Summary of the content on the page No. 1
PN-TPC2W7A
User Guide
Version – 1
Summary of the content on the page No. 2
Getting Started Getting Started Introduction to PN-TPC2W7A The PN-TPC2W7A is a full-featured High Definition PC based upon Intel ® ® ® H67 architecture, and powered by an Intel G620 Pentium Dual- core CPU. Targeted for Commercial applications such as interactive digital signage, the PN-TPC2W7A has been optimized for reliable ® operation with Sharp PN-L series touch-screen displays. The PN- TPC2W7A includes the Sharp Pen Software™ application pre-installed on the hard disk. It also ha
Summary of the content on the page No. 3
Getting Started Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause h
Summary of the content on the page No. 4
Getting Started Specifications Chipset ® o Intel H67 Size o Mini-ITX form factor o Case: 7.5 x 7.4 x 1.75 Microprocessor support ® ® o Intel G620 2.6 GHz Pentium Dual-Core CPU Operating systems: ® ® ® o Supports Windows XP 32bit/64bit, Windows Vista ® ® 32bit/64bit, and Windows 7 32bit/64bit ® o Supports Linux o Windows 7 Pro installed Software Installed: ® o Sharp Pen Software™ Application ® ® o Microsoft Internet Explorer ® o Microsoft PowerPoint Viewer
Summary of the content on the page No. 5
Specifications Specifications (con’t) Onboard Audio o RealTek™ ALC888S High-Definition audio chip o Supports up to 8-channel (2/4/5.1/7.1-channel) o 8-Channel Audio Ports on Back Panel o Supports Jack-Sensing function (under Windows) o Support for S/PDIF Out Header (Internal) Green Function o Supports ACPI (Advanced Configuration and Power Interface) o Supports EuP Function o RTC timer to power-on the system o AC power failure recovery o Supports S0 (normal), S1 (power on s
Summary of the content on the page No. 6
Installation Mounting PN-TPC2W7A on Sharp PN-L Series Displays 1. Before mounting, make sure to turn off the monitor and remove the AC power. 2. Items needed Sharp PN-L Series Touch- Screen Display PN-TPC2W7A Mounting Plate AC Power Adapter 4 x M4 (0.7x10mm) screws 2 x M3 (0.5x5 mm) ® Phillips Screw Driver Figure 1 3. Attach the mounting plate There are 8 holes on the mounting plate, but only use 4 holes to match the monitor’s mounting holes de
Summary of the content on the page No. 7
Installation 4. Set the AC power adapter in place Place the AC power adapter into the holder on the right side of the mounting plate as in Figure 3. AC power cord faces downward and the DC power cord to the PN-TPC2W7A faces upward. Figure 3 5. Install the PN-TPC2W7A If you look at the right side of the PN-TPC2W7A before sliding it into the mounting plate as in Figure 4, there are two small slits near the edges on the PN-TPC2W7A and two small fingers on either side of AC
Summary of the content on the page No. 8
Installation There are two fingers on the left side of the mounting plate to catch the PN-TPC2W7A in place as shown in Figure 6, and they need to be tightened with two include M3 screws. Figure 6 6. Connect the HDMI video cable and the USB cable prior to turning on the PN- TPC2W7A. 7. Finish Plug in the DC power cord into the PN-TPC2W7A’s power connector as in Figure 7. Figure 7 7
Summary of the content on the page No. 9
Installation Rear Connector Layout Audio Port 2-Channel 4-Channel 5.1-Channel Blue Line-In Line-In Line-In Green Line-Out Front Speaker Out Front Speaker Out Pink Mic In Mic In Mic In Orange N/A N/A Center/Subwoofer Out Black N/A Rear Speaker Out Rear Speaker Out Grey N/A N/A N/A Audio Port 7.1-Channel Blue Line-In Green Front Speaker Out Pink Mic In Orange Center/Subwoofer Out Black Rear Sp
Summary of the content on the page No. 10
Installation Rear Connector Layout (con’t) 1. Power Connection (refer to the Rear Connector Layout on pg. 8) Use only the AC power adapter supplied with the system. Input: 100~240V AC 1.3A Output: 12V DC 7A Plug the 12V AC/DC adapter (as in the figure 1 above) to the PN- TPC2W7A’s power input jack (as in the figure 2). 2. Power Button This button will stay lit if the PN-TPC2W7A is powered on. If the PN-TPC2W7A doesn’t power up after the AC is connected, then press this butto
Summary of the content on the page No. 11
Support How to Recover to Factory Installed Condition 1. Before beginning Make sure that all the data including contents and programs you installed are backed up. If you are trying to recover from a bad HDD, please have a qualified technician runs diagnostics and replace defective components. If the unit is under warranty, please contact Sharp Customer Service. 2. Items needed Recovery DVD (comes with the unit) USB DVD Drive ® 3. Windows OS installation from Recovery DVD
Summary of the content on the page No. 12
Support Support & RMA Warranty service is available from a Sharp Authorized Service Center located in the United States. To receive repair handling instructions and to find the location of the nearest Sharp Authorized Service Center, please call Sharp toll free at 1-800-BE-SHARP (1-800-237-4277). If it is necessary to ship the Product for servicing, please be sure it is insured and packaged securely. Sharp shall not be responsible for lost, stolen or misdirected mail or for damage
Summary of the content on the page No. 13
12
