Summary of the content on the page No. 1
ZyWALL 10
Internet Security Gateway
Quick Start Guide
Version 3.52
March 2003
Summary of the content on the page No. 2
ZyWALL 10 Introducing the ZyWALL The ZyWALL 10 is the ideal secure gateway for all data passing between the Internet and the LAN. By integrating NAT, firewall and VPN capability, ZyXEL’s ZyWALL 10 is a complete security solution that protects your Intranet and efficiently manages data traffic on your network. The embedded web configurator is easy to operate and totally independent of the operating system platform you use. You should have an Internet account already set up and have been giv
Summary of the content on the page No. 3
ZyWALL 10 Hardware Installation Rear Panel LABEL DESCRIPTION 1. 10/100M LAN Connect a computer to this port with an Ethernet cable. This port is auto-negotiating (can connect at 10 or 100Mbps). Push the UPLINK button in with a straight-through Ethernet cable or have the UPLINK button out with a crossover Ethernet cable. 2. 10 WAN Connect your cable/DSL modem to this port with the Ethernet cable that came with your modem. 3. POWER 12VDC Connect the included power adaptor (use only thi
Summary of the content on the page No. 4
ZyWALL 10 LABEL DESCRIPTION RESET You only need to use this button if you’ve forgotten the ZyWALL’s password. It returns the ZyWALL to the factory defaults (password is 1234, LAN IP address 192.168.1.1, terminal emulation settings as described above etc.; see your User’s Guide for details). The Front Panel LEDs The PWR LED turns on when you connect the power. The SYS LED blinks while performing system testing and then stays on if the testing is successful. The LAN and WAN LEDs turn on if
Summary of the content on the page No. 5
ZyWALL 10 Setting Up Your Computer’s IP Address Skip this section if your computer is already set up to accept a dynamic IP address. This is the default for most new computers. The ZyWALL is already set up to assign your computer an IP address. Use this section to set up your computer to receive an IP address or assign it a static IP address in the 192.168.1.2 to 192.168.1.254 range with a subnet mask of 255.255.255.0. This is necessary to ensure that your computer can communicate with yo
Summary of the content on the page No. 6
ZyWALL 10 6. Click Advanced. Remove any previously installed gateways in the IP Settings tab and click OK to go back to the Internet Protocol TCP/IP Properties screen. 7. Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields. If you have more than two DNS servers, click Advanced, t
Summary of the content on the page No. 7
ZyWALL 10 Accessing Your ZyWALL Via Web Configurator Step 1. Launch your web browser. Enter “192.168.1.1” as the web site address. Web site address. Step 2. The default password (“1234”) is already in the password field (in non-readable format). Click Login to proceed to a screen asking you to change your password. Click Reset to revert to the default password in the password field. Default password. Step 3. It is highly recommended you change the default password! Enter a new passwo
Summary of the content on the page No. 8
ZyWALL 10 WIZARD Navigation panel LOGOUT Using the Wizard to Configure for Internet Access Step 1. Click Wizard Setup in the main menu to display the first wizard screen. System Name is for identification purposes. Enter your computer's "Computer Name". The Domain Name entry is what is propagated to the DHCP clients on the LAN. If you leave this blank, the domain name obtained by DHCP from the ISP is used. Click Next to continue. 7
Summary of the content on the page No. 9
ZyWALL 10 Step 2. The second wizard screen has three variations depending on what encapsulation type you use. Use the information in Internet Account Information to fill in fields. Choose Ethernet when the WAN port is used as a regular Ethernet. Choose from Standard or a RoadRunner version. You’ll need User Name, Password and Login Server IP Address for some Roadrunner versions. Point-to-Point Protocol over Ethernet (PPPoE) also functions as a dial-up connection. Therefore you’ll a
Summary of the content on the page No. 10
ZyWALL 10 Test Your Internet Connection Launch your web browser and navigate to www.zyxel.com. You don’t need a dial-up program such as Dial Up Networking. Internet access is just the beginning. Refer to the User’s Guide for more detailed information on the complete range of ZyWALL features. Troubleshooting PROBLEM CORRECTIVE ACTION None of the Make sure that you have the correct power adapter connected to the ZyWALL and plugged in to an LEDs turn on appropriate power source. Check all c
