Summary of the content on the page No. 1
Elongate Model G60 for openings 45” to 60” wide
Use 1 optional 24” extension (Model G24) when opening is 5’ to 7’ wide
Use 2 optional 24” extension (Model G24) when opening is 7’ to 9’ wide
Use 3 optional 24” extension (Model G24) when opening is 9’ to 11' wide
Use 4 optional 24” extension (Model G24) when opening is 11' to 13’ wide
Maximum 4 extensions per gate.
User Guide
~s#lq-J+J E
.+ .k ej$ :Irc;’
_*
I
Summary of the content on the page No. 2
FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE This gate is designed for children from 6 months to 36 months. Since each child’s skills develop at different ages, these age parameters should be monitored against your child’s own development. Intended for use with children Do not use if any part of gate is from 6 months through 36 broken or missing. months. This product will not neccessarily Check and tighten all hardware prevent all accidents. Never leave and mountings re
Summary of the content on the page No. 3
Locking Side Hardware Hinge Side Hardware 2 Hinge bottoms (c) 2 Locking latches (e) If 0 2 Hinge spindles with locknuts (I) 2 Locking latch brackets (f) P I!!8 I 2 Springs (k) 1 Bottom latch spindle 6 1/4" (m) 2 Hinge caps (d) b Latch spindle Hinge already fitted (q) General Hardware ) 1 Main gate section 8 Wood screws (g) with door opening (n) 1 Protective plastic cover (h) c 4 Expansion screw sockets (i) u 1 Second Section (o) 4 Expansion screws (j) f 1 Stabilizing foot (p) 1 Hinge side templa
Summary of the content on the page No. 4
important: Gate must be installed in a struc- turally sound opening. Hinge side of gate must be mounted to a rigid surface. Ensure mounting surface (wall, door frame, stairpost etc.) is strong, rigid and has an even surface. If using gate on a stairway it must be placed either on top stair or on lowest stair at bot- tom. If using on a top step, use of an optional step plate is recommended to reduce tripping potential. Mounting Hinge Side Screws provided are for mounting directly into wood. If mo
Summary of the content on the page No. 5
Screw hinge spindles (I) into top and bottom rails of second section (o) until they are extended equally. These will be adjusted to correct length at a later stage so do not tighten. Mounting Locking Side Screws provided are for mounting directly into wood. If mounting into brick, drywall or other surfaces, use appropriate hard- ware. If installing into hardwood (i.e. oak) drilling a pilot hole may be necessary. Hold template (b) against mounting surface in line with opposite hinges, making sure
Summary of the content on the page No. 6
The correct width will be reached by adjus- ting gate sections and all four corner spind- les. Each spindle adjusts individually and may be extended to varying lengths to allow for molding, uneven walls, etc. Spindles may be extended a minimum af 1” but not more than 4” on each side. Adjust gate sections until gate is approxi- mately right width and adjustment holes are aligned top and bottom. Sections should fit without any distance between bars. Gate sections must not be extended any further t
Summary of the content on the page No. 7
Center gate in opening. Gaps on each side should be equal. Place hinge spindles (I) over hinge bottom posts (c), dropping them into place. Adjust latch spindles out until they fit securely into the two locking brackets. Latch spindles must be adjusted so they click under locking latch when in closed position. Space between end of gate and mounting surface should be no less than 1” and not more than 4” on each side. Check that gate can be easily opened and closed without catching. Place a spring
Summary of the content on the page No. 8
A protective plastic cover (h) is provided for the top latch spindle. Cut cover, remove latch spindle and put cover on. Return spindle and adjust to correct length. 8
Summary of the content on the page No. 9
To open walk through section, press down on top locking latch, lift walk through section so hinge is raised (a), and slide out of bracket. Note: The gate should always be in locked position. If gate is open and excessive pressure is applied, hinge posts are desig- ned to break to prevent structural dama- ge. To close gate, lift walk through section and position safety foot onto frame, making sure hinge has dropped down (b). To lock gate, latch spindle at top must click under locking latch. Safet
Summary of the content on the page No. 10
KIDCO LIMITED WARRANTY Your KidCo product is warranted to be free from manufacturing defects for a period of one year from date of purchase under normal use and in compliance with the operating instruc- tions. This warranty extends only to the original retail purchaser and is only valid when suppli- ed with proof of purchase. KidCo will either repair, or at our option replace, free of charge, any parts necessary to correct defects in material or workmanship during the warranty period. This warra
