Summary of the content on the page No. 1
P-660RU-Tx v2
ADSL2+ Ethernet / USB Router
Quick Start Guide
Version 3.40
Edition 3
5/2008
Summary of the content on the page No. 2
P-660RU-Tx v2 Quick Start Guide Overview The P-660RU-Tx v2 is an ADSL router with both USB and Ethernet ports. See your User’s Guide for background information on all features. This Quick Start Guide shows you how to: • Connect the hardware. • Set up your Internet connection. The device should connect to the Internet automatically if it is preconfigured. If you were given Internet connection information from your Internet Service Provider (ISP), you may have to set up the connec- tion manua
Summary of the content on the page No. 3
P-660RU-Tx v2 Quick Start Guide 1 Hardware Connections There are two ways to connect your computer or computer network to the P-660RU-Tx v2: Option A: Connect via Ethernet. See page 2. Option B: Connect via USB (you will need to install the USB driver). See page 4. Option A: Connect via Ethernet 1ETHERNET: Use the yellow Ethernet cable to connect a computer to the ETHERNET port for initial configuration and/or Internet access. 2
Summary of the content on the page No. 4
P-660RU-Tx v2 Quick Start Guide 2DSL: Use the gray telephone wire to connect your P- 660RU-Tx v2’s DSL port to a telephone jack (or to a splitter, if one is already installed). 3POWER: Use the power adaptor provided with your P- 660RU-Tx v2 to connect an appropriate power source to the POWER socket. Make sure the power source is on. 4 Push in the POWER button. 5 Look at the lights on the front panel. •The POWER light blinks while your P-660RU-Tx v2 starts up and stays on once it is ready.
Summary of the content on the page No. 5
P-660RU-Tx v2 Quick Start Guide If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor. Option B: Connect via USB 4
Summary of the content on the page No. 6
P-660RU-Tx v2 Quick Start Guide Do NOT connect the same computer to both the USB and ETHERNET ports on the P-660RU-Tx v2. 1USB: Connect the provided USB cable to the P-660RU-Tx v2’s USB port. 2DSL: Use the gray telephone wire to connect your P- 660RU-Tx v2’s DSL port to a telephone jack (or to a splitter, if one is already installed). 3POWER: Use the power adaptor provided with your P- 660RU-Tx v2 to connect an appropriate power source to the POWER socket. Make sure the power source is
Summary of the content on the page No. 7
P-660RU-Tx v2 Quick Start Guide If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor. Install the USB Software If you want to connect to the Internet through the P-660RU-Tx v2's USB port, install the USB driver before you connect the P-660RU-Tx v2 to the USB port. Follow the steps for your operating system to install the USB driver. Windows Computer System Requirements • Windows 98 SE (Second E
Summary of the content on the page No. 8
P-660RU-Tx v2 Quick Start Guide 5 An install warning may appear in the Windows Vista OS. Click Allow to continue. 6 Click Next in the Welcome screen to begin the USB Installation Wizard. Follow the installation prompts. You may need to restart your computer at the end of the installation. 7
Summary of the content on the page No. 9
P-660RU-Tx v2 Quick Start Guide Macintosh Computer System Requirements • Macintosh operating system versions 10.1, 10.2 and 10.3. • An available USB port Procedures 1 Save your work and close all applications. 2 Insert the included CD. A CD’s icon automatically displays on the desktop. 3 Double-click the CD's icon. 4 Double-click the MAC version of your computer. 8
Summary of the content on the page No. 10
P-660RU-Tx v2 Quick Start Guide 5 Double-click one of the following. If you selected MAC10.1, double click the P-660RU-T icon. If you selected MAC 10.2_10.3, double click the P-660RU- Tx.dmg icon. 9
Summary of the content on the page No. 11
P-660RU-Tx v2 Quick Start Guide 6 Click Continue in the Welcome screen to begin the USB installation. Follow the installation prompts. You may need to restart your computer at the end of the installation. 2 Connection Setup: Automatic Use this section to have your P-660RU-Tx v2 automatically detect and set up your Internet connection. 1 Open your web browser, and go to any web page (for example, http://www.zyxel.com). Your P-660RU-Tx v2 tries to detect your Internet connection. 2 Wait for
Summary of the content on the page No. 12
P-660RU-Tx v2 Quick Start Guide connection test screen similar to the following, go to step 5. 3 If the connection test is successful, the following screen appears. Your Internet connection is ready for you to use. 4 If the connection test is not successful, you may see a screen similar to the following. Follow the instructions in the screen. 11
Summary of the content on the page No. 13
P-660RU-Tx v2 Quick Start Guide 5 If the connection test is not successful, check your connections and restart the P-660RU-Tx v2. If you still cannot access the Internet, take the steps in the following section. You should have information provided by your Internet Service Provider. 3 Connection Setup: Wizard Use this section to set up your Internet connection if automatic Internet connection does not work (see section 2). You should have information from your Internet Service Provider (I
Summary of the content on the page No. 14
P-660RU-Tx v2 Quick Start Guide 3 Type (and retype) a new password and click Apply. You have to use a new password other than the default password 1234, or you cannot apply it successfully. 4 The system asks you to enter your new password to log in again. 13
Summary of the content on the page No. 15
P-660RU-Tx v2 Quick Start Guide 5 Select Go to Wizard setup. Click Apply. 6 Click INTERNET SETUP. Wait while your P-660RU-Tx v2 tries to detect your DSL connection. 14
Summary of the content on the page No. 16
P-660RU-Tx v2 Quick Start Guide 7 If the connection test is successful, the following screen displays. Click Finish to exit the wizard. 8 If the connection test is not successful, you may see a screen similar to one of the following. 15
Summary of the content on the page No. 17
P-660RU-Tx v2 Quick Start Guide Either click Restart the Internet Setup Wizard (if available) to have the ZyXEL Device detect your connection again, or click Next to set up your Internet connection manually. 9 Follow the instructions in the wizard. Enter your Internet connection information exactly as provided by your ISP. If you do not see the following screen, go to section 4. 4 Connection Setup: Manual Use this section to set up your Internet connection manually if you do not see the IS
Summary of the content on the page No. 18
P-660RU-Tx v2 Quick Start Guide 1 Follow steps 1 to 3 in section 3 in order to log in to the web configurator. 2 Select Go to Advanced setup. Click Apply. 3 The Status screen appears. Click Network > WAN in the navigation panel on the left of the screen. 4 The Internet Connection screen appears. Enter the information exactly as provided by your ISP and click Apply. 17
Summary of the content on the page No. 19
P-660RU-Tx v2 Quick Start Guide The fields available in this screen depend on the Mode you select. 5 If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider (ISP) for assistance. 18
Summary of the content on the page No. 20
P-660RU-Tx v2 Quick Start Guide Troubleshooting 1 If you want to verify your USB installation, • Check the status of the P-660RU-Tx v2 in the Device Man- ager window. Click Start > Settings > Control Panel > Sys- tem > Hardware and then click Device Manager. (Steps may vary depending on the version of Windows.) • Verify the status of the P-660RU-Tx v2 under Network Adapter. Check that there is no question mark on the device icon for the P-660RU-Tx v2. 2 If you cannot access the web configura
