Infinity Wakeboard Tower Sound System 2100m user manual

Summary of the content on the page No. 1

®
MARINE
6100m,
6000m,
¨
off auto on
2100m
wakeboard tower
sound system
instructions
Thank you
Infinity would like to take this opportunity to thank you for
purchasing one of our products. In order that we may better
serve you should you require warranty service, please retain
your original purchase receipt. If you would like to register your
product, please visit our Web site at www.infinitysystems.com.

Summary of the content on the page No. 2

INTRODUCTION INSTALLATION WARNINGS DESCRIPTION CLEANING AND PRECAUTIONS WARNING! • Always wear protective eyewear when using • The 6000m Wakeboard Tower Speakers are Although the 6000m speaker pods are water- Loud music can cause permanent damage to your tools. constructed of weatherproof cast-polymer, and salt-spray-resistant, keep in mind that the hearing. We recommend listening to your system and have passed our most stringent tests to speakers are exposed and may be damaged at moderate vo

Summary of the content on the page No. 3

MOUNTING THE 6000M SPEAKERS CONNECTING THE SPEAKERS The 6000m speakers use a unique mounting SURFACE-MOUNTING SWIVELING THE SPEAKERS Connect the speakers to an amplifier using bracket that works with various tube sizes Some towers may have a flat support panel used Located at the base of the speaker mounting the supplied speaker wires. The weatherproof and flat mounting surfaces. The speakers also to mount accessories such as lighting, board bracket is a swivel-lock pin. Pull this pin up conne

Summary of the content on the page No. 4

MOUNTING THE AMPLIFIER CONTROLS AND SETTINGS Mount the 6100m or 2100m amplifier in a NOTE: When using the Hi-level inputs, connect Setting the controls on the 6100m amplifier or PAGE EXT SWITCH location that is away from direct contact with the REMOTE terminal to the source unit. 2100m amplifier. When set to the ON position, the Page Ext water, whether from washing, big waves or switch will allow the PA signal to pass through soggy riders. REMOTE OUT SETTING THE GAIN to another amplifier when u

Summary of the content on the page No. 5

6100M MICROPHONE MICROPHONE OPERATION MOUNTING THE MICROPHONE CONNECTOR PLATE MOUNTING THE MICROPHONE HOLDER POWER SWITCH Figure 11. Microphone. Locate a suitable place for the microphone plate Locate a position to secure the microphone OFF – Turns the 6100 system off. to be installed. (Make sure that there are no holder and mark screw hole positions. wires or control lines behind this surface.) AUTO – Allows the 6100m system to operate in NOTE: This location should be within reach of the conju

Summary of the content on the page No. 6

APPLICATIONS Figure 12. 6100m System speaker-level connection. Figure 13. 6100m System line-level connection. Remote Remote Turn-On Turn-On LF Speaker RF Speaker Splices Splices Source Unit (not supplied) (not supplied) Source Unit L Speaker R Speaker LR Speaker RR Speaker 6

Summary of the content on the page No. 7

APPLICATIONS Figure 14. 6100m System with a 2100m amplifier Figure 15. 6100m System with a 2100m amplifier and 6000m speakers. powering internal boat speakers. PAGE EXT PAGE ON OFF EXT 6100m 2100m ON OFF OR 6100m 2100m Remote Turn-On Remote LF Speaker RF Speaker Out Remote Turn-On Source Unit Source Unit LR Speaker RR Speaker NOTE: If the 6100m is turned off using the Power switch, there is NOTE: Match the gain of the output of the two speaker sets so they perform at the same volume level

Summary of the content on the page No. 8

TROUBLESHOOTING SPECIFICATIONS • PROBLEM: • PROBLEM: • PROBLEM: 6100m No audio (POWER LEDs are off). No audio (blue LED off, red LED flashing). ** No audio from page. • 125W x 2 ch. • Frequency Response: 10Hz – 40kHz CAUSES and SOLUTIONS: CAUSE and SOLUTION: CAUSES and SOLUTIONS: • Signal-to-Noise Ratio: 91dB 1. No voltage at Batt + or remote terminal. 1. Thermal protection. 1. Microphone is not connected properly. • Line-Level Input Sensitivity: 250mV – 6V – Check all power connections with a