Summary of the content on the page No. 1
Installation/Operation
Frontload Washers
Metered Commercial
FLW1526C
Para bajar una copia de estas instrucciones
en español, visite www.comlaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 802734R5
www.comlaundry.com September 2010
Summary of the content on the page No. 2
Summary of the content on the page No. 3
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are factors which cannot be built into these washers. These factors MUST BE supplied
Summary of the content on the page No. 4
Safety Information.............................................................................. 4 Table of Explanation of Safety Messages........................................................... 4 Important Safety Instructions ............................................................... 4 Contents Installation........................................................................................... 6 Dimensions and Specifications...........................................................
Summary of the content on the page No. 5
Step 7: Start Washer......................................................................... 27 Indicator Lights................................................................................ 27 Maintenance ........................................................................................ 28 User-Maintenance Instructions............................................................. 28 Cold Weather Care........................................................................... 28 Care of Y
Summary of the content on the page No. 6
Safety Information Explanation of Safety Messages Important Safety Instructions Throughout this manual and on machine decals, you (Save These Instructions) will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific WARNING instructions. These precautions are intended for the personal safety of the operator, user, servicer, and To reduce the risk of fire, electric shock, those maintaining the machine. serious injury or death to persons when using your wash
Summary of the content on the page No. 7
Safety Information 11. Do not repair or replace any part of the washer, or 20. Be sure water connections have a shut-off valve attempt any servicing unless specifically and that fill hose connections are tight. CLOSE recommended in the user-maintenance the shut-off valves at the end of each wash day. instructions or in published user-repair 21. Loading door MUST BE CLOSED any time the instructions that you understand and have the washer is to fill, tumble or spin. DO NOT bypass skills to c
Summary of the content on the page No. 8
Installation Dimensions and Specifications Coin Slide Models 21.56 in. (54.76 cm) Electronic Control Models 22.06 in. (56.03 cm) 24 in. (61.0 cm) 13.1 in. (33.3 cm) 28 in. (71.1 cm) 26.875 in. (68.3 cm) 2 in. FLW2201N (5.1 cm) 1.5 in. (3.8 cm) MODELS EQUIPPED WITH DRAIN HOSE FLW2201N Coin Slide Models 21.56 in. (54.76 cm) Electronic Control Models 22.06 in. (56.03 cm) 24 in. (61.0 cm) 13.1 in. (33.3 cm) 28 in. (71.1 cm) 4.1 in. 4.2 in. (10.41cm) (10.67cm) 1.5 in. 1 26.875 in.
Summary of the content on the page No. 9
Installation NOTE: If the washer is delivered on a cold day Before You Start (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to Tools operate it until the washer has had a chance to For most installations, the basic tools you will need warm up. are: NOTE: Install dryer before washer. This allows room for attaching exhaust duct. 1 3 2 NOTE: Some moisture in the wash drum is normal. 4 Water is used during testing at the manufacturer. 5 D074I
Summary of the content on the page No. 10
Installation Step 2: Position and Level the Washer Installing the Washer Step 1: Position Washer Near Installation WARNING Area Washers elevated above floor level must Move washer so that it is within 4 feet (1.2 meters) of be anchored to that elevated surface, the desired area of installation. base or platform. The material used to elevate the washer should also be NOTE: For best performance and to minimize anchored to the floor to ensure that the vibration or movement, install washer o
Summary of the content on the page No. 11
Installation NOTE: DO NOT slide washer across floor if the Step 3: Connect Fill Hoses leveling legs have been extended, as legs and base could become damaged. WARNING Remove rubber feet from accessories bag and place on Under certain conditions, hydrogen gas all four leveling legs. may be produced in a hot water system Verify that unit doesn’t rock. that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used 3 for such a period and
Summary of the content on the page No. 12
Installation Turn on the water supply faucets and flush the lines for IMPORTANT: Hoses and other natural rubber approximately two minutes to remove any foreign parts deteriorate after extended use. Hoses may materials that could clog the screens in the water develop cracks, blisters or material wear from the mixing valve. temperature and constant high pressure they are subjected to. NOTE: When installing in newly constructed or renovated building, it is very important to flush the All hoses
Summary of the content on the page No. 13
Installation Risers Step 4: (Non-Gravity Drain Models Only) Connect Drain Hose to Drain Receptacle Risers (or air cushions) may have to be installed if the pipes knock or pound when flow of water stops. The Remove the drain hose from its shipping position on risers are more efficient when installed as close as the rear of the washer by removing the shipping tape. possible to the water supply faucets (refer to IMPORTANT: Drain receptacle must be capable of Figure 6). handling a minimum of
Summary of the content on the page No. 14
Installation Standpipe Installation Step 5: (Gravity Drain Models Only) Connect Drain Outlet to Drain System Place the drain hose into the standpipe. Remove drain fitting (four inches long) and hose Remove the beaded tie-down strap from accessories clamp from accessories bag. Insert drain fitting into bag and place around standpipe and drain hose and drain outlet hose. Clamp hose and fitting. tighten strap to hold hose to standpipe. Refer to Figure 8. This will prevent the drain hose from
Summary of the content on the page No. 15
Installation Step 6: Remove the Shock Sleeves and Shipping Brace Remove front access panel by removing the two screws 1 at the bottom of the panel. Remove the five bolts and lockwashers from shipping brace with 9/16 in. wrench and remove brace. Refer to Figure 10. One is holding the brace to the weight. Remove this bolt first. Four bolts are located on the 2 washer base. Remove the two front bolts next and then the two rear bolts. Remove all four shock sleeves by 3 pulling on the yellow
Summary of the content on the page No. 16
Installation Step 8: Plug In the Washer Electrical Requirements 2 (120 Volt, 60 Hertz with 3-Prong Grounding Plug) 3 1 NOTE: The wiring diagram is located in the control hood. 120±12 0 V.A.C. V.A.C. WARNING 120±12 To reduce the risk of fire, electric shock, V.A.C. 5 4 serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical Code, Standard 120 Volt, 60 Hertz ANSI/NFPA No. 70, and such local 3-Wire Effectively regulations as might a
Summary of the content on the page No. 17
Installation Grounding Instructions Step 9: Check Installation The washer must be grounded. In the event of Refer to Installer Checklist on the back cover of this malfunction or breakdown, grounding will reduce the manual and make sure that washer is installed risk of electric shock by providing a path of least correctly. resistance for electric current. Run washer through one complete cycle to make sure The washer is equipped with a cord having an it is operating properly. equipment-groundi
Summary of the content on the page No. 18
Installation 2. If installing a Greenwald coin slide, position Vending extension lever (to be installed on extension bracket) with arm that has one star facing down. Meter Case Refer to Figure 13. The factory mounted coin meter case does not include the service door lock, coin slide, coin drawer, coin Greenwald Monarch or drawer lock or keys. These parts must be ordered (at Coin Slide ESD Coin Slide extra cost) according to the purchaser’s requirements direct from the manufacturer of you
Summary of the content on the page No. 19
Installation 6. Check to make sure coin slide is operating Installing Extension Onto Coin Slide: properly by inserting coins and starting a cycle. Option 1 The IN USE light will turn on, or flash if it is 1. Install slide extension onto top of coin slide using already on, to indicate proper operation. two remaining screws and lockwashers. Refer to Installing Extension Onto Coin Slide: Figure 15. Option 2 1. Install coin slide according to manufacturer’s Attaching Screws instructions. Lo
Summary of the content on the page No. 20
Operation Step 2: Close Loading Door Operation Instructions for Coin Slide Operated Washers Close the loading door tightly. The washer will not operate with the loading door open. IMPORTANT: Prior to first wash, use an all- O purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washtub. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Step 1: Load Laundry Load items loos
