Eaton Electrical Char-Lynn 450 Series user manual

User manual for the device Eaton Electrical Char-Lynn 450 Series

Device: Eaton Electrical Char-Lynn 450 Series
Category: Power Supply
Manufacturer: Eaton Electrical
Size: 0.42 MB
Added : 5/30/2014
Number of pages: 12
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Eaton Electrical Char-Lynn 450 Series. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Eaton Electrical Char-Lynn 450 Series.

For your convenience

If looking through the Eaton Electrical Char-Lynn 450 Series user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Eaton Electrical Char-Lynn 450 Series on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Eaton Electrical Char-Lynn 450 Series to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Eaton Electrical Char-Lynn 450 Series User manual - Online PDF
Advertisement
« Page 1 of 12 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Eaton Electrical Char-Lynn 450 Series but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Eaton Electrical Char-Lynn 450 Series. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

®
No. 7-309
Char-Lynn August, 1999
Power Steering
Repair Information
110, 230 and 450 Series
001 002
Steering Control Units

Summary of the content on the page No. 2

110, 230, and 450 Series Steering Control Units 1 O-ring Groove Low Input Torque 12 2 Previous Manual Spring (4)/Spacer (2) Steering Check Valve Package 3 U V W O-ring Groove X 4 Y Standard Input Torque Z 11 Spring (6) 11 7 3 Package 11 6 23 22 9 3 9 8 5 13 14 13 17 15 18 19 31 16 30 10 Special Tools Available 600057-000 Spring Installation Tool 5422-000 12 Point Drive Socket ( 5/16 in.) — -001 64489-000 6 Point (E10) Torx Drive Socket ( 5/16 in.) — -002 See Note Below (lower right) Note: Curren

Summary of the content on the page No. 3

110, 230, and 450 Series Steering Control Units Tools required for disassembly and reassembly. — Screwdriver (102-152 mm [4 in. - 6 in.] long, x 3 mm [118 in.] wide flat blade). — 6 Point (E10) Drive part No. 64489-000* or 1/2 inch socket for current hex head cap screws. — Breaker bar wrench. — Torque wrench (30 Nm [275 lb-in] capacity). — Plastic hammer or rubber hammer. — 1/4 inch Hex key. — #10-24 machine screw, 38 mm [1-1/2 in.] long. — Needle nose pliers. The following tool is not necessar

Summary of the content on the page No. 4

110, 230, and 450 Series Steering Control Units Disassembly 2 Remove 5/6 in. cap screws and sealing washers, if used. Cleanliness is extremely important when repairing a steering control unit. Work in a clean area. Before disconnecting lines, 3 Remove end cap. clean port area of unit thoroughly. Use a wire brush to remove 4 Remove seal. foreign material and debris from around exterior joints of the unit. Seal Groove Although not all drawings show the unit in a vise, we recommend that t

Summary of the content on the page No. 5

110, 230, and 450 Series Steering Control Units Disassembly Low Input Old 3 Piece Teflon Seal Torque Ball Steering Manual Steering Check Valve (when applicable) Control Dust Seal Units Roll Pin Spring Early Units Built * Spacers (2) with these Parts Ball Retainer Plug Spring Ball Springs (4) Roll Pin Replacement Anti-Cavitation Valves * Teflon Seal (1 Piece) for Cylinder Ports Figure 5 Special Seal Gland Marked with Groove for Identification 12 Carefully remove anti-cavitation valves and manu

Summary of the content on the page No. 6

110, 230, and 450 Series Steering Control Units Disassembly Low Input Torque Spring/Spacer Package Standard Input Torque Bearing Race Needle Thrust Bearing Seal Figure 9 17 Remove two bearing races and needle thrust bearing and seal from Figure 11 spool and sleeve assembly. 19 Push pin from spool and sleeve assembly. 20 Push spool partially from control end of sleeve, then carefully remove centering springs from spool by hand (Figure 11). Low input torque unit uses four centering springs and tw

Summary of the content on the page No. 7

110, 230, and 450 Series Steering Control Units Disassembly/Reassembly 23 Screw a #10-24 machine screw into end of check ball seat. Then lift seat out of housing by pulling on screw with pliers. Spring Slot 24 Remove two seals from check valve seat. Assemble Input Shaft 25 Tip housing to remove check ball and check ball retainer. End First Input Shaft End 26 Do not remove any valves other than manual steering check valve assembly and anti-cavitation valve assembly. All other valves are fact

Summary of the content on the page No. 8

110, 230, and 450 Series Steering Control Units Disassembly 12 Place housing on clean lint free colth. Install 47,2 mm [1.86 in.] ID seal in housing (figure 18). spring slots of spool and sleeve. Position centering springs on bench so that extended edge is down and arched center section is together (figure 15). Next, with spring notches facing sleeve, insert one end of entire spring set into spring installation tool. 8 Compress extended end of centering spring set and push into spool and sle

Summary of the content on the page No. 9

110, 230, and 450 Series Steering Control Units Reassembly Roll Pin (2) Early Units Built * 40,00 mm with these Parts [1.575 in.] L Standard Torque Low Torque * O-ring Groove this Spring Screwdriver Teflon Seal Side -002 Unit — Retainer Plug Old Spacer Plate Dust Seal Ball has No O-ring Retaining Groove Ring Manual Steering Check Valve Seal Gland (when applicable) Bushing Roll Pin (1) Quad Ring 34,92 mm Seal Ball (2) [1.375 in.] L Seal 4,762 mm Seal [.1875 in.] OD Ball 6,35 mm [.250 in.] OD

Summary of the content on the page No. 10

110, 230, and 450 Series Steering Control Units Reassembly Seal washers are not used with 6 point (E10) or hex head screws and -002 end cap (-002 end cap does not have a o-ring groove). Seal Seal Groove this End Cap Side -002 Unit. See Note inside Front Cover Cap Screw (page 2) Seal Actual Item No. 5 Displacement Spacer 3 cm /r 3 Figure 24 [in /r] Length mm [in.] 45 [ 2.8] None 60 [ 3.6] None 23 Lubricate and install 72,6 mm [2.86 in.] ID seal in spacer plate or 75 [ 4.5] None gerotor (

Summary of the content on the page No. 11

110, 230, and 450 Series Steering Control Units Resassembly 6 4 ® Char-Lynn Eaton Corp. Hydraulics Div. Eden Prairie, MN 55344 1 2 000-0000-000 00/00/00 000-0000-000 7 3 5 Figure 27 28 Install 7 dry cap screws (and seal washers if applicable – see figure 26) in end cap. Pretighten screws to 17 Nm [150 lb-in], then torque screws to 25-30 Nm [225-275 lb-in] in sequence shown in figure 27. 11

Summary of the content on the page No. 12

110, 230, and 450 Series Steering Control Units ® Date Code How to Order Replacement Parts Char-Lynn 00 00 Product number Each Order Must Include the Following: Week of Last 1. Product Number 4. Part Number Eaton Corp. Hydraulics Div. Year 01 Number(s) Eden Prairie, MN 55344 Thru 52 of Year 2. Date Code 5. Quantity of Parts Product Number 3. Part Name 000 0000 000 For additional literature contact Eaton Corp. Hydraulics Product Line Product Engineering Division 15151 Highway 5 Eden Prairie,


Alternative user manuals
# User manual Category Download
1 Eaton Electrical 10640205 User manual Power Supply 3
2 Eaton Electrical 164201420B User manual Power Supply 1
3 Eaton Electrical 6000L(XL) User manual Power Supply 29
4 Eaton Electrical 9125 User manual Power Supply 6
5 Eaton Electrical 10000L(XL) User manual Power Supply 5
6 Eaton Electrical 9135 User manual Power Supply 87
7 Eaton Electrical 0800-7500 User manual Power Supply 1
8 Eaton Electrical 9170+ User manual Power Supply 3
9 Eaton Electrical 9120 User manual Power Supply 72
10 Eaton Electrical Char-Lynn 110 User manual Power Supply 1
11 Eaton Electrical APR48 User manual Power Supply 325
12 Eaton Electrical Char-Lynn 230 User manual Power Supply 0
13 Eaton Electrical Extended Battery Module (EBM) 9140 User manual Power Supply 4
14 Eaton Electrical IT-RSS User manual Power Supply 1
15 Eaton Electrical Powerware 5125 User manual Power Supply 20
16 Sony AC U50A User manual Power Supply 5
17 Sony AC LS1 User manual Power Supply 2
18 Sony NP-FM30 User manual Power Supply 35
19 Sony NP FX101 User manual Power Supply 1
20 Sony NH-AAA-DA User manual Power Supply 2