Summary of the content on the page No. 1
TM
DLP DATA DISPLAY
User’s Manual
MODEL :
VS-50XL50U
VS-50XLW50U
VS-50XLF50U
VS-50XLWF50U
VS-67XL50U-SN
( )
VS-67XL50U
SC-067XL50U
VS-67XLW50U-SN
( )
VS-67XLW50U
SC-067XL50U
VS-67XLF50U-SN
( )
VS-67XLF50U
SC-067XLF50U
VS-67XLWF50U-SN
( )
VS-67XLWF50U
SC-067XLF50U
Be sure to follow the directions below.
This product requires special installation to prevent
Warning:
toppling.
Please ask installation specialists for installation.
Don’t
Summary of the content on the page No. 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equi
Summary of the content on the page No. 3
Important safeguards Please read all these instructions regarding your 10. Power sources TM DLP data display and retain them for future This product should be operated only from reference. Follow all warnings and instructions the type of power source indicated on the TM marked on the DLP data display. marking label. If you are not sure of the type of power, please consult your appliance dealer 1. Read instructions or local power company. All the safety and operating instructions should be read b
Summary of the content on the page No. 4
WARNING: • for VS-50XLF50U, VS-50XLWF50U, VS- 67XLF50U, VS-67XLWF50U the temperature Unplug immediately if there is is lower than 10˚C (50˚F) or higher than 30˚C something wrong with your product. (86˚F) Do not operate if smoke, strange noise or odor comes out of your product. It might cause fire or CAUTION: electric shock. In this case, unplug immediately Battery replacement of the optional remote and contact your dealer. control R-XL50TX Never remove the cabinet. •Improper use may result in f
Summary of the content on the page No. 5
Specifications / Items sold separately Ω EN-5 Model VS-50XL50U VS-50XLW50U VS-50XLF50U VS-50XLWF50U VS-67XL50U VS-67XLW50U VS-67XLF50U VS-67XLWF50U 50 inches 50 inches 50 inches 50 inches 67 inches 67 inches 67 inches 67 inches Screen size (1015 x 761 mm) (1015 x 761 mm) (1015 x 761 mm) (1015 x 761 mm) (1359 x 1019 mm) (1359 x 1019 mm) (1359 x 1019 mm) (1359 x 1019 mm) RGB input Resolution: VGA – SXGA+, Horizontal: 31.5 to 78 kHz, Vertical: 49 to 85 Hz, signal supported Pixel clock rate: 25 to 1
Summary of the content on the page No. 6
Lamp replacement • VS-50XLW50U, VS-67XLW50U CAUTION Do not attempt to replace the lamp TM This product is equipped with the lamp to display images generated by DLP chip. This lamp is a consumable and it may lose its intensity or burn out during use. When the lamp intensity decreases, this product detects such decrease and switches the lamp to the built-in spare lamp automatically. (This function is called automatic lamp changer.) While the spare lamp is in use, a mark “ ” blinks on the screen. (
Summary of the content on the page No. 7
Lamp replacement (Only followed models : VS-50XL50U, VS-67XL50U) 1. Turn off the main power switch and 5. Insert a new lamp into the lamp unplug the power cord from the wall storage to the end. outlet. •Do not touch the glass envelope of the lamp with your fingers. The oil on your fingers Wait at least one hour for the lamp to cool may cause damage or explosion of the lamp. down. • Be sure to grip the handle with one hand and hold the lamp with the other hand to 2. Hold the handles by the finge
Summary of the content on the page No. 8
Troubleshooting Please check the following before contacting your dealer for service. Errors in signals are apt to be taken for problems in the product. Problems Remedies No image appears • Check the power cord is connected firmly. on the screen. • Check the correct input signals are selected for the terminals of the external devices. • Check the external devices are connected to the terminals firmly. • Check the external devices are turned on. • Check the appropriate signal is input from the ex
Summary of the content on the page No. 9
Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan Printed in Japan 871D431D50
