Summary of the content on the page No. 1
i
Summary of the content on the page No. 2
Regulatory notes and statements Wireless LAN, Health and Authorization for use The use of Wireless LAN devices may be restricted in some situations or environments for example: ·On board of airplanes, or ·In an explosive environment, or ·In case the interference risk to other devices or services is perceived or identified as harmful In case the policy regarding the use of Wireless LAN devices in specific organizations or environments (e.g. airports, hospitals, chemical/oil/gas industr
Summary of the content on the page No. 3
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC
Summary of the content on the page No. 4
or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.6.1: (2005-09) Electromagnetic
Summary of the content on the page No. 5
0560 Česky TRENDnet tímto prohlašuje, že tento TEW-670APB je ve shod ě se základními požadavky a [Czech] dalšími p říslušnými ustanoveními sm ěrnice 1999/5/ES. Dansk Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW-670APB overholder de [Danish] væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklärt TRENDnet, dass sich das Gerät TEW-670APB in Übereinstimmung mit den [German] grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen
Summary of the content on the page No. 6
Slovensky TRENDnet týmto vyhlasuje, že TEW-670APB spĺňa základné požiadavky a všetky príslušné [Slovak] ustanovenia Smernice 1999/5/ES. Suomi TRENDnet vakuuttaa täten että TEW-670APB tyyppinen laite on direktiivin 1999/5/EY [Finnish] oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska Härmed intygar TRENDnet att denna TEW-670APB står I överensstämmelse med de väsentliga [Swedish] egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/
Summary of the content on the page No. 7
TABLE OF CONTENT About This Guide ........................................................................................................................................................................................... 1 Overview of this User’s Guide .................................................................................................................................................................. 1 Introduction .................................................................
Summary of the content on the page No. 8
ABOUT THIS GUIDE Congratulations on your purchase of this 300Mbps Dual Band Wireless N Access Point. This manual helps to describe the innovating wireless technology that can help you build a wireless network easily! The manual contains detailed instructions in operation of this product. Please keep this manual for future reference. Overview of this User’s Guide Introduction. Describes the 802.11a/b/g/n Dual Band WLAN Access Point and its features. Unpacking and Se
Summary of the content on the page No. 9
INTRODUCTION The 300Mbps Dual Band Wireless N Access Point (TEW-670APB) creates a high performance dual band wireless n network with up to 14x the speed and 4x the coverage of wireless g. Create a wireless network using either the more common 2.4GHz or the uncongested low-interference 5GHz wireless radio frequency with Dual Band wireless n technology. Extend your wireless network by adding additional wireless access points using the Wireless Distribution System (WDS) feature. Monitor de
Summary of the content on the page No. 10
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Access Point. Unpacking Open the box of the Access Point and carefully unpack it. The box should contain the following items: TEW-670APB Multi-Language Quick Installation Guide Power Adapter CD-Rom (User’s guide) If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Wireless Access Point can be performed using the following steps: Locat
Summary of the content on the page No. 11
HARDWARE INSTALATION Front panel The figure below shows the LED Indicator of the Wireless LAN Access Point. Power: This indicator lights green when the Access Point is turned on. Status: This indicator blinkswhen the WLAN AP is working successfully. Otherwise, an on or off means the function of the WLAN AP has failed. LAN: This indicator lights green when the LAN port has successfully connected to an Ethernet network. Otherwise, the indicator blinks while transmitting and receivi
Summary of the content on the page No. 12
Rear Panel The figure below shows the rear panel of the Access Point Rear Panel LAN Ethernet port with 10/100Mbps Fast Ethernet connections, connect this port to a switch/hub. RESET Press the “RESET” button for more than 5 seconds buttonto reset the settings back to factory default. Power Connect the DC Power Adapter plug to the AP’s power jack. Antenna Two external 3 dBi dipole antennas. 5
Summary of the content on the page No. 13
Side Panel The figure below shows the side panel of the IEEE 802.11b/g/n Wireless Broadband Router. Side Panel WPS Push this button to execute the Wi-Fi Protected Setup process. Hardware connections 6
Summary of the content on the page No. 14
Connect to the Switch/Hub/Router 1. Plug in one end of the RJ45 network cable to a Switch/Hub port, 2. Plug in the other end of the RJ45 network cable to the Wireless Access Point. Check the installation The LEDs of the Access Point are clearly visible and the status of the network link can be seen instantly: 1. With the power source on, once the device is connected, the Power, LAN and WLAN port LEDs will light up indicating a normal status. 2. If the LAN Port’s Link indicator does no
Summary of the content on the page No. 15
CONFIGURING THE WIRELESS LAN ACCESS POINT The Wireless Access Point has a Web GUI interface for easy configurations through a Web Browser. A network manager can manage, control and monitor the AP from the local LAN. This section indicates how to configure the AP to enable its functions. Login to the Wireless AP through WLAN Before configuring the Wireless AP through WLAN, make sure that the SSID, Channel and encryption settings are set properly. The default setting of the Wireless AP tha
Summary of the content on the page No. 16
Main Screen of the Access Point The screen will show the status of the AP when you login to the AP. There are seven main functions in the main screen: Wizard, Status, Basic Setting, IP Setting, Advanced Setting, Security and Tools. Wizard The setup wizard is provided as the part of the web configuration utility. Users can simply follow the step-by-step process to configure the Access Point in 4 easy steps. Click on the “Wizard” button and the following screen will appear. Please click
Summary of the content on the page No. 17
Step2: Set the SSID, Channel, Operation Band, 802.11 mode and Channel Width Please type the name of SSID and select the Channel, Operation Band, 802.11 mode and Channel Width. Then, click “Next” to continue. Step 3: Secure your Wireless Network The default security setting is set to NONE. There are four options: BEST (WPA2), BETTER (WPA), GOOD (WEP) and NONE. Please select the type of security and click “Next” to continue. 9
Summary of the content on the page No. 18
BEST (WPA2 Personal) Passphrase: The length should be at least 8 characters long and click “Next” to continue. 10
Summary of the content on the page No. 19
BETTER (WPA Personal) Passphrase: The length should be at least 8 characters long and click “Next” to continue. GOOD (WEP) Key Type: Select the key format from the drop-down list HEX or ASCII. Key Size: Select the level of encryption from the drop-down list. Wireless Security Password: Enter your WEP security key and click “Next” to continue. 11
Summary of the content on the page No. 20
Step 4: Save and Restart The Setup wizard is now completed. The new settings will be take effect after the Access Point has restarted. Please click “Restart” to save the new configuration and reboot the Access Point. Click “Exit” to quit without making any changes. Users also can go back to modify the setting by clicking “Back”. Status This page shows the following information. Firmware Version: Shows the current firmware version and released date code. LAN: Shows the Mac address,
