Summary of the content on the page No. 1
Dell™ PowerEdge™
R815 Systems
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Dell™ PowerEdge™ R815 Systems Getting Started With Your System Regulatory Model E05S series
Summary of the content on the page No. 4
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved. Reproduction of these materials in any manner w
Summary of the content on the page No. 5
Installation and Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the system. Unpacking the System Unpack your system and identify each item. Assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your system. Getting Started With Your System 3
Summary of the content on the page No. 6
Optional – Connecting the Keyboard, Mouse, and Monitor Connect the keyboard, mouse, and monitor (optional). The connectors on the back of your system have icons indicating which cable to plug into each connector. Be sure to tighten the screws (if any) on the monitor’s cable connector. Connecting the Power Cable(s) Connect the system’s power cable(s) to the system and, if a monitor is used, connect the monitor’s power cable to the monitor. 4 Getting Started With Your System
Summary of the content on the page No. 7
Securing the Power Cable(s) Bend the system power cable into a loop as shown in the illustration and secure the cable to the bracket using the provided strap. Plug the other end of the power cable into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). Turning On the System Press the power button on the system and the monitor. The power indicators should light. Getting Started With Your System 5
Summary of the content on the page No. 8
Installing the Optional Bezel Install the bezel (optional). Complete the Operating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the installation and configuration documentation for your operating system. Be sure the operating system is installed before installing hardware or software not purchased with the system. Supported Operating Systems ® ® � Micro
Summary of the content on the page No. 9
� Microsoft Windows Server 2008 R2 Standard, Enterprise, and Datacenter (x64) editions with SP2 � Microsoft Windows HPC Server 2008 (x64) � Microsoft Windows HPC Server 2008 (x64) with SP2 � Microsoft Windows HPC Serv er 2008 R2 (x64) with SP2 � Microsoft Windows Server 2003 R2 Standard and Enterprise (x86) editions � Microsoft Windows Server 2003 R2 Standard, Enterprise, and Datacentre (x64) editions � Microsoft Windows Essential Business Server Standard and Premium (x64) editions � Micro
Summary of the content on the page No. 10
Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document. � The rack documentation included with your rack solution describes how to install your system into a rack. �The Hardware Owner’s Manual provides information about system features and describes how to troubleshoot the system and install or replace system components. This document is available o
Summary of the content on the page No. 11
Technical Specifications Processor Processor type Up to four AMD Opteron™ 6000 Series processors Expansion Bus Bus type PCI Express Generation 2 Expansion slots Riser 1 Slot 1: x8 link with x16 physical connector, 9.5-inch length, standard height Slot 2: x4 link with x8 physical connector, low-profile with a standard height bracket System Board Slot 3: x8 link with x8 physical connector, low-profile Slot 4: x8 link with x8 physical connector, low-profile Riser 2 Slot 5: x8 link with x16 phy
Summary of the content on the page No. 12
Drives Hard drives Up to six 2.5-inch, internal hot-swappable SAS, SATA, or SSD drives Diskette drive Optional external USB 1.44 MB Optical drive One optional slimline SATA DVD-ROM or DVD+RW drive NOTE: DVD devices are data only. Flash drive Optional internal USB Optional internal dual SD module Optional vFlash card (with iDRAC6 Enterprise card) Connectors Back NIC Four RJ-45 (for integrated 1 GB NICs) NIC One optional management NIC port on iDRAC6 (management NIC) Enterprise card Serial 9-pi
Summary of the content on the page No. 13
Video Video type Integrated Matrox G200 with iDRAC6 Video memory 8 MB (shared with iDRAC application memory) Power AC power supply Wattage 1100 W Voltage 100-240 VAC, 50/60 Hz, auto-ranging Heat dissipation 4012 BTU/Hr Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less Batteries System battery CR 2032 3.0-V lithium coin cell Physical Height 8.64 cm (3.40 in) Width 44.05 cm
Summary of the content on the page No. 14
Environmental NOTE: For additional information about environmental measurements for specific system configurations, see www.dell.com/environmental_datasheets. Temperature Operating 10° to 35°C (50° to 95°F) with a maximum temperature gradation of 10°C per hour NOTE: For altitudes above 2950 feet, the maximum operating temperature is derated 1ºF/550 ft. Storage –40° to 65°C (–40° to 149°F) with a maximum temperature gradation of 20°C per hour Relative humidity Operating 20% to 80% (noncondens
Summary of the content on the page No. 15
Systèmes Dell™ PowerEdge™ R815 Guide de mise en route Modèle réglementaire série E05S
Summary of the content on the page No. 16
Remarques, précautions et avertissements REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : une PRÉCAUTION vous avertit d'un risque de dommage matériel ou de perte de données en cas de non-respect des instructions données. AVERTISSEMENT : un AVERTISSEMENT vous avertit d'un risque d'endom- magement du matériel, de blessure corporelle ou de mort. ____________________ Les informations contenues dans ce document so
Summary of the content on the page No. 17
Installation et configuration AVERTISSEMENT : avant de suivre la procédure suivante, lisez les consignes de sécurité fournies avec le système. Déballage du système Sortez le système de son emballage et identifiez chaque élément. Assemblez les rails et installez le système dans le rack en suivant les consignes de sécurité et les instructions d'installation du rack fournies avec votre système. Guide de mise en route 15
Summary of the content on the page No. 18
Facultatif – Connexion du clavier, de la souris et du moniteur Connectez le clavier, la souris et le moniteur (si nécessaire). Aidez-vous des icônes des connecteurs situés à l'arrière du système pour savoir où insérer chaque câble. N'oubliez pas de serrer les vis situées sur le connecteur du câble du moniteur, s'il en est équipé. Branchement du ou des câbles d'alimentation Connectez le ou les câbles d'alimentation au système et, si vous utilisez un moniteur, connectez son câble d'alimentation
Summary of the content on the page No. 19
Fixation du ou des câbles d'alimentation Faites une boucle comme indiqué dans l'illustration, puis fixez-le à l'aide de la sangle fournie. Branchez ensuite l'autre extrémité du câble d'alimentation sur une prise secteur mise à la terre ou sur une source d'alimentation autonome (onduleur ou unité de distribution de l'alimentation). Mise sous tension du système Appuyez sur le bouton d'alimentation du système et sur celui du moniteur. Les voyants d'alimentation doivent s'allumer. Guide de mise
Summary of the content on the page No. 20
Installation du cadre en option Installez le cadre (si nécessaire). Finalisation de l'installation du système d'exploitation Si vous avez acheté un système d'exploitation préinstallé, consultez tout d'abord la documentation associée, fournie avec le système. Pour une première instal- lation du système d'exploitation, consultez la documentation relative à l'instal- lation et à la configuration du système d'exploitation. Veillez à installer le système d'exploitation avant tout élément matériel
