Summary of the content on the page No. 1
USB 2.0 Gigabit Network Adapter
Model # AGIGAUSB
User’s Manual
Ver. 1A
Summary of the content on the page No. 2
Table of Contents Introduction ..................................................................................................................... 4 Package Contents ....................................................................................................... 4 Specifications .............................................................................................................. 4 Network Specification.......................................................................
Summary of the content on the page No. 3
REGULATORY STATEMENTS FCC Certification Part15, Class B The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. FCC Part 15 Registration This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interface, and • This device must accept any interface received, including interface th
Summary of the content on the page No. 4
Introduction The USB 2.0 Gigabit Network Adapter (hereafter referred to as the Gigabit Adapter) is specifically designed to plug into any available Universal Serial Bus port of a desktop or laptop PC. The Gigabit Adapter is for users who wish to connect to a 10Mbps, 100Mbps or 1000Mbps Fast Ethernet LAN using the convenience and ease of USB technology. The Gigabit Adapter complies with USB Specification 1.0/1.1/2.0. It uses an USB type B connector to connect directly to the USB host co
Summary of the content on the page No. 5
100Mbps: Appears as solid orange when the device is connected to 100Mbps network; blinking orange when transmitting data. Gigabit: Appears as solid green, when the device is connected to Gigabit network; blinking green when transmitting data. Power Requirement Operating Voltage: 5V DC Operation Mode: 425mA (Max) Physical specification Dimension: 3.2"(L) x 2.2"(W) x1" (H) EMC Certification • FCC Part15 ClassB • CE • VCCI
Summary of the content on the page No. 6
Installation The following steps and screen shots are for Windows XP. Steps for Windows 2000 are similar unless noted otherwise. Note: Do not connect the USB 2.0 Gigabit Network Adapter to your computer until you’ve reached the appointed step. If the Gigabit Adapter is connected already, Windows will detect the Adapter and request for a driver. Click Cancel to quit the wizard and remove the Gigabit Adapter from your computer. Step 1 Insert the Driver CD into your CD drive and wait f
Summary of the content on the page No. 7
Step 3 Click Next at the welcome screen. Step 4 Click Next to accept the default destination location for the driver to be installed in or click Browse to select the desired location. 7
Summary of the content on the page No. 8
Step 5 Click Next to accept the Program Folder for the driver. Step 6 Click Continue Anyway at the Windows Logo Testing prompt. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). 8
Summary of the content on the page No. 9
Step 7 Click Finish to complete the installation wizard. Step 8 Connect one end of the Gigabit Network Adapter to your computer’s USB port and connect the other end to a hub/switch/router. Step 9 At the Found New Hardware Wizard window, select No, not this time and click Next. 9
Summary of the content on the page No. 10
Step 10 Select Install the software automatically (Recommended) and click Next. For Windows 2000, select Search for a suitable driver for my device (Recommended) and click Next. Then check on the CD-ROM drives check box and click Next. Step 11 Click Continue Anyway at the Windows Logo Testing prompt. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). 10
Summary of the content on the page No. 11
Step 12 Click Finish to complete the installation. Step 13 Restart your computer to activate the Gigabit Network Adapter. 11
Summary of the content on the page No. 12
Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on My Computer from your desktop and select Properties. Step 2 Select the Hardware tab and click on Device Manager. 12
Summary of the content on the page No. 13
Step 3 Expand Network adapters from the list and verify that 10/100 Gigabit USB2.0 Network Adapter is listed and no yellow question mark is beside it. Congratulations! You have successfully installed the USB 2.0 Gigabit Network Adapter. 13
Summary of the content on the page No. 14
Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Actual throughput will vary. Network conditions and environmental factors lower actual throughput rate. Copyright © 2005 AirLink101. All rights reserved. AirLink101, the stylized AirLink101 logo, specific product designations, and all other words and logos that are identified as trademarks and/or service marks
