Summary of the content on the page No. 1
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Cheetah PCI Adapter Introduction Accton’s Cheetah PCI Adapter is a dual-speed Fast Ethernet card for PCI local bus compliant computers. A true plug-and- play device, this card is auto-configurable upon power up and also supports auto-negotiation to automatically select the optimum speed and communication mode of an attached device. Additionally, the Cheetah PCI Adapter complies with ACPI, Wired for Management 2.0, and PC99, and includes support for Remote Wake-Up by Magic Packet™. Package Checkl
Summary of the content on the page No. 4
Quick Installation Guide LED Indicators The following table describes the operation of the Cheetah PCI Adapter status LEDs: LED Status Description
! "
# # ! " $
% & "% " ' * ) '( " %+ ( ' ( ) , - Installation
Summary of the content on the page No. 5
Cheetah PCI Adapter 4. Connect the Cheetah PCI Adapter directly to a 10BASE-T or 100BASE-TX hub or switch using UTP cable (Category 3, 4 or 5 for 10BASE-T; Category 5 for 100BASE-TX). The maximum allowable length of UTP cable connections is 100 meters (328 ft.). When inserting an RJ-45 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. 5. Replace the computer’s cover and power it on. The Cheetah PCI Adapter should be automatically configured by the host
Summary of the content on the page No. 6
Quick Installation Guide 2. Select the “View Current Configuration” option from the Main Menu to access the screen shown below. If you wish to modify the current configuration, return to the Main Menu and select “Setup New Configuration.” 3. The host computer’s BIOS automatically allocates the necessary resources, such as the Interrupt and I/O Base, to the Cheetah PCI Adapter. Although the Setup Program will not allow you to change those resources, you can change the settings displayed on the “S
Summary of the content on the page No. 7
Cheetah PCI Adapter 4. In the event of a problem with the Cheetah PCI Adapter, use the Setup Program to run the card’s built-in diagnostics (see the “SET1207D.TXT” file for specific instructions). Should any of the diagnostic tests fail, reboot your computer and run the diagnostics again to see if the problem persists. If it does, record the failure indicated and contact Accton’s Technical Support for assistance. 5
Summary of the content on the page No. 8
Quick Installation Guide Troubleshooting Check the following troubleshooting items before contacting Accton Technical Support. PCI Compatibility Some PCI computers are not self-configuring and require you to perform some or all of the following functions by motherboard jumper changes and/or BIOS Setup program configuration: Make sure your BIOS correctly supports the PCI Local Bus Specification v2.0 or later and upgrade your computer BIOS to the latest version. Verify that the PCI slot is an
Summary of the content on the page No. 9
Cheetah PCI Adapter Adapter Installation Problems If your computer can’t find the Cheetah PCI Adapter or the network driver doesn’t install correctly, check the following: Make sure the adapter is securely seated in the PCI slot. Check for any hardware problems, such as physical damage to the card’s edge connector. Try the card in another PCI bus-master slot. If all fails, test with another Cheetah PCI Adapter that is known to operate correctly. Check for resource conflict in the PCI conf
Summary of the content on the page No. 10
Quick Installation Guide Compliances FCC Class B Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
!
Summary of the content on the page No. 11
Cheetah PCI Adapter VCCI Class B Compliance (Japan) CE Mark Declaration of Conformance This is to certify that this product complies with ISO/IEC Guide 22 and EN45014. It conforms to the following specifications: EMC: EN55022(1988)/CISPR-22(1985) class B IEC 1000-4-2(1995) 4kV CD, 8kV AD IEC 1000-4-3(1995) 3V/m IEC 1000-4-4(1995) 1kV - (power line) IEC 1000-4-6(1995) 3Vrms This product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/ EEC, and c
Summary of the content on the page No. 12
Quick Installation Guide Specifications General Specifications . /#
)%(0, -,+ 12
$
*+ 3 ))%(0,4 -,+ 12
$
3 5
#
*6, ,
# #78% %
# #.%
#8(# 9 :05#
); : / )); : /%
) 1*6 * 3
, ) < 1 + += 3
" )> =)>1 , 3
Summary of the content on the page No. 13
Cheetah PCI Adapter 11
Summary of the content on the page No. 14
Warranty Accton warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for the lifetime of the product. For the warranty to apply, you must register your purchase by returning the registration card indicating the date of purchase and including proof of purchase. There will be a minimal charge to replace consumable components, such as fuses, power transformers, and mechanical cooling devices. The warranty does not cover the
