Summary of the content on the page No. 1
®
Dialogic DSI SS7MD Network
Interface Boards
Programmer’s Manual
www.dialogic.com
Summary of the content on the page No. 2
Copyright© 2009 Dialogic Corporation. All Rights Reserved. You may not reproduce this document in whole or in part without permission in writing from Dialogic Corporation at the address provided below. All contents of this document are furnished for informational use only and are subject to change without notice and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries ("Dialogic"). Reasonable effort is made to ensure the accuracy of the information contained in
Summary of the content on the page No. 3
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 Contents 1 Introduction ............................................................................................................. 7 1.1 Related Information ............................................................................................ 7 2 Specification ............................................................................................................. 9 2.1 Product Identifiers ............................................
Summary of the content on the page No. 4
Contents 4.8.3 Dynamic Operation .................................................................................37 4.8.4 Example Code for Building and Sending MVD_MSG_SC_LISTEN Message........37 4.8.5 Interconnecting LIUs using STREAM_XCON ................................................38 4.9 Received Message Timestamping .........................................................................39 4.9.1 Host Configuration ........................................................................
Summary of the content on the page No. 5
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 Figures 1 Switch Connections...................................................................................................36 2 Drop and Insert........................................................................................................38 3 Protocol Configuration Message Sequence Diagram .....................................................179 4 Q.SAAL Configuration Message Sequence Diagram...........................................
Summary of the content on the page No. 6
Contents Revision History Date Part Number Issue Description July 2009 05-2640-003 3 Description of thermal sensor operation added. Support for introduction of ATM termination mode and May 2009 05-2640-002 2 timestamping. April 2009 05-2640-001 1 Supports the first production release. Note: The current issue of this guide can be found at: http://www.dialogic.com/support/helpweb/signaling 6
Summary of the content on the page No. 7
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 Chapter 1: Introduction ® Dialogic DSI SS7MD Network Interface Boards are specialized T1/E1/J1 SS7 signaling boards suitable for ® use in PCI Express form factor systems. The boards use the common Dialogic DSI software API to the application that enables applications to be easily ported. ® The boards provide a hardware platform to enable running Dialogic DSI Protocol Stacks for the realization of Signaling System Number 7 signaling nodes. In
Summary of the content on the page No. 8
1 Introduction 8
Summary of the content on the page No. 9
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 Chapter 2: Specification This chapter provides information about: � Product Identifiers ® � Dialogic DSI SS7MDL4 Network Interface Board - Low Profile PCI Express Form Factor � Software Licenses 9
Summary of the content on the page No. 10
2 Specification 2.1 Product Identifiers ® The Dialogic DSI SS7MD Network Interface Board product family includes the PCI Express form factor described in the following subsections. ® 2.1.1 Dialogic DSI SS7MDL4 Network Interface Board - Low Profile PCI Express Form Factor Product DSI SS7MDL4 PCI Express form factor product line includes the following: � DSI SS7MDL440Q A low profile PCI Express form factor with 4 T1/E1/J1 ports, supporting up to 124 SS7 links, up to 4 SS7 HSL links, up to 128
Summary of the content on the page No. 11
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 ® 2.2 Dialogic DSI SS7MDL4 Network Interface Board - Low Profile PCI Express Form Factor The DSI SS7MDL4 board is a x1 lane electrical, x4 lane physical, low profile PCI Express form factor, which can be installed in x4, x8, or x16 lane slots. The board is supplied with two End Brackets suitable for low profile and full height installation. Features of the DSI SS7MDL4 board are described in the following topics: � Capacity � Host Interface �
Summary of the content on the page No. 12
2 Specification which to install the board. Refer to Section 2.2.7, “Airflow Requirements” on page 13 for more information. 2.2.3 Physical Interfaces The DSI SS7MDL4 board supports the following physical interfaces: � Four T1/E1/J1/J1 digital trunk interfaces. See Section 2.2.3.1 below for more detail. 2.2.3.1 T1/E1/J1 Digital Trunk Interface Properties The properties of the T1/E1/J1 digital trunk interfaces are described as follows: � Standard — Four interfaces each are software configurabl
Summary of the content on the page No. 13
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 2.2.5 Visual Indicators The DSI SS7MDL4 board includes the following visual indicators: � T1/E1/J1 dual-color Green/Red status LEDs: — Green indicates a valid link — Red indicates a line alarm Note: Only the LEDs 0, 1, 2, and 3 are active (LEDs 4, 5, 6, and 7 are reserved for future use). 2.2.6 Power Requirements Power requirements are described as follows: � +12 VDC power 1.1 A typical, 1.4 A max. � Power dissipation 17 W max. 2.2.7 Airflow R
Summary of the content on the page No. 14
2 Specification 2.2.9 Safety, EMC and Telecommunications Specifications Safety, EMC and telecommunications specification information is provided by the following: ® � Dialogic DSI SS7MDL440Q Network Interface Board Regulatory Notices Supplied with each product and provides a full list of the specifications to which DSI SS7MDL4 board conforms. � International Declaration of Conformity See http://www.dialogic.com/declarations. � Country-Specific Approvals See the Global Product Approvals list
Summary of the content on the page No. 15
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 2.3 Software Licenses The DSI SS7MDL4 codefile supports different MTP2 link densities on the board. These are enabled using a Host Software License that is to be ordered at the same time as the hardware. The Host Software License licenses a specific number of link resources on the host that may be shared between boards in the same chassis. For details on how to activate the host license please refer to Dialogic® DSI Protocol Stacks - Host Licen
Summary of the content on the page No. 16
2 Specification The following combinations of link types are available to the user: Run Mode LSL Links HSL Links ATM Links IMA Links LSL Y Y Y HSL YYY ATM YYY IMA Y Y Note: When using multiple link types on the same board, the run mode indicates to the board the predominant link type. Note: To change the run mode of a board, the board must be reset. 16
Summary of the content on the page No. 17
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 Chapter 3: Installation This chapter contains the following topics: � Software Packages � Software Installation for Linux � Software Installation for Solaris (SPARC) 17
Summary of the content on the page No. 18
3 Installation 3.1 Software Packages This manual describes the installation and use of the following software: � Development Package � User Part Development Package ® � Binary for Dialogic DSI SS7MD Network Interface Boards 3.1.1 Development Package Different variants of the Development Package are available for the supported operating systems. Each Development Package contains: � a device driver � library functions and header files for use by an application � a number of executables to b
Summary of the content on the page No. 19
® Dialogic DSI SS7MD Programmer’s Manual Issue 3 3.2 Software Installation for Linux The Development Package for Linux is distributed as a download from the Dialogic web site. See Section 1.1, “Related Information” on page 7. The distribution is in the form of a single compressed file called dpklnx6.Z. Installation of the software is described in more detail in the following topics: � Installing the Development Package for Linux � Installing the DSI SS7MD Source Device Driver � Support for a
Summary of the content on the page No. 20
3 Installation The ldconfig utility creates a symbolic link to the GCT library shared object within the install directory. For example: /opt/dpklnx: libgctlib.so.1 -> libgctlib.so.1.0.1 If the installation machine is to be used to build applications, an additional link must be created from libgctlib.so.1 to libgct.so: ln -s libgctlib.so.1 libgct.so 3.2.2 Installing the DSI SS7MD Source Device Driver The DSI SS7MD device driver source build and installation scripts are in the Development Pac
