Summary of the content on the page No. 1
D-Link
DI-704
User Manual
Summary of the content on the page No. 2
LIMITED WARRANTY D-Link Systems, Inc. (“D-Link”) provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor. Limited Hardware Warranty: D-Link warrants that the hardware portion of the D-Link products described below (“Hardware”) will be free from material defects in workmanship and materials from the date of original retail purchase of the Hardware, for the period set forth below applicab
Summary of the content on the page No. 3
Spare parts and spare kits Ninety (90) days D-Link’s sole obligation shall be to repair or replace the defective Hardware at no charge to the original owner. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or of an identical make, model or part; D-Link may in its discretion may replace the defective Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is substantiall
Summary of the content on the page No. 4
product shall be insured and shipped to D-Link, 53 Discovery Drive, Irvine CA 92618, with all shipping costs prepaid. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing require
Summary of the content on the page No. 5
1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät is vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf
Summary of the content on the page No. 6
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the United States Copyright Act of 1976. CE Mark Warning This is a Class B product. In a domestic environ
Summary of the content on the page No. 7
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. VCCI Warning VII
Summary of the content on the page No. 8
Table of Contents Chapter 1 Introduction.................................................................................1 1.1 Functions and Features.................................................................... 1 1.2 Packing List..................................................................................... 2 Chapter 2 Hardware Installation..................................................................3 2.1. Panel Layout..........................................................
Summary of the content on the page No. 9
Chapter 1 Introduction Congratulations on your purchase of the DI-704 Broadband Router. The DI-704 is specifically designed for Small Office and Home Office needs. It provides a complete solution for Internet surfing and office resource sharing, and is easy for non-technical users to configure and operate. Instructions for installing and configuring the DI-704 can be found in this manual. Before you install and use the DI-704, please read this manual carefully to fully understand the functions
Summary of the content on the page No. 10
Internet Explorer. l Access Control supported Allows you to assign different access rights for different users. l Virtual Server supported Enables you to expose WWW, FTP and other services on your LAN to be accessible to Internet users outside of your LAN. l User-Definable Application Sensing Tunnel User can define the attributes to support the special applications requiring multiple connections, like Internet gaming, video conferencing, Internet telephony and so on, then the DI-704 can sense th
Summary of the content on the page No. 11
Chapter 2 Hardware Installation 2.1. Panel Layout 2.1.1. Front Panel Figure 2-1 Front Panel RESET When RESET is pushed, system settings will be set to factory defaults. M1&M2 System status indicators, Orange. M1 is flashed once per second to indicate system is alive. When system is busy, M2 is lighted. WAN & LAN Ethernet port indicators, Green. The LED flickers when LAN or WAN port is sending or receiving data. Link/Act. Link status indicators, Green. The LED flickers when the corresponding por
Summary of the content on the page No. 12
Power Power inlet. This is where you connect the included power adapter. Note that, the included power adapter is DC 5V/1A. Using the wrong type of power adapter may cause damage to the DI-704. 2.2. Installation Requirements The DI-704 can be positioned at any convenient place in your office or house. No special wiring or cooling requirements is needed. However, you should comply with the following guidelines to install: l Place the DI-704 on a flat horizontal surface. l Keep the DI-704 away fro
Summary of the content on the page No. 13
Figure 2-5 Setup of LAN connections for DI-704. 2. Setup WAN connection: prepare an Ethernet cable for connecting the DI-704 to your cable/xDSL modem or Ethernet backbone. Figure 2-5 illustrates the WAN connection. 3. Power on: Connect the power cord to power inlet and turn the power switch on. The DI-704 will automatically enter the self-test phase. When in the self-test phase, the indicators M1 and M2 will be lighted ON for about 5 seconds, and then M1 and M2 will flash three times to indicate
Summary of the content on the page No. 14
Chapter 3 Network Settings and Software Installation To use the DI-704 correctly, you have to properly configure the network settings of your computers and install the attached setup program into your MS Windows platform (Windows 95/98/Me/NT/2000). 3.1 Make correct network settings to the computer The default IP address of the DI-704 is 192.168.123.254, and the default subnet mask is 255.255.255.0. These addresses can be changed to meet your need, but the default values are used in this manual.
Summary of the content on the page No. 15
there must be something wrong with the installation. Follow the steps again to make sure the network settings are correct. You should check the following items in sequence: 1. Is the Ethernet cable correctly connected between the DI-704 and your computer? Tip: The LAN LED of the DI-704 and the link LED of network card on your computer must be lighted. 2. Is the TCP/IP environment of your computers properly configured? Tip: If the IP address of the DI-704 is 192.168.123.254, the IP address of yo
Summary of the content on the page No. 16
Chapter 4 Configuring The DI-704 The DI-704 provides a Web based configuration scheme, that is, configuring by Netscape Communicator or Internet Explorer. This approach can be adopted in any MS Windows, Macintosh or UNIX based platform. 4.1 Start-up and Log in Activate your browser, open settings, and disable the proxy or add the IP address of the DI-704 into the exceptions box. Then, type the DI-704’s IP address [for example (default setting): http://192.168.123.254] in the Location (for Netsc
Summary of the content on the page No. 17
the System Password field and click on the Log in button. If the password is correct, the web appearance will be changed into administrator configure mode. As listed in its main menu, there are several options for system administration. 4.2 Status This option provides the function for observing the DI-704’s working status: A. WAN Port Status. If the WAN port is assigned a dynamic IP, there may appear a “Renew” or “Release” button on the Sidenote column. You can click this button to renew or rele
Summary of the content on the page No. 18
4.3 Tools This option enables you to change the administrator password, view the log, and clone the MAC address. You can also reboot the DI-704 by clicking the Reboot button. Note: We strongly recommend that the system password be changed for security reasons. If you forget the system password, please refer to Appendix A to reset a new one. 10
Summary of the content on the page No. 19
4.4 Setup This option is crucial to enable the DI-704 to work properly. The setting items and the web appearance depend on the WAN type. Choose correct WAN type before you start. 1. LAN IP Address: the DI-704’s IP address. The default address is 192.168.123.254. You can change it to your need. 2. WAN Type: WAN connection type of your ISP. You can click the Change button to choose a correct one from the following four options: A. Static IP Address: ISP assigns you a static IP address. B. Dynamic
Summary of the content on the page No. 20
4.4.1 Static IP Address WAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS: enter the proper setting value provided by your ISP. 4.4.2 Dynamic IP Address 1. Host Name: optional. Required by some ISPs, for example, @Home. 2. Renew IP Forever: this feature enables the DI-704 to renew its IP address automatically when the lease time is expired even if the system is idle. 4.4.3 PPP over Ethernet 1. PPPoE Account and Password : the account and password your ISP assigned to you. If you do
