Summary of the content on the page No. 1
C1642M-A FT85011.book Page 1 Wednesday, January 19, 2005 12:46 PM
INST ALLA TION
FT85011/FR85011
Fiber Transmitter
and Receiver
®
Single-Channel Digitally Encoded Video
with Bidirectional Data
C1642M-A (1/05)
Summary of the content on the page No. 2
C1642M-A FT85011.book Page 2 Wednesday, January 19, 2005 12:46 PM
Summary of the content on the page No. 3
C1642M-A FT85011.book Page 3 Wednesday, January 19, 2005 12:46 PM Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Summary of the content on the page No. 4
C1642M-A FT85011.book Page 4 Wednesday, January 19, 2005 12:46 PM Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital devic
Summary of the content on the page No. 5
C1642M-A FT85011.book Page 5 Wednesday, January 19, 2005 12:46 PM Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
Summary of the content on the page No. 6
C1642M-A FT85011.book Page 6 Wednesday, January 19, 2005 12:46 PM CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the oper- ating instructions unless you are qualified to do so. The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present CAUTION: within this unit. RISK O
Summary of the content on the page No. 7
C1642M-A FT85011.book Page 7 Wednesday, January 19, 2005 12:46 PM Product Overview DESCRIPTION The FT85011/FR85011 fiber transmitter and receiver provide the ability to transmit one unidirectional composite video channel and one bidirectional data channel over one optical fiber. In addition, ® patent-pending technology provides the solution for allowing Coaxitron pan/tilt/zoom (PTZ) control data to be transmitted the full distance of the fiber (up to 6 km for multimode fiber and up
Summary of the content on the page No. 8
C1642M-A FT85011.book Page 8 Wednesday, January 19, 2005 12:46 PM • Standalone and rack-mountable modular design • LED indicators for monitoring of signal status, data activity, and operating power NOTES: • The FT85011 transmitter/FR85011 receiver is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825-1 Edition 1.2, 2001-08. • In addition to compatibility with the FT85011 transmitter, the FR85011 receiver is also ™
Summary of the content on the page No. 9
C1642M-A FT85011.book Page 9 Wednesday, January 19, 2005 12:46 PM MODELS The FT85011/FR85011 fiber transmitter and receiver consist of the following series of models: Multimode Models: FT85011MSTR Single-channel fiber optic video transmitter/data transceiver; multimode, ST connector FR85011MSTR Single-channel fiber optic video receiver/data transceiver; multimode, ST connector Single-Mode Models: FT85011SSTR Single-channel fiber optic video transmitter/data transceiver; single- mode,
Summary of the content on the page No. 10
C1642M-A FT85011.book Page 10 Wednesday, January 19, 2005 12:46 PM FRONT PANEL The front panel of the FT85011 transmitter and the FR85011 receiver provides LED indicators that allow you to monitor data activity, signal status, and operating power (refer to Figure 2). Tx Tx Rx Rx 1 FT85011 FR85011 RECEIVER TRANSMITTER Figure 2. Front Panel of FT85011 Transmitter and FR85011 Receiver DATA TX LED DATA RX LED VIDEO PRESENT LED CARRIER DETECT LE
Summary of the content on the page No. 11
0 0 C1642M-A FT85011.book Page 11 Wednesday, January 19, 2005 12:46 PM REAR PANEL All connections to the FT85011 transmitter and FR85011 receiver are made to the rear panel of the modules (refer to Figure 3). 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 GND GND 2 3 2 3 1 4 1 4 5 5 9 6 9 6 8 7 8 7 11 FT85011 FR85011 TRANSMITTER RECEIVER Figure 3. Rear Panel of FT85011 Transmitter and FR85011 Receiver RACK POWER/ALARM CONNECTOR, 4-pin connector for p
Summary of the content on the page No. 12
0 0 C1642M-A FT85011.book Page 12 Wednesday, January 19, 2005 12:46 PM Installation PACKAGE CONTENTS The following items are supplied: • With the FT85011 transmitter: 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC input, 12 VDC output 1Wall clip with two 4-40 x .250-inch Phillips pan head screws with lock washers (for attachment of single module to wall) 1 FT85011/FR85011 Fiber Transmitte
Summary of the content on the page No. 13
C1642M-A FT85011.book Page 13 Wednesday, January 19, 2005 12:46 PM With the FT85011 transmitter/FR85011 receiver powered off, set the Data Selection switch to the required data communication using a small screwdriver. Refer to Table A for data commu- nication switch settings. Table A. Data Communication Switch Settings Data Communication Switch Setting RS-232 0 (default setting) RS-422 1 RS-485 2-Wire 2 RS-485 4-Wire 3 Manchester/Bi-Phase 4 Coaxitron 5 Not used 6-9 Note the f
Summary of the content on the page No. 14
C1642M-A FT85011.book Page 14 Wednesday, January 19, 2005 12:46 PM MOUNTING THE TRANSMITTER/RECEIVER INTO A RACK Optional fiber rack mount chassis, which can be mounted into an industry-standard 19-inch (48.26 cm) equipment rack, are designed for installation of multiple modules: • The RK5000PS-3U fiber rack mount chassis provides 12 module slots and a power supply. • The RK5000-3U fiber rack mount chassis provides 14 module slots (a power supply is not included). Power to the mo
Summary of the content on the page No. 15
C1642M-A FT85011.book Page 15 Wednesday, January 19, 2005 12:46 PM UPPER FLANGE VERTICAL MOUNTING HOLE (2) HORIZONTAL TRANSMITTER/ MOUNTING HOLE (2) RECEIVER LOWER FLANGE SCREW, PHILLIPS WALL CLIP PAN HEAD WITH LOCK WASHER (2) Figure 5. Mounting the FT85011 Transmitter/FR85011 Receiver Using the Wall Clip C1642M-A (1/05) 15
Summary of the content on the page No. 16
0 C1642M-A FT85011.book Page 16 Wednesday, January 19, 2005 12:46 PM CONNECTIONS Connections to the FT85011 transmitter and the FR85011 receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTE: A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a standalone module. A 12 VDC power supply is provided. If a 24 VAC power supply is used, the power supply must be a Listed Direct Plug-In Power Unit
Summary of the content on the page No. 17
C1642M-A FT85011.book Page 17 Wednesday, January 19, 2005 12:46 PM Table B. Data Connector Pin Assignments Pin RS-485 RS-485 Number RS-232 RS-422 2-Wire 4-Wire Manchester Bi-Phase 1— Out+ In+/Out+ Out+ — — 2— Out- In-/Out- Out- — — 3— In+ — In+ In+ (W) In+ 4— In- — In- In- (B) In- 5In — — — — — 6 Out — — — — — 7— —— — Out+ (W) Out+ 8— —— — Out- (B) Out- 9 Ground —* —* —* Shield Shield *Ground may be required based on conditions of installation. Refer to the current version of E
Summary of the content on the page No. 18
0 0 C1642M-A FT85011.book Page 18 Wednesday, January 19, 2005 12:46 PM FR85011 RECEIVER – DEVICE A DATA CONNECTOR 1 RS-232 DATA SELECTION 2 3 2 3 RS-232 1 4 RX 4 5 5 (RX) DATA IN TX 9 6 6 (TX) DATA OUT 8 7 GND 7 8 GND RS-232 DATA CONNECTIONS BETWEEN DEVICE A AND FR85011 RECEIVER FT85011 TRANSMITTER – DEVICE B DATA CONNECTOR 1 RS-232 DATA SELECTION 2 3 2 3 RS-232 1 4 RX 4 5 5 (RX) DATA IN TX 9 6 6 (TX) DATA OUT 8 7 GND 7 8 GND RS-232 DATA CONNECTIONS BETWEEN DEVICE B AND FT85011 TRANS
Summary of the content on the page No. 19
0 0 C1642M-A FT85011.book Page 19 Wednesday, January 19, 2005 12:46 PM FR85011 RECEIVER – DEVICE A DATA CONNECTOR RS-422 RX+ 1 (TX+) DATA OUT+ RS-422 RX- DATA SELECTION 2 (TX-) DATA OUT- TX+ 3 (RX+) DATA IN+ 2 3 1 4 TX- 4 (RX-) DATA IN- 5 5 9 6 6 8 7 7 8 GND RS-422 DATA CONNECTIONS BETWEEN DEVICE A AND FR85011 RECEIVER FT85011 TRANSMITTER – DEVICE B DATA CONNECTOR RS-422 RX+ 1 (TX+) DATA OUT+ RS-422 RX- DATA SELECTION 2 (TX-) DATA OUT- TX+ 3 (RX+) DATA IN+ 2 3 1 4 TX- 4 (RX-) DAT
Summary of the content on the page No. 20
0 0 C1642M-A FT85011.book Page 20 Wednesday, January 19, 2005 12:46 PM FR85011 RECEIVER – RS-485 DEVICE A DATA CONNECTOR 2-WIRE RX+/TX+ 1 (TX+/RX+) DATA OUT+/DATA IN+ RS-485 2-WIRE DATA SELECTION RX-- /TX 2 (TX-/RX-) DATA OUT-/DATA IN- 3 2 3 4 1 4 5 5 9 6 6 8 7 7 8 GND RS-485 2-WIRE DATA CONNECTIONS BETWEEN DEVICE A AND FR85011 RECEIVER FT85011 TRANSMITTER – RS-485 DEVICE B DATA CONNECTOR 2-WIRE RX+/TX+ 1 (TX+/RX+) DATA OUT+/DATA IN+ RS-485 2-WIRE DATA SELECTION RX-- /TX 2 (TX-/RX-)
