Summary of the content on the page No. 1
BARCO PROJECTION SYSTEMS
R9840170
R9840171
R9840176
Rugged Remote Control for ELM/SLM Projectors
1
Summary of the content on the page No. 2
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, October 2001. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visite Barco at the web : http://www.barco.com Printed in Belgium 2
Summary of the content on the page No. 3
Contents Contents Safety Instructions ................................................................................................ 4 Notice on Safety ...................................................................................................................................... 4 Installation Instructions............................................................................................................................ 4 Owner's Record ..........................................
Summary of the content on the page No. 4
Safety Instructions Safety Instructions Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment. These safety standards impose important requirements on the use of safety critical components, materials and isolation, in order to protect the user or operator against risk of electric shock and en
Summary of the content on the page No. 5
Safety Instructions FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
Summary of the content on the page No. 6
Safety Instructions 3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself. 4. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. 5. Never push objects of any kind into this product through cabinet slots as they may touc
Summary of the content on the page No. 7
Safety Instructions Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: 1. When the power cord or plug is damaged or frayed. 2. If liquid has been spilled into the equipment. 3. If the product has been exposed to rain or water. 4. If the product does not operate normally when the operating instructions are followed. Note : Adjust only those controls that are covered by the
Summary of the content on the page No. 8
General Information General Information Rugged Remote Control This Manual regroups several types of Rugged Remote Control Kits, depending on the type of rugged remote considered some information in this manual may become superfluous. R9840170: Wired Rugged Remote R9840171: Wireless Rugged Remote R9840176: Wireless Rugged Remote starters Kit (Wireless remote + single channel receiver) Upgrade Kits Upgrade to wireless RC: R9840175 Installation Manual Upgrade to Wireless RC: R5976350 Accessories
Summary of the content on the page No. 9
Contents Contents Contents of the Rugged Remote Control Case The Rugged Remote Control Case* contains following items: 1. Boxkit Magik: R593564 2. Boxkit fit rugged ctr puf: R821134 3. Rugged Remote Control : R763666 4. Battery charger: B557208 + EU Plug supplementary plugs US: B5572102 UK: B5572101 AUS: B5572104 5. SUBD9 Male/Male adaptor R821585 6. Lamp comms cable: Z34980143 7. Shoulder Strap : B400559 8. Installation Manual : R5976251 1 2 4. 3. 5. 6. 7. 8.
Summary of the content on the page No. 10
Description & Specifications Description Application The Barco Rugged Remote Control enables the control of the Barco ELM and SLM series DLP Projectors and the Barco 6000 series LCD Projectors. The Rugged Remote Control allows following functions: Remote Mode:The Remote Control sends actions to and reads information from the projector Lamp Read Mode:The Remote Control reads information stored in the lamp information Module. Software compatibility G5 SLM: Sofware version V1.05 and higher R6 SLM:
Summary of the content on the page No. 11
Description & Specififcations Charger Input range : 100-240V (autoranging) 47-63Hz 400 mA Output: 15V DC/1A Input/Output Signals A image 3 B CTRL 3 CTRL 4 Two Way Hardwired Remote (CTRL 3) Lamp Info Module (CTRL 4) PUSH W Q J L D S ’ 1 * $ $7 ’ $ $7 ’ Fixed rate: 57600 baud Cable type: XLR connection, twisted pair Cable type: supplied Serial interface RS 232/422 Serial interface A (image 3) Selectable modes : - RS 422 T: RS422 terminated. - RS
Summary of the content on the page No. 12
+ Description & Specififcations Keypad F1,F2,F3,F4,F5 B A E F C D Key Name Function (when not specified : idem RCU) F1,F2,F3,F4,F5 Function Keys Function keys (determined by the projector) + A Browse Keys up/down left/right B Command Keys idem RCU C Validation keys EXIT ENTER D Numeric keys LED TEXT ON indicaton (Red) E LED PAUSE indication (Yellow) F 12 - -
Summary of the content on the page No. 13
Description & Specififcations Wireless Base Weight: 0.3 kg (0.6 lbs) Communication port A Serial interface C Selectable modes with switch B : - RS 422 T: RS422 terminated. - RS 422 NT: RS422 Not Terminated - RS 232 In order to set up a communication link the mode setting on the base must match the setting within the projector Termination resistor = 120 Ohms LED D: when lit: power present BD AC image 1 13
Summary of the content on the page No. 14
Installation Setup Installation setup Power Connections The charger The charger can be fitted with the 4 supplied power plugs: 1. 2. 1. Australia 2. US/Japan 3. Europe 4. UK 3. 4. Changing the plug 1. Pull the plug to be changed upwards untill it is completely removed from the charger (Image 1) 2. Place the plug to be mounted on the charger and guide it downwards by using the guiding slots (Image 1 & 2) 3. Push the plug downwards untill it clicks and is locked into the charger (Image 3) 4
Summary of the content on the page No. 15
Installation Setup Power ON switch The ON/OFF switch A is located on the right side of the Rugged Remote Control near the DC power plug (image 3). Remark: The Remote Control can also be supplied with the charger permanently connected. A image 3 Supplying the Wireless Base The wireless base is supplied via the projector. The connection needs a standard serial cable linking the 'COMM PORT' of the projector to the 'COMM PORT' of the Wireless Base. The supplied voltage depends on the type of projec
Summary of the content on the page No. 16
Installation Setup Charging the batteries The batteries are trickle charged whenever the XLR connection with a powered projector is made or when the charger is connected. Charging is required whenever the batteries are low, the status (ACT/LOW) of the batteries can be seen on the main menu (menu 1) or in the diagnosis menu (see " Installation Settings "). remark: The delivered batteries are not charged. The batteries may only be used after being charged, it takes about 30 hours to fully
Summary of the content on the page No. 17
Installation Setup Changing the batteries The expected life of the batteries is about approximatively 1000 charge and discharge cycles. When replacing the batteries, all batteries should be replaced at the same time. CAUTION Risk of explosion if the batteries are replaced by an incorrect type Dispose of used batteries according to the instructions To change the batteries follow next procedure: 1. Turn the remote off and remove all the cables 2. Turn the locking screw counterclockwise to free th
Summary of the content on the page No. 18
Configuration Setup Configuration Setup Remote Mode Performing Remote Control of the projector The connection of the Rugged Remote Control to a projector uses a standard twisted pair cable with XLR connectors at each extremity (not supplied). The baudrate is fixed at 57600 baud. Image 1 gives an example of a Remote Control connected to a G5 SLM Projector. Image 1 How to Connect 1. Plug the cable in the Remote connector labeled CTRL3 "Two way hardwired remote". 2. Plug the other extremity in
Summary of the content on the page No. 19
Configuration Setup Lamp Read Mode Reading the Lamp The Lamp Read Mode requires a connection between the lamp unit and the Remote Control using the supplied lamp cable (Z34980143). Reading the lamp is only possible for BARCO ELM and SLM projectors. How to Connect 1. Plug the cable in the remote control connector labeled CTRL4 "Lamp Info Module". 2. Plug the other extremity in the Lamp Unit connector. WARNING To avoid burns always let cool down the lamp before handling it . 19
Summary of the content on the page No. 20
Configuration Setup RS232/422 Communication The Remote Control allows RS232/422 serial mode communication with the projector. This is used for software upgrade of the Rugged Remote Control or to perform a remote control of the projector (instead of using the CTRL3 Two way hardwired remote). Different baudrate(baud)settings: - 9600 - 19200 - 38400 - 57600 image1 - 115200 B See 'Menu Setup' for setting procedure. To select the different serial modes use switch B (image 1). RS232/422 remote con
