Summary of the content on the page No. 1
EPSON Stylus Pro 7000 series
-
Printer Specifications
roll paper cover paper set lever
ink cartridge
Printing
compartment
Printing method On-demand ink jet
Nozzle Black: 64 nozzles
control
configuration Color: 64 nozzles for each color: (cyan,
panel
magenta, yellow, light cyan, light magenta)
lower
cover
Resolution Maximum 1440 dpi × 720 dpi
Maximum 23.76 inches on 24-inch paper
printable width
Print direction Bidirectional or unidirectional
(user-selectable)
®
Control code ESC/P Raster
Summary of the content on the page No. 2
EPSON Stylus Pro 7000 series Paper Cut sheet paper specifications Size Dimensions in inches Dimensions in millimeters Thickness Super A1 24 × 36 610 × 914 3.15 to 19.7 mil (0.08 to 0.5 mm) US D 22 × 34 559 × 864 A1 23.4 × 33 594 × 841 B2 20.25 × 28.75 515 × 728 3.15 to 59 mil (0.08 to 1.5 mm) A2 16.5 × 23.4 420 × 594 Super A3/B* 13 × 19 329 × 483 US C 17 × 22 432 × 559 B3 14.3 × 20.25 364 × 515 US B (ledger)* 11 × 17 279 × 432 A3* 11.7 × 16.5 297 × 420 B4* 9.8 × 13.9 250 × 353 A4* 8.27 × 11.7 2
Summary of the content on the page No. 3
EPSON Stylus Pro 7000 series Ink Cartridges Interfaces Print yield Approximately 28 pages/A1 (720 dpi, 40% duty) Parallel interface Approximately 3,800 pages/A4 (360 dpi, 5% duty); print yield may vary, The built-in parallel interface supports compatibility and ECP depending on how often you run cleaning modes. cycles and how much you use the printer; Compatibility mode yield of the initial cartridge set is reduced because of ink charging Forward channel Cartridge life: Data format 8-bit par
Summary of the content on the page No. 4
EPSON Stylus Pro 7000 series ECP mode Drivers Transmission IEEE-1284 ECP mode mode ® ® Macintosh System 8.5.1 or later, Windows 95, Windows 98, Windows 2000, and Windows NT 4.0. Raster drivers are Adaptable 57-30360 Amphenol connector or ® ® standard. For Adobe PostScript support, use the optional connector equivalent ® EPSON RS-5100 Fiery X2 Printing System or a third-party Synchronization Refer to the IEEE-1284 specification software solution. Handshaking Refer to the IEEE-1284 specific
Summary of the content on the page No. 5
EPSON Stylus Pro 7000 series You can also use EPSON Photo Quality Ink Jet Paper, Photo Consumables and Accessories Paper, and Photo Quality Glossy Film in the EPSON Stylus Pro 7000 printer. Ink Cartridges EPSON Stylus Pro 7500 media Use these EPSON 110 ml ink cartridges before the expiration Paper type 24-inch roll Sheet sizes date on the package. Doubleweight Matte Paper S041385 — Glossy Paper Photo Weight S041388 — EPSON Stylus Pro 7000 graphic arts (dye-based) (22-inch roll) ink Premium S
Summary of the content on the page No. 6
EPSON Stylus Pro 7000 series Control Panel Lights and Messages Control Panel Normal printer operation Message/Light Explanation READY/ Operate light on Printer is ready to print. PRINTING/ Operate light Printer is receiving data. flashing INK DRY MIN/ Printer is paused to let ink dry. Wait for Pause light flashing the number of minutes shown. INK CHARGING Printer is charging the ink delivery %/Operate and system. Do not interrupt this process. Pause lights flashing TRANSPORT
Summary of the content on the page No. 7
EPSON Stylus Pro 7000 series Message/Light Explanation Response SelecType Menu Map Paper slipped and fed Reload paper, making PAPER NOT STRAIGHT/ into the printer at an sure the edges are ™ light angle. straight and aligned with Paper Out The following illustration shows the SelecType menus, along flashing both rows of holes. with the settings available for each one. PAPER OUT/ No paper is loaded. Load paper. Paper Out light Paper ran out. Remove any printouts or PRINTER STATUS TEST PR
Summary of the content on the page No. 8
EPSON Stylus Pro 7000 series 4. Press the Enter button. The status check prints. The Replacing an Ink Cartridge amount of ink left or component life is indicated as follows: E*****F = full (or full life remaining) When one of the Ink Out lights is flashing (and INK LOW is E**** F = 3/4 full (or 3/4 life remaining) displayed on the control panel), the corresponding cartridge is E*** F = 1/2 full (or 1/2 life remaining) almost out of ink. Make sure you have a replacement E** F = 1/4 full (or 1
Summary of the content on the page No. 9
EPSON Stylus Pro 7000 series If you’re using pigment ink (EPSON Stylus Pro 7500), 3. Examine the nozzle check pattern. It should look something shake the cartridge gently before installing it. like this: Each line should be complete, with no gaps in the dot pattern. If dots are missing, as shown below, you need to run a cleaning cycle. See the following section for instructions. 5. Hold the ink cartridge with the arrow mark face up and pointing to the rear of the printer. Then insert the in
Summary of the content on the page No. 10
EPSON Stylus Pro 7000 series 3. When the Pause light goes off, print a document or run a EPSON Stylus Pro 7000 Alignment Patterns nozzle check to confirm that the head is clean. 1 You may need to run the cleaning cycle several times to get 2 a clean nozzle check pattern. If the lines on the pattern still appear broken after several cleaning cycles, contact EPSON 3 for assistance. Always run a test print or nozzle check between cleaning 4 cycles. Otherwise, cleaning will not be effective. 5 6
Summary of the content on the page No. 11
EPSON Stylus Pro 7000 series 6. Select the row you chose in step 5 for each pattern (for 7. Check the control panel display. example line 8), then click Finish. ❏ For the EPSON Stylus Pro 7000, it shows #1 = 4, If you can’t make a consistent choice for the patterns as you indicating that row 4 is selected for pattern #1. look across the width of the paper, choose the average or ❏ For the EPSON Stylus Pro 7500, it shows #1 = 8, most frequent number. Then click the Realignment indicating tha
Summary of the content on the page No. 12
EPSON Stylus Pro 7000 series 6. If you’re using the stand, remove the wing screws and Moving the Printer on the Stand washers from the left and right sides, and keep them in a When you want to transport the printer a short distance, such safe place. as within the same building or facility, you can roll the printer on its casters. Caution: Do not roll the printer on angled or uneven surfaces. 1. Make sure that the power cord, interface cable, roll paper spindles and sheet media are removed,
