROL DATA AUDIO DATA 3 Studio 4 Machine Room Chapter 1 Overview 1-5
Summary of the content on the page No. 18
Chapter 1 Overview 1-1 Overview 1-3 Signal Flow SELECTOR 1 SELECTORS 2-7 SELECTOR 8 MAIN ST. OUTPUT BYPASS LCRS BUS FILTERS 5.1 Ø SUPER MIC SEND GPs 5 BAND EQ 7.1 1-16 DYNAMICS ST M/T M/T Ø INSERT LCRS BUSSES 5.1 1-48 DELAY FX 7.1 UP 48 M/T FADER SENDS & TO 8 LINE Ø STEMS RETURNS MULTITRACK FUTURE SP CUE & AUXILIARY SENDS 1-24 CHs 1-48 SELECTOR 1 SELECTORS 2-7 SELECTOR 8 MAIN ST. OUTPUT BYPASS LCRS BUS FILTERS 5.1 Ø SUPER MIC SEND GPs 5 BAND EQ 7.1 1-16 DYNAMICS ST M/T M/T INSERT Ø LCRS BUSSES
Summary of the content on the page No. 19
Chapter 1 Overview EXTERNAL SOURCES 1-8 8 X STEREO MONITOR LS 1 INPUTS MAIN CONTROL ROOM MONITOR LS EXTERNAL SOURCES 9-12 4 X 8 WIDE SURROUND MONITOR INPUTS LS 2 CONTROL ROOM MONITOR LS SOLO LS 3 MONITOR LS AFL STUDIO LS 1 PFL STUDIO LS 2 TALKBACK FOLDBACK 1 LISTEN MIC 1 FOLDBACK 2 FOLDBACK 3 FOLDBACK 4 TALKBACK 1 Chapter 1 Overview 1-7 MAIN OUTPUT BUS - STEREO, LCRS, 5.1 or 7.1 16 SUPER SEND GROUPS - MONO, STEREO, LCR, LCRS, 5.0, 5.1, 7.0 & 7.1 48 MULTITRACK BUSSES - Up to 8 MULTI-CHANNEL STE
Summary of the content on the page No. 20
