Summary of the content on the page No. 1
Summary of the content on the page No. 2
Copyright © by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents he
Summary of the content on the page No. 3
Federal Communication Commission Interference Statement FCC Part 68 This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must provide this information to the telephone company upon request. The REN is useful to determine the quantity of devices you may connect to the telephone line and still have all of those devices ring when your number
Summary of the content on the page No. 4
this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Installation This device is equipped with a USOC RJ11C connector. FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limi
Summary of the content on the page No. 5
FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re
Summary of the content on the page No. 6
R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with
Summary of the content on the page No. 7
Contents 1. INTRODUCTION ....................................................... 1 1.1. FEATURES ........................................................................... 2 1.2. MINIMUM REQUIREMENTS .................................................. 3 1.3. PACKAGE CONTENT ............................................................ 3 1.4. HARDWARE PLACEMENT .................................................... 4 1.4.1. Rear Panel .....................................................
Summary of the content on the page No. 8
5.2.3.2. DHCP Relay ...................................................................................... 48 5.2.3.3. DHCP Server .................................................................................... 49 5.2.3.4. ARP Table ......................................................................................... 52 5.2.3.5. Bridging ............................................................................................ 52 5.2.4. Wireless ..............................
Summary of the content on the page No. 9
6. TROUBLESHOOTING .......................................... 102 7. GLOSSARY ............................................................. 106
Summary of the content on the page No. 10
1. Introduction Congratulations on purchasing Edimax AR-7266WnA (AR-7266WnB) 300Mbps Wireless N ADSL2/2+ Router. This router is a cost-effective ADSL2/2+ router, with the combination of an ADSL2/2+ modem, router, Ethernet network switch and wireless access point, you can surf the Internet through your ADSL2/2+ ADSL connection without investing other devices. This router can support downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 1Mbps. It supports
Summary of the content on the page No. 11
1.1. Features ADSL2/2+ Compliance • Support downstream rates of up to 24Mbps and upstream rates of up to 1Mbps. • Compliant to ITU-T G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3 (ADSL2), G.992.4 (splitterless ADSL2), G.992.5 (ADSL2+) for Annex A, B. (Annex A and B are supported in different H/W platform) • Multiple Protocols over AAL5 (RFC 1483/2684). • PPP over AAL5 (RFC 2364). • PPP over Ethernet (RFC 2516). Supports 802.11b/g/n Wireless Access Point • Complies with IEEE 802.11b/g
Summary of the content on the page No. 12
1.2. Minimum Requirements The following devices are necessary to configure and use the ADSL2+ Router: • A PC with Pre-installed Ethernet Adapter (Required) and a Web-Browser (Internet Explorer 4.0 or higher) • RJ-45 Ethernet crossover cable (Included in the package) • RJ-11 (ADSL Ready) phone Line 1.3. Package Content • One ADSL2+ Router (Annex A or B) • One Power Adapter (12VDC, 1A) • Two 3dBi Antenna • One RJ-45 Ethernet Cable (100 cm) • One RJ-11 Telephone Line (180 cm) • One
Summary of the content on the page No. 13
1.4. Hardware Placement 1.4.1. Rear Panel Item Name Description Antenna A/B These antennas are 3dBi dipole antennas. Radio Switch the button to activate or deactivate the wireless ON/OFF functions. Reset / WPS Reset the router to factory default settings (clear all settings) or start WPS function. Press this button and hold for 10 seconds to restore all settings to factory defaults, and press this button for less than 5 seconds to start WPS function. 1 - 4 The router’s 4 LAN ports
Summary of the content on the page No. 14
LED Light Status Description POWER (Green) On Router is switched on and correctly powered. WLAN (Yellow) On Wireless LAN WPS is on. Off Wireless LAN is disabled Blinking Wireless traffic is transmitting or receiving ADSL (Green) On Connected to an ADSL DSLAN successfully Blinking ADSL line is not connect to internet. The LAN cable is connected to the router LAN LNK/ACT (Port 1-4) On No network connection. Off Network traffic transferring or receiving Blinking through
Summary of the content on the page No. 15
2. Hardware Installation Step 1. Connect the ADSL Line Use the supplied RJ-11 telephone cable, connect the router from the ADSL port to your telephone socket with an ADSL micro filter plugged in. Step 2. Connect the router to your LAN network Connect the router to your PC, hub or switch by attached the Ethernet cable to the LAN port of the router. Step 3. Connect the Power Adapter to the Router Connect the power adapter to the power jack on the rear panel of the router and swit
Summary of the content on the page No. 16
3. Setup Wizard 3.1. Getting Started Before you start, please check the following items: 1. Please make sure that you have connected the ADSL cable to the router correctly. When the ADSL cable is worked normally, the ADSL LED will be on. 2. Uninstall all of dial up programs if you have installed previously for the USB modem or other dial up devices. 3. It is recommended to configure the router through the Ethernet cable before you have set the wireless functions correctly. This wizard
Summary of the content on the page No. 17
The wizard will guide you to setup “ Internet Connection” , “ ESSID “ , Wireless security “ and “ Firmware Upgrade “ . 8
Summary of the content on the page No. 18
9
Summary of the content on the page No. 19
Please choose the product type which you bought . The default password is “ 1234 “ . 10
Summary of the content on the page No. 20
Please select your country and ISP .If the country or ISP is not listed , please select “Others” from the list. Click” Next “ to finish all configurations of Internet Connection , Wireless setting and Firmware Upgrade . 3.3. Manually Set ISP If you cannot find the ISP from the wizard, please follow the procedures below to set the ISP settings manually. Before configuring the ISP manually, please check with your ISP (Internet Service Provider) what kind of the service is provided
