Summary of the content on the page No. 1
®
DD08 Series
®
Intercept
Dome Drive
Installation/
Operation Manual
C416M-C (1/98)
U
® L
LISTED
Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 • DataFAX (1-559) 292-0435
Summary of the content on the page No. 2
CONTENTS Section Page 1.0 GENERAL ..................................................................................................5 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 5 1.2 UNPACKING INSTRUCTIONS .......................................................... 6 1.3 RECOMMENDED TOOLS ................................................................. 6 2.0 DESCRIPTION ........................................................................................... 7 2.1 M
Summary of the content on the page No. 3
REVISION HISTORY Manual # Date Comments C416M 9/94 Original version. C416M-A 6/95 Revised to incorporate exploded view diagram and BOM changes as per ECO# 94-470; Incorporated white “type E” back box availability; Included hardwire system wiring diagram information. 6/23/95 Addendum. Changed back box wiring diagrams to show 2 A FUS2 fuse as per ECO# 95-063. C416M-B 9/20/95 Manual revised to include new sound quieting model information, updated hardwire system wiring diagram and related list of m
Summary of the content on the page No. 4
(This page intentionally left blank.) 4 Pelco Manual C416M-C (1/98)
Summary of the content on the page No. 5
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco
Summary of the content on the page No. 6
1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. Be sure to save the shipping carton and any inserts. They are the safest material in which to make future shipments. If an item appears to have been damaged in shipment, replace it properly in its carton and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replace- ment. (International customers fax 1-559-348-1120 for authorization and instruc- tions.) If an item needs to be returned to the factory for repair, consu
Summary of the content on the page No. 7
2.0 DESCRIPTION ® The DD08 Series of dome drives is part of the IDS08 Intercept Series of domes. The IDS08 Series is an integral system that includes a back box (BB08), dome drive (DD08), dome receiver/driver (DRD08), and imager/optics package (IOP08). This manual covers the DD08 Series of dome drives. For installation and operation instructions for the back box, refer to manual C456M-D; for the dome receiver/ driver, refer to C466M-E; and for the imager/optics package, refer to C1441M-C. 2.1
Summary of the content on the page No. 8
3.0 INSTALLATION Proceed with the installation of the dome drive after you have installed the back box. 1. Refer to Figure 6 and remove the shipping bracket (item 37). 2. Refer to the manual for the receiver/driver and set the jumpers and switches as required for your application. 3. DD08C2L and DD08E2L Models Only - The dome drives are capable of 360° rotation. However, pan limit stops have been installed at the factory on the pan gear that limit the rotation to 355°. If you prefer 360° rotati
Summary of the content on the page No. 9
BACK BOX HAIRPIN CLIP LATCH HAIRPIN GUIDE PIN GUIDE PIN CLIP LATCH 25-PIN CONNECTOR DOME DRIVE UPPER BRACKET 25-PIN CONNECTOR LATCH PIN LATCH PIN BUSHING BUSHING Figure 2. Back Box and Dome Drive Components Pelco Manual C416M-C (1/98) 9
Summary of the content on the page No. 10
7. Turn on the power switch inside the back box. In about 15 seconds, the unit will begin to move and go through its start-up routine. 8. Refer to the manual for the camera/lens to set the switches on the camera as required for your application. 9. DD08C2L and DD08E2L Models Only - If you removed the pan limit stops earlier, skip this step. NOTE: The tilt limit stops are not To adjust the pan limit stops: adjustable. a. Pan the unit to the desired left position. b. Turn off the power switch insi
Summary of the content on the page No. 11
4.0 MAINTENANCE Regularly scheduled maintenance will prolong the operational life and appearance of the equipment. Clean the dome with a nonabrasive cleaning cloth and antistatic cleaner that is safe for use on acrylic plastic. Do not use kerosene or similar substances that can scratch the surface. The dome drive should also be inspected and any dust and debris blown off. Pay special attention to the gear drives. After removing dust and debris a film of silicone lubricant should be applied to t
Summary of the content on the page No. 12
5.0 WIRING DIAGRAMS Figure 3. 24 VAC Back Box Wiring Diagram 12 Pelco Manual C416M-C (1/98)
Summary of the content on the page No. 13
Figure 4. 120 VAC Back Box Wiring Diagram Pelco Manual C416M-C (1/98) 13
Summary of the content on the page No. 14
Figure 5. Dome Drive Wiring Diagram 14 Pelco Manual C416M-C (1/98)
Summary of the content on the page No. 15
6.0 EXPLODED ASSEMBLY DIAGRAMS 1 2 3 4 8 5 54 6 10 7 11 12 13 48 24 14 47 23 39 22 46 25 21 9 35 45 44 53 43 42 41 15 35 40 38 19 28 49 27 29 31 30 26 34 36 20 33 16 17 REMOVE BEFORE 18 32 OPERATING 37 Figure 6. DD08 Series Dome Drive Exploded Assembly Diagram (Mechanical) Pelco Manual C416M-C (1/98) 15
Summary of the content on the page No. 16
Table A. DD08 Series Dome Drive Exploded Assembly Parts List (Mechanical) Item Quantity Description Part Number 1 2 Bushing 80010004 2 2 Push nut 80010011 3 1 Upper drive mount bracket 8004034COMP 4 2 Dome drive latch pin 8004145COMP 5 1 Slip ring, 10-lead SR10-1 6 1 Spindle 8004004COMP 7 3 Pan limit stop (except DD08E3L model) 80010050 8 1 25-position connector receptacle CON10J025Z41T 9 1 Pan limit pin bracket (except DD08E3L model) 8004013COMP 10 1 Pan gear 80010012 11 4 Thrust wash
Summary of the content on the page No. 17
Figure 7. DD08 Series Dome Drive Exploded Assembly Diagram (Hardware) Pelco Manual C416M-C (1/98) 17
Summary of the content on the page No. 18
Table B. DD08 Series Dome Drive Exploded Assembly Parts List (Hardware) Item Quantity Description Part Number A 2 Screw, 8-32 x 3/8", hex head (except DD08E3L) ZH8-32X.375HMSS B Allen set screw, 8-32 x 1/4", black ZH8-32X.250S 1 DD08E3L only 2 DD08C2L and DD08E2L only C 4 Allen set screw, 8-32 x 3/16", black ZH8-32X.187S D 2 Spacer, 1/4" hex x 1/2" long, 6-32 tapped SPA8423 E 2 Screw, 1/4-20 x 1" flat head, Phillips ZH1/420X1.00SFS F 5 Screw, 6-32 x 3/8" pan head, Phillips ZH6-32X.375SPP G 3 Sc
Summary of the content on the page No. 19
7.0 SPECIFICATIONS MECHANICAL Pan Movement in horizontal plane: DD08C2L/ DD08E2L models: 0-355° with pan limit stops 360° without pan limit stops DD08E3L model: 360° Tilt: -90° movement from horizontal plane Pan and Tilt Speeds: The following speeds are available and pre-selected by cus- tomer at time of order: Dome Drive Type Pan Speed Tilt Speed DD08C2L 24°/sec ± 1° 12°/sec ±.5° DD08E2L 24°/sec ± 1° 12°/sec ±.5° DD08E3L Variable (0 – 200°/sec) 0–40°/sec ±.5° Motors: Synchronous, continuous d
Summary of the content on the page No. 20
8.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment. Exceptions to this warranty are as noted below: • Two (2) years on all standard motorized and fixed focal length lenses. ® ® • Two (2) years on Legacy , Intercept , PV1000 Series, CM6700/CM8500/CM9500/ CM9750/CM9760 Matrix, Spectra™, DF5 Series and DF8 Fixed Dome products. • Two (2) years o
