Summary of the content on the page No. 1
FUJITSU PCI GigabitEthernet 3.0 Update1
TM
for Solaris Operating System
User's Guide
Summary of the content on the page No. 2
For Safe Operation Handling of This Manual This manual contains important information regarding the use and handling of this product. Read this manual thoroughly. Pay special attention to the section "Important Warnings". Use the product according to the instructions and information available in this manual. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering from damages to their property. Use the product according to this manual. Documen
Summary of the content on the page No. 3
Revision History Revised section (*1) Edition Date Details (Added/Deleted/Altered) 01 2003-2-20 - - Appendix D PRIMEPOWER1/100 is added 3.4 Change the procedure 02 2003-5-1 3.3.1 Some parameter explanations are added 3.5 Some procedures are added 3.6 VLAN information is added 03 2004-1-8 - Change the Version 2.0 to 2.1 Appendix E VLAN tested switches are added Chapter 4 LinkAggregation function is added - Change the Version 2.1 to 2.2 04 2004-10-28 Appendix A Messages are add
Summary of the content on the page No. 4
Preface Purpose This manual describes how to install the FUJITSU PCI GigabitEthernet card in your PRIMEPOWER system, and configure the environment setting of the interface. Target Reader This book is intended for system administrators responsible for installing the FUJITSU PCI GigabitEthernet card. To understand the concepts and procedures presented in this manual, you need from one to two years of experience in the Solaris (TM) Operating System (in this document, abbreviated to Solari
Summary of the content on the page No. 5
iv
Summary of the content on the page No. 6
Contents Chapter 1 Product Outline.......................................................................1 1.1 Key Features.................................................................................2 1.2 GigabitEthernet card Specifications..........................................................3 1.2.1 Specifications...........................................................................3 1.2.2 Part Names and Features of Hardware............................................
Summary of the content on the page No. 7
Contents Appendix C Using GigabitEthernet in a Cluster Environment.......................................71 C.1 Cluster Environment Support.................................................................71 C.2 Cluster Environment Setup Procedure.........................................................71 C.3 Notes.......................................................................................72 Appendix D PCI Slot Number and Device Name............................................
Summary of the content on the page No. 8
Chapter 1 Product Outline The following topics are described in this chapter. ● Key Features ● GigabitEthernet card Specifications
Summary of the content on the page No. 9
Chapter 1 Product Outline 1.1 Key Features The FUJITSU GigabitEthernet card is a adapter designed for Solaris OS servers that are connected to a GigabitEthernet network. This card offers the physical services and data link services defined by IEEE802.3. Table 1.1 GigabitEthernet function Main Function IEEE802.3 compliant 1000Base-SX(PW008GE4, PW0G8GE1), 1000Base-SX * 2ports(SE0X7GD2X), 10/100/1000Base-T(PW008GE5, PW0G8GE2, PRIMEPOWER250/450 secondary LAN ), 10/100/1000 Base-T * 2port
Summary of the content on the page No. 10
1.2 GigabitEthernet card Specifications 1.2 GigabitEthernet card Specifications The FUJITSU PCI GigabitEthernet card is an adapter that is installed into a PCI slot or a PCI Express slot. 1.2.1 Specifications The specification of the FUJITSU PCI GigabitEthernet adapter is listed in "Table 1.2.1 PCI GigabitEthernet Card Specification" and "Table 1.2.2 PCI Express GigabitEthernet Card Specification". Table 1.2.1 PCI GigabitEthernet Card Specification Item Compatibility Host Bus Interfa
Summary of the content on the page No. 11
Chapter 1 Product Outline connection is not supported. ● When using 1000Mbps transfer rate with PW008GE5, PW0G8GE2, PRIMEPOWER250/450 secondary LAN port, SE0X7GD1X, PW008QG1 and SE0X7GQ1X, only Auto-Negotiation=On can be used. 1.2.2 Part Names and Features of Hardware Figure 1.1 to 1.8 shows the appearance of the FUJITSU PCI GigabitEthernet adapters. The part names and features are listed as follows. Connection: PW008GE4, PW0G8GE1 and SE0X7GD2X allow optical fibre cable connection, PW
Summary of the content on the page No. 12
1.2 GigabitEthernet card Specifications Figure 1.1 1000Base-SX Figure 1.2 10/100/1000Base-T (PW008GE4) (PW008GE5) Figure 1.3 1000Base-SX Figure 1.4 10/100/1000Base-T (PW0G8GE1) (PW0G8GE2) 5
Summary of the content on the page No. 13
Chapter 1 Product Outline Figure 1.5 1000Base-SX * 2ports Figure 1.6 10/100/1000Base-T * 2ports (SE0X7GD2X) (SE0X7GD1X) 6
Summary of the content on the page No. 14
1.2 GigabitEthernet card Specifications Figure 1.7 10/100/1000Base-T * 4ports Figure 1.8 10/100/1000Base-T * 4ports (PW0G8GE1) (SE0X7GQ1X) 7
Summary of the content on the page No. 15
Summary of the content on the page No. 16
Chapter 2 Installing FUJITSU PCI GigabitEthernet Card This chapter describes the tasks necessary to install this card in the main unit. ● Installation of the GigabitEthernet card ● Identifying the GigabitEthernet card ● Cable connection
Summary of the content on the page No. 17
Chapter 2 Installing FUJITSU PCI GigabitEthernet Card 2.1 Installation of the GigabitEthernet Card Insert the card in a PCI slot or a PCI Express slot on the main unit. (Please refer to the main unit’s User’s Manual for details about installing cards and specific PCI slot or PCI Express slot specifications.) 10
Summary of the content on the page No. 18
2.2 Identifying the GigabitEthernet Card 2.2 Identifying the GigabitEthernet Card The GigabitEthernet card can be identified by executing the "boot -r" command at the OpenBoot prompt. ok boot -r 11
Summary of the content on the page No. 19
Chapter 2 Installing FUJITSU PCI GigabitEthernet Card 2.3 Cable Connection To connect the PW008GE4, PW0G8GE1 and SE0X7GD2X GigabitEthernet card to the network, use an optical fiber cable. To connect the PW008GE5, PW0G8GE2, PRIMEPOWR250/450 secondary LAN, PW008QG1, SE0X7GD1X and SE0x7GQ1X GigabitEthernet card to the network, use a CAT5E twisted pair cable (Enhanced Category 5). Figure 2.3.1 PW008GE4 (with Optical Fiber Cable) 12
Summary of the content on the page No. 20
2.3 Cable Connection Figure 2.3.2 PW008GE5 (with Twisted Pair Cat5E Cable) 13
