Summary of the content on the page No. 1
FA-101_e.book 1 ページ ２００５年１１月２４日 木曜日 午後１時２５分
Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES” (p. 3–p. 5). These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new
unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a
convenient
Summary of the content on the page No. 2
FA-101_e.book 2 ページ ２００５年１１月２４日 木曜日 午後１時２５分 For the U.K. IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. BLUE: NEUTRAL BROWN: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN m
Summary of the content on the page No. 3
FA-101_e.book 3 ページ ２００５年１１月２４日 木曜日 午後１時２５分 USING THE UNIT SAFELY The symbol alerts the user to important instructions Used for instructions intended to alert or warnings.The specific meaning of the symbol is the user to the risk of death or severe determined by the design contained within the injury should the unit be used triangle. In the case of the symbol at left, it is used for improperly. general cautions, warnings, or alerts to danger. Use
Summary of the content on the page No. 4
FA-101_e.book 4 ページ ２００５年１１月２４日 木曜日 午後１時２５分 012b 101b • Immediately turn the power off, remove the AC • The unit and the AC adaptor should be located so adaptor from the outlet, and request servicing by their location or position does not interfere with your retailer, the nearest Roland Service Center, or their proper ventilation. an authorized Roland distributor, as listed on the ..................................................................
Summary of the content on the page No. 5
FA-101_e.book 5 ページ ２００５年１１月２４日 木曜日 午後１時２５分 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 3, please read and observe the following: Power Supply Maintenance 301 401a • Do not connect this unit to same electrical outlet that is • For everyday cleaning wipe the unit with a soft, dry cloth being used by an electrical appliance that is controlled by or one that has been slightly dampened with water. To an inverte
Summary of the content on the page No. 6
FA-101_e.book 6 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Handling CD-ROMs 204 * Microsoft and Windows are registered trademarks of 801 Microsoft Corporation. • Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty CD-ROM 206e discs may not be read properly. Keep your discs clean * The screen shots in this document are used in compliance using a commercially available CD cleaner. with the guidelines of the Microsoft Corporation. 206j * Wind
Summary of the content on the page No. 7
FA-101_e.book 7 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Contents Contents of the package ......................................................... 8 Front and rear panel ................................................................ 9 Front panel ............................................................................................................................9 Rear panel..................................................................................................................
Summary of the content on the page No. 8
FA-101_e.book 8 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Contents of the package ■ FA-101 fig.FA-101 ■ AC adaptor This is the dedicated AC adaptor for the FA-101. Use only the supplied AC adaptor. ■ FireWire (IEEE 1394) cables (one 6-pin ↔ 6-pin cable, one 6-pin ↔ 4-pin cable) Use one of these cables to connect the FA-101 to the IEEE 1394 connector (FireWire connector, iLink connector, DV connector) of your computer. The 6-pin ↔ 4-pin cable cannot supply bus power. * Use only the F
Summary of the content on the page No. 9
Phone plug (unbalanced) FA-101_e.book 9 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Front and rear panel Front panel fig.front 15 1 3 4 4 56 10 11 13 78 9 12 14 16 2 fig.jack-type 1. Combo input jacks These are analog audio input jacks with mic preamps. They accommodate either XLR or phone plugs, allowing you to connect a variety of equipment. Either balanced or unbalanced signals may be connected. XLR plug Phantom power (48 V) is provided for XLR type connections, allowing you to conne
Summary of the content on the page No. 10
FA-101_e.book 10 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Front and rear panel fig.front 15 1 3 4 4 56 10 11 13 78 9 12 14 16 2 4. Input/output level indicators These LEDs light according to the level of the signals that are being input via the combo input jacks (1) and WAVE OUT 1/2 (in the case of WDM, OUTPUT 1 ➔ see p. 22). (see block diagram ➔ front cover) To adjust the input level, stop playback of the sound from your computer. The red LED wi
Summary of the content on the page No. 11
FA-101_e.book 11 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Front and rear panel 9. Sample rate select switch This specifies the sampling frequency at which audio data will be recorded and played back. In order to get this setting to take effect, you must exit all of your software, then cycle the power to the FA-101 (switch it off, then back on again). * If you are using Macintosh and want to change the sampling frequency, you must first power dow
Summary of the content on the page No. 12
FA-101_e.book 12 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Front and rear panel Rear panel fig.rear 17 18 19 20 24 25 26 21 22 23 17. Power switch Used to switch the power on (DC IN) or off (OFF), and for switching to bus power (BUS). fig.power-sw BUS Bus power can be used if the FA-101 is connected to your computer via a FireWire (IEEE 1394) cable. In this case, power is supplied from your computer via the FireWire (IEEE 1394) cable. If you want to use bus power, set the power switch
Summary of the content on the page No. 13
FA-101_e.book 13 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Front and rear panel 20. Grounding terminal Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that the surface feels gritty to the touch when you touch this device, microphones connected to it, or the metal portions of other objects, such as guitars. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are
Summary of the content on the page No. 14
FA-101_e.book 14 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Macintosh) 1 With the FA-101 disconnected, start up your Macintosh. Once the connections have 2 Use a FireWire (IEEE 1394) cable to connect the FA-101 to your Macintosh. been completed, turn on 1. With the FA-101’s power switch off, connect the power cord to it. power to your various devices in the order 2. Plug the AC adaptor cable into an AC outlet. specified. By turnin
Summary of the content on the page No. 15
FA-101_e.book 15 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Macintosh) * Depending on the model of Macintosh you are using, starting up the Macintosh when the FA-101 is connected may cause operation to become unstable. In this case, start up the Macintosh and then connect the FA-101. * If you want to change the FA-101’s sample rate, turn the FA-101 off, change the sample rate, and then turn the FA-101 on again. If, in the Mac OS Sy
Summary of the content on the page No. 16
FA-101_e.book 16 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Macintosh) Checking that you hear sound Now, let’s play back the sample data to verify that the connections and settings are correct. We will use iTunes to play back the sample data provided on the included CD- ROM. Use of the song data Before you continue, connect headphones or monitor speakers to the FA-101 as described in “Basic connections” (p. 25). supplied with this product for any purpos
Summary of the content on the page No. 17
FA-101_e.book 17 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Windows) What is a driver? A driver is software that allows data to be transferred between the FA-101 and application software running on your computer when the FA-101 is connected to your computer via a FireWire (IEEE 1394) cable. The driver sends data from your application software to the FA-101, and from the FA- 101 to your application software. The driver is r
Summary of the content on the page No. 18
FA-101_e.book 18 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Windows) 8 From the Windows start menu, choose “Run...” Checking the name of The “Run” dialog box will appear. your drive. 9 Input the name into the dialog box as shown, and click [OK]. From the start menu, fig.win-run choose My Computer. In the window that appears, verify the name of the CD- ROM drive into which you inserted the CD-ROM in step 7. The (D:) or (E:) displaye
Summary of the content on the page No. 19
FA-101_e.book 19 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Windows) 14 A dialog box entitled “Completing the Found New Hardware Wizard” appears. If the Found New Click [Finish]. Hardware Wizard asks Once again, the “Found New Hardware” message appears near the taskbar. Please wait. you whether you want to connect to Windows 15 Update, choose “No” and A dialog box entitled Welcome to the Found New Hardware Wizard appears. Make
Summary of the content on the page No. 20
FA-101_e.book 20 ページ ２００５年１１月２４日 木曜日 午後１時２５分 Installing the driver (Windows) If you changed the “Driver Signing Options” setting (p. 17, step 4), restore the setting to its previous state after restarting Windows. 1. Log on to Windows using the same user account as the one used when the driver was installed. 2. From the Windows start menu, choose Control Panel. 3. In “Pick a category,” click Performance and Maintenance. 4. In “or Pick a Control Panel icon,” click the System icon. The Sys
