Summary of the content on the page No. 1
MultiConnect Adapter
Serial-to-Serial Adapter with IP
User Guide
Summary of the content on the page No. 2
MultiConnect Adapter User Guide Serial-to-Serial Adapter (MTS2SA-T & MTS2SA-T-R) PN S000354A, Version A Copyright This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2004, by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantabi
Summary of the content on the page No. 3
Table of Contents Table of Contents Chapter 1 – Product Description & Specifications.................................................................................. 6 Product Description ................................................................................................................................... 6 Applications ............................................................................................................................................... 6 Types of
Summary of the content on the page No. 4
Table of Contents Chapter 10 – Modem Mode AT Commands, S-Registers, Result Codes............................................. 85 Escape Code Sequence +++ .................................................................................................................. 85 Command Organization........................................................................................................................... 85 Command Types ...............................................................
Summary of the content on the page No. 5
Table of Contents Chapter 14 – POP3 Client....................................................................................................................... 153 Introduction............................................................................................................................................ 153 Setup and Configuration Prerequisites.................................................................................................. 153 Optional Configuration for Deleti
Summary of the content on the page No. 6
Chapter 1 – Product Description and Specifications Chapter 1 – Product Description & Specifications Product Description The MultiConnect serial-to-serial adapter enables installed serial devices to connect to the Internet for remote monitoring, control and configuration. Internet-Enable Any Device. The MultiConnect adapter provides the powerful ability to IP-enable serial devices allowing more options for data acquisition, device management, and industrial control than would otherwi
Summary of the content on the page No. 7
Chapter 1 – Product Description and Specifications Types of Adapters Available Product Adapter Description Region MTS2SA-T Serial-to-Serial + IP (External Power) Global MTS2SA-T-R Serial-to-Serial + IP (RS-232 Power) Global Note: The RS-232–powered adapters are powered through the DSR pin of the RS-232 cable. Package Contents • One MultiConnect Adapter • One universal power supply with power cord included with the externally powered adapters • One RS-232 cable included with the R
Summary of the content on the page No. 8
Chapter 1 – Product Description and Specifications Specifications Category Description Memory 8 MEG 2 MEG Flash Memory Protocols Supported ARP, DHCP, FTP, HTTP, ICMP, IP, POP3, PPP, SMTP, TCP, Telnet, TFTP, and UDP Standard DCE serial Serial Interface Data Formats Serial, binary, asynchronous Data Rates 300; 1200; 2400; 4800; 9600; 19200; 38400; 57600; 115200; 230400 bps Flow Control RTS/CTS (hardware) Management Serial; Telnet Username and password authentication using local d
Summary of the content on the page No. 9
Chapter 1 – Product Description and Specifications Category Description High performance 10/100BaseT Ethernet bridge Intelligent Features Half duplex or full duplex support on the WAN interface 256 frame buffer Stores 10,000 MAC addresses Automatically learns MAC addresses Serial interface supports DTE speeds to 230K bps External and RS-232 power options High performance processor runs ARP, DHCP, FTP, HTTP, ICMP, IP, POP3, PPP, SMTP, SNMP, SNMP, TCP, Telnet, TFTP, UDP protocols Comm
Summary of the content on the page No. 10
Chapter 1 – Product Description and Specifications LED Indicators Name Description ACT Activity – Lit when data is being transmitted or received. STS Status – Blinks to indicate that the unit is functioning. RS-232 9-Pin Connector Pinout Pin 5 Pin 1 Pin 6 Pin 9 Pins for the Serial-to-Serial Adapter when Power Is Supplied Externally Pin Description 1 DCD 2 RX Data 3 TX Data 4 DTR 5 Ground 6 DSR 7 RTS 8 CTS 9 RI Pins for the Serial-to-Serial Adapter when Pow
Summary of the content on the page No. 11
Chapter 2 – Installation Chapter 2 – Installation Attaching the MultiConnect to a Fixed Location The MultiConnect adapter is design to be used on the desktop or to be panel-mounted. To attach the bracket for panel-mounting, following these steps: 1. Typically, the MultiConnect adapter is mounted against a flat surface with two mounting screws. Drill the mounting holes at the desired location. The mounting holes must separated by 4 -7/16 inches center-to-center. 2. To att
Summary of the content on the page No. 12
Chapter 2 – Installation Serial-to-Serial Adapter Installation Connecting the Cables Serial-to-Serial Adapter Front Back shown with External Power Option 1. Plug one end of the RS-232 cable into the front of the Serial-to-Serial adapter. Plug the other end into the RS-232 connector on the modem that is setup with an Internet connection. 2. Plug one end of the other RS-232 cable into the back of the Serial-to-Serial adapter. Plug the other end into the RS-232 conne
Summary of the content on the page No. 13
Chapter 2 – Installation Connecting the Power The adapters are powered in one of two ways: • Through the DSR Pin of the RS-232 Cable Adapters powered this way are shipped with an RS-232 cable that has a power pin instead of a DSR pin. • Through an External Power Supply Adapters powered this way are shipped with a universal power supply and its accompanying power cord and an RS-232 cable that has a DSR pin instead of a power pin. Connecting the External Power 1. Plug the power supp
Summary of the content on the page No. 14
Chapter 3 – Managing and Configuring the MultiConnect Adapter Chapter 3 – Managing and Configuring the MultiConnect Adapter Two Ways to Login Login Using TTY • Use TTY to configure your MultiConnect IP for the first time. Configure the host serial port using the defaults listed below: Baud: 115.2K Data: 8 Parity: N Stop: 1 Flow-Control: None • Press the Enter key three times to get to the Login prompt or send three carriage returns. • At the Login prompt, type admin. At the P
Summary of the content on the page No. 15
Chapter 4 – Command Line Interface (CLI) Chapter 4 – Command Line Interface (CLI) The MultiConnect commands are grouped based on the functionality. • General Setup Commands • IP Setup Commands • Serial Setup Commands • PPP Setup Commands • HTTP Setup Commands • SMTP Setup Commands • POP3 Setup Commands • FTP Client Setup Commands • SNTP Client Setup Commands General Notes • Required command parameters are indicated between < >. • Optional command parameters are indicated betwe
Summary of the content on the page No. 16
Chapter 4 – Command Line Interface (CLI) General Commands – Setup General Setup Commands General setup of a MultiConnect IP is port-independent (physical S0, S1 etc.). The following command set is used to set the global configuration of MultiConnect IP. Command Syntax dialout serial s0 Description Manual Telnet dialout (Internet-to-serial connectivity). Invoked from the command shell. NA Default Value OK Success Error 1. Too few arguments “Usage: dialout serial
Summary of the content on the page No. 17
Chapter 4 – Command Line Interface (CLI) General Commands – Setup Command Syntax reset modem Description At will, reset the built-in modem. Default Value NA Success OK Error 1. Too few arguments Possible argument(s) are modem Command Syntax save Description Command to Save the configuration to the flash and reboot. NA Default Value OK Success Command Syntax telnet [] Manual serial dial-in (device port to modem port connectivity). Description I
Summary of the content on the page No. 18
Chapter 4 – Command Line Interface (CLI) General Commands – Setup Command Syntax user password Description Change the password for a user. Default Value NA Success OK Error 1. Too few arguments “Too few arguments. Possible value(s) are username followed by password” 2. Unable to change the password “Password does not match Unable to change user password” Command Syntax set operation-mode Description modem - In the modem m
Summary of the content on the page No. 19
Chapter 4 – Command Line Interface (CLI) General Commands – Setup Command Syntax set login Description Prompts the Login for the command shell when enabled, and doesn't when disabled. Enable Default Value OK Success Error 1. Too few arguments "Usage: set login Type 'set login ?' for more information" 2. Invalid string "error: set login " Command Syntax set login auto-dialout-login Enables/Disables authentication for T
Summary of the content on the page No. 20
Chapter 4 – Command Line Interface (CLI) General Commands – Setup Command Syntax show buildrun Description Command Line Configuration - History. Upon invoking any command, either through Telnet or Serial TTY, the command is added to the buildrun file. This is very useful in case of version updates. NA Default Value OK Success Error 1. Too few arguments "Too few arguments. Possible argument(s) are serial date statistics users buildrun ip sys-info
