Cisco Systems 700 Series user manual

Summary of the content on the page No. 1

Cisco 700 Series Router Cabling and Setup
Quick Start Guide
This document describes the basic process of cabling and configuring the Internet access device, the
Cisco 700 series router. For advanced cabling information, refer to the Cisco 700 Series Router
Installation Guide. For advanced configuration information, refer to the Cisco 700 Series Router
Command Reference and the Cisco 700 Series Router Software Configuration Guide. These documents can
be found on the Cisco Documentation CD-ROM and

Summary of the content on the page No. 2

10BASET ISDN S/T CONFIG S 0 10BASET ISDN S/T CONFIG S 0 NODE HUB NODE HUB CISCO 776 CISCO 776 +5V ---1.5A +/-5% -30V--- 0.2A +/-25% +5V ---1.5A +/-5% -30V--- 0.2A +/-25% Verify the PC Setup Before you begin, verify that each computer that will be connected to the computer has a network interface card (NIC) installed and TCP/IP loaded. Connect a 760 Series Router to a PC or Hub Step 1 If you are connecting the router to a computer, connect the yellow Ethernet cable from the yellow Ethernet port o

Summary of the content on the page No. 3

ETHERNET ETHERNET 4 3 ISDN S/T CONFIG 2 1 S 0 NT-1 4 3 2 1 ISDN S/T CONFIG S NT-1 0 CISCO 776 CISCO 776 ISDN U ISDN U +5V ---1.5A +/-5% -30V--- 0.2A +/-25% +5V ---1.5A +/-5% -30V--- 0.2A +/-25% Connect a 770 Series Router to a PC or Hub Step 1 If you are connecting to a computer, connect a yellow Ethernet cable from a yellow Ethernet port on the rear panel of the router to the Ethernet port on the network interface card on the computer. If you are connecting the router to a hub, omit this step.

Summary of the content on the page No. 4

10BASET ISDN S/T CONFIG S 0 NT-1 10BASET ISDN S/T CONFIG S 0 NODE HUB NODE HUB CISCO 776 ISDN U CISCO 776 +5V ---1.5A +/-5% -30V--- 0.2A +/-25% +5V ---1.5A +/-5% -30V--- 0.2A +/-25% Connect the ISDN Line This section shows how to connect the router to the ISDN. Connect a Cisco 762 or Cisco 776 Router to the ISDN Line Step 1 Connect the red ISDN U cable to the red port labeled ISDN U on the rear panel of your router. Step 2 Connect the other end of the ISDN U cable directly to an RJ-45 ISDN wall

Summary of the content on the page No. 5

ETHERNET 1 2 3 ISDN S/T ??? CONFIG 4 S 0 BRI CISCO 776 +5V ---1.5A +/-5% -30V--- 0.2A +/-25% Step 2 Connect the other end of the ISDN S/T cable to the ISDN wall socket. Note If necessary, use the enclosed RJ-45-to-RJ-11 adapter to connect to an RJ-11 ISDN wall jack. Connect the Power and Turn On the Router This section describes the procedure for supplying power to the router. Step 1 Connect the power supply cable to the round, black power connector on the rear panel of the router, connect the p

Summary of the content on the page No. 6

Setup the Router to Access a Corporate Network or Internet Service Provider A Cisco Fast Step CD-ROM and a RVS-COM Lite CD-ROM is included with your router. We recommend that you use Cisco Fast Step software to set up the router and RVS-COM Lite software for Common ISDN Application Programmers Interface (CAPI) support. Cisco Fast Step Software Cisco Fast Step software simplifies the setup and monitoring of Cisco routers. It runs on Microsoft Windows 95, Windows 98, and Windows NT 4.0 personal co

Summary of the content on the page No. 7

78-10157-01 7

Summary of the content on the page No. 8

Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified Internetwork Expert logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the Cisco Powered Network logo, Cisco Systems Capital, the Cisco Systems Capital logo, Cisco Systems Networking Academy, the Cisco Systems Networking Academy logo, the Cisco Technologies logo, ConnectWay, Fast Step, FireRunner, GigaStack, IGX, Internet Quotient,