Summary of the content on the page No. 1
Installation Instructions
Quick Reference
30" Freestanding
Table of Contents:
Pages
Gas Range
Before you start
2
with standard clean oven
Product dimensions
2
Cabinet dimensions/requirements
2
Gas supply requirements
3
Installation steps
4 - 6
Gas conversions
7 - 8
Back cover If range does not operate
If you need assistance/service
Back cover
Back cover Moving the range
If you need assistance:
Check your Use and Care Guide for a toll-free number to call or call the
dealer from whom you purc
Summary of the content on the page No. 2
Before you start... Product dimensions Your safety and the safety of Proper gas supply connection must be others are very important. available. See “Gas We have provided many important safety supply requirements,” message in this manual and on your Page 3. appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and 26-3/4" depth others. with handle All safety messages will be preceded by the saf
Summary of the content on the page No. 3
Tools needed: level Materials required: • gas line shutoff valve • 1/2" male pipe thread nipple for connection to pressure regulator hand or 3/8" drive gloves • L.P. gas-resistant pipe-joint compound electric drill Phillips ratchet screwdriver • AGA or CSA design-certified flexible metal appliance connector (4-5 feet) or rigid gas supply line as needed • Insulated pad or 1/4" plywood if range is installed concrete/ceramic floors: over carpeting wood floor: 3/16" carbide-tipped masonry 1/8" d
Summary of the content on the page No. 4
Check cooktop E burners for proper flame Make proper Remove shipping D gas connection A material. Remove oven racks and parts package. Install anti- B tip bracket Secure range C with anti-tip Level range bracket C Close broiler D door Check burner E operation Installation steps Preparation A 1.Put on safety glasses and gloves. Do Not use oven door handle to lift or move the range. WARNING Excessive Weight Hazard Use two or more people to move and install range. cardboard Failure to follow thi
Summary of the content on the page No. 5
Operating position C Before moving range across floor, check that range is still on cardboard shipping base to 6.Making sure the protect floor covering. anti-tip bracket is installed: anti-tip • Look for the bracket front leveling leg anti-tip bracket range foot securely attached to floor. • Slide range back so rear range foot is under anti-tip bracket. 8.Place rack in oven. Place level on rack, first side to side; then front to back. If range is not level, pull range forward until rear le
Summary of the content on the page No. 6
Check operation E You have just finished installing Check operation of cooktop Check operation of oven/broil burner your new range. To get the most efficient use from your range, read your Use & Care Guide. 19.Open broiler drawer. Keep Installation Instructions and Guide close to range for easy reference. The instructions will make installing the range in another home as easy as the first installation. 18.Push in and turn each surface unit control knob to “LITE” position. The flame should light
Summary of the content on the page No. 7
Gas conversions Remove and replace Gas conversions (from Natural gas to L.P. gas; or orifice spuds orifice spuds. Natural gas conversion from L.P. gas to Natural gas) must be done by a qualified installer. 1.Check that the manual shutoff valve in the notches gas supply line has been turned off. WARNING L.P. NAT Note: Burner tube and brackets not shown. gas manifold burner screw Fire Hazard pressure regulator Shut off gas supply line valve. Make all conversions before turning gas L.R. L.F. R.R. R
Summary of the content on the page No. 8
Remove and replace orifice spuds orifice spuds. notches NAT L.P. Note: Burner tube and brackets not shown. gas manifold L.F. R.R. R.F. L.R. 5.Locate Natural gas orifice spuds in literature package included with the range. All Natural gas spuds are stamped with “145”. Remove L.P. gas orifice spuds using a 3/8" combination wrench. Install Natural gas orifice spuds to replace the L.P. gas orifice spuds. Place L.P. gas orifice spuds in plastic parts bag for future use and keep with literature packag
Summary of the content on the page No. 9
If range does not operate: Moving the range: Check that gas line is turned on. When moving range, slide range onto cardboard See Use and Care Guide for troubleshooting list. or hardboard to prevent damaging the floor WARNING covering. If you need assistance: If removing the range is necessary for cleaning If you have questions about operating, cleaning or maintenance: or maintaining your range: 1. Shut off the gas supply to the range. Refer to Use and Care Guide. 2. If necessary, slide ran
