Summary of the content on the page No. 1
H-DS20L
USB 2.0 Docking Station
Summary of the content on the page No. 2
FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communication
Summary of the content on the page No. 3
Basic Overview……………………………………………………………………...…….4 Safety Instructions………………………………………………………………...4 Introduction……………………………………………………………………….4 Features…………………………………………………………………………...4 System Requirements……………………………………………………………..5 Package Contents…………………………………………………………………5 Supported Operating Systems…………………………………………………….5 Technical Specifications…………………………………………………………………..6 Hardware Installation…………………………………………………………………..…7 Software Installation……………
Summary of the content on the page No. 4
SAFETY INSTRUCTIONS 1. Always read the safety instructions carefully. 2. Keep this User’s Manual for future reference. 3. Keep this equipment away from humid environments. 4. Lay this equipment on a reliable, flat surface before setting it up. 5. If any of the following situations arise, have the equipment checked by a service personnel: The equipment has been exposed to moisture The equipment has been dropped and/or damaged The equipment has obvious signs of breakage The
Summary of the content on the page No. 5
SYSTEM REQUIREMENTS PC or Mac MS Windows 98SE, ME, 2000, XP & Mac OS9.x & 10.1 Available USB Port 64 MB RAM or above Pentium 233 MHz or higher PACKAGE CONTENTS Docking Station – 1pc DC5V Power supply - 1pc User’s Manual - 1pc Software driver CD-ROM - 1pc Type-A to Type-B USB Cable - 1pc SUPPORTED OPERATING SYSTEMS Windows 98SE, ME, 2000, XP Mac OS 9.x and OS 10.1 5
Summary of the content on the page No. 6
Type Docking Station With LAN Computer Port 1 upstream port Type B receptacle 2 USB 2.0 downstream ports, Type A receptacle I/O Ports 1 PS/2 Keyboard port Mini Din 6-pin 1 PS/2 Mouse port Mini Din 6-pin 1 File Transfer port Type B receptacle 1 serial port DB 9-pin male 1 parallel port DB 25-pin female 1 10/100M LAN port 8P8C RJ-45 shielding Emission CE, FCC Power AC Input 100 V~240V DC Output 5V, 2.5A Environments Operating temperature: 0C~70C Storage temperature: -40
Summary of the content on the page No. 7
LED Status Indicators Once the USB Port Replicator is connected, the Hub Link LED is lit green and the LAN LED is lit after the Ethernet cable is connected. Type # of LEDs Color Descriptions Docking 1 Red The AC to DC power adapter is plugged Station w/ into the power port LAN 2 Green When any of the hub ports, which are connected to USB devices, are activated. 2 Green The LED for your Ethernet LAN port is to indicate 10/100 Mbps speed. Figure 1. USB Port Replicator P
Summary of the content on the page No. 8
Figure 2. Upstream Port and Power Connector Connect to power adaptor Connect to PC (I) Connect the power adapter and plug it into the back of the docking station. Find an unused electrical outlet and plug it in the power adapter. Plug the flat end (A plug) of the USB cable into a free USB port on your PC. Plug the square end (B plug) of the USB cable into the USB upstream connector located on the back of the docking station. At th
Summary of the content on the page No. 9
1. Two-Port Hub Before you connect a USB device to one of the Hub ports, please follow the software installation instructions provided in the subsequent pages of this User’s Manual. 2. PS/2 ports (Keyboard and Mouse port) If you connect a PS/2 keyboard or mouse to the docking station and you are using a PC, you will not need the software driver. However, if you are using a Mac, you will need to install the software driver on the CD-ROM onto your computer. The software drivers
Summary of the content on the page No. 10
Installation for Windows 98SE & ME 1. The H-DS20L Install wizard searches for new drivers. Click Next to continue. 2. Select "Search for the best driver for your device [Recommended]," and click Next to continue. 10
Summary of the content on the page No. 11
3. Select "CD-ROM drive", and click Next to continue. 4. Windows will now search for the driver file for the device. Click Next to continue. 11
Summary of the content on the page No. 12
5. Windows has finished installing the software. Click Finish to end the Wizard. * NOTE: Repeat the previous steps as needed. 6. If your operating system is Windows ME, click No to continue. Otherwise, click Yes to reboot your computer. 12
Summary of the content on the page No. 13
7. The "Welcome to the Install Shield Wizard for PC-Linq" dialog window appears. Click Next to continue. 8. Setup will add the program icon to the Program Folder listed below. Click Next to continue. 9. Windows has finished installing the software. Click Finish to end the Wizard. 13
Summary of the content on the page No. 14
10. The PC-Linq icon will appear on the desktop. Installation verification Because the docking station is USB 2.0, the hub driver is based on the host device. The device name may vary on your host device driver. Windows 98SE 14
Summary of the content on the page No. 15
15
Summary of the content on the page No. 16
Windows ME 16
Summary of the content on the page No. 17
17
Summary of the content on the page No. 18
Installation for Windows 2000 1. The H-DS20L Install wizard helps you install a device driver. Click Next to continue. 2. Select "Search for a suitable driver for my device [recommended]." Click Next to continue. 18
Summary of the content on the page No. 19
3. Select "Floppy disk drives" and click Next to continue. 4. The wizard found a driver. Click Next to continue. 19
Summary of the content on the page No. 20
5. Select "C:\WINNT\system32\drivers" for built-in hub driver (usbhub20.sys). Click Open to continue. 6. Click OK to continue. 20
