Summary of the content on the page No. 1
™
DT
Cellular Signal Booster
463105
Need help? www.WilsonElectronics.com Tech Support 866-294-1660
Mon.- Fri. Hours: 7 am to 6 pm MST
Summary of the content on the page No. 2
IT IS VERY IMPORTANT THE SIGNAL BOOSTER UNIT IS DESIGNED TO POWER YOUR SIGNAL FOR USE IN AN INDOOR, TEMPERATURE- ! ! BOOSTER USING A SURGE CONTROLLED ENVIRONMENT (LESS PROTECTED AC POWER THAN 150 DEGREES FAHRENHEIT). IT IS STRIP WITH AT LEAST A 1000 NOT INTENDED FOR USE IN ATTICS OR SIMILAR JOULE RATING. LOCATIONS SUBJECT TO TEMPERATURES IN EXCESS OF 150°F. FAILURE TO DO THIS WILL VOID YOUR WARRANTY IN THE EVENT OF A POWER SURGE OR LIGHTNING STRIKE. Installation Instructions for the Follo
Summary of the content on the page No. 3
Package Contents Accessories packaged may not exactly match the below photos due to different kit options SIGNALBOOST DT Desktop Antenna Cradle Antenna Kit Coax Cable AC Power Supply Cable Cradle Antenna (301213) (30’ 950630) 6V / 2.5A Connector 20’ RG6 coax cable (Not included with some models) (971129) (311141-0620) (859912) Included Accessories Optional Antenna Upgrade Kit 314473-0640 Kit 991171 Includes P ole Mount Panel Antenna 40’ RG6 cable 3. Window Mount 1. Pole Mount 2. Wall Mount (P
Summary of the content on the page No. 4
Rotate in small increments Find the Strongest Cellular Signal Before you install your DT signal booster, you must determine the location of the best available cellular signal. This will affect the location of your Outside Antenna and will help you get the best performance from your DT. You can find the strongest signal outside your building, typically at the highest point available, using any of the following d. Once you have determined which methods: direction provides the stro
Summary of the content on the page No. 5
W i n twist through d o twist through w f a o f c e c s e l l g t e o n w e r e a r l d i r e c t i o n 4. Insert the Outside Antenna into the Quick Install - Inside Window cradle. Mount Option Additional installation options on pg. 6-12 Find the Strongest Cellular Signal (See page 4 for suggested methods.) Ready to Install Inside Window Mount 1. Select a location on the inside of a window as high as possible and at least 20 feet from where the DT will be located. Note tha
Summary of the content on the page No. 6
8. Connect the DT to a surge protected AC Installation Options power strip with at least a 1000 Joule Outside Pole Mount rating. If your DT is working correctly, the lights will be green. (Best Option) 1. Select a location on the roof where the Outside Antenna can be mounted on a pole maintaining at least 20 feet of vertical or horizontal separation from the inside Desktop Antenna. If the lights are orange or red, see Place the desktop signal the “Troubleshooting” section o
Summary of the content on the page No. 7
5. Connect the supplied coax cable to 4. Route the cable as desired to the the antenna lead cable on the Outside location of the DT. If you need to Antenna. connect both coax cables, use the Cable Connector provided. Additional Considerations 6. Route the cable as desired to the location of the DT. If you need to Whichever installation you choose, connect both coax cables, use the Cable keep the following guidelines in mind to Connector provided. Secure the cable maximize your si
Summary of the content on the page No. 8
If possible, place the Desktop 5. If you do not know how to mount Signal Antenna directly beneath the hardware or run coax cable through placement of the Outside Antenna walls, ceilings and floors, get help from location. This creates a maximized one of Wilson’s certified installers at signal zone within the room where the www.wilsonelectronics.com/installers Desktop Antenna remains. or from a qualified contractor or electrician. You can also try the Inside Window Mount option (pg.5
Summary of the content on the page No. 9
3. Attach the Inside Antenna to the Troubleshooting & connector labeled “Inside Antenna.” Understanding Lights The DT includes two indicator lights, one for each band (for more information about the frequency bands used by your cell service provider visit wirelessadvisor.com.) All indicator lights will be green, orange or red. Green indicates the unit is powered 4. Ensure the Inside Antenna is facing away from both the DT and the and working properly. You always Outside Antenna
Summary of the content on the page No. 10
c) Y ou need to increase the distance c) If the light remains orange, contact between the Outside Antenna and the Wilson Electronics Technical the Desktop Antenna by moving them Support Team for assistance: 866- horizontally and/or vertically farther 294-1660. apart making sure they are not facing Fixing Blinking Red & Orange Light towards each other. Issues If one or more of the lights on Signal Booster are blinking red and orange, it indicates that the Signal Booster is experiencing
Summary of the content on the page No. 11
Why do I need to maintain at least 20 feet of Additional FAQ: separation, but no more than 50 feet? OR What hours can I contact tech support? Why do I need to create so much distance between the antennas? Technical Support can be reached from 7:00am to 6:00pm MST, by calling (866-294-1660), or by Antennas connected to a booster create a sphere email, at tech@wilsonelectronics.com. of signal. When these sphere’s overlap, a condition called oscillation occurs. This oscillation How does
Summary of the content on the page No. 12
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________
Summary of the content on the page No. 13
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________
Summary of the content on the page No. 14
Signal Booster Specifications SIGNALBOOST™ DT™ Specifications Model Number 460005 Outside antenna connectors F-Female / SMA-Female Outside antenna impedance 75 / 50 Ohms Inside antenna connectors SMA Inside antenna impedance 50 Ohms Dimensions 6.5 x 4.25 x 1.75 inch (16.5 x 10.7 x 4.4 cm) Weight 0.47 lbs (0.213 kg) Frequency 824-894 MHz / 1850-1990 MHz Power output 800 MHz 1900 MHz Power output for single cell phone (uplink) dBm 24.9 22.5 Power output for single received channel (downlink) dBm -
Summary of the content on the page No. 15
Safety Guidelines WARNING: T o uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas and 4 feet of separation distance from Desktop antennas. WARNING: C onnecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. WARNING: U se only the power supply provided in this package. Use of a non-Wilson Electronics product may damage yo
Summary of the content on the page No. 16
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 2-Year Warranty Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a
