Harbor Freight Tools 95593 - 1.5 HP user manual

User manual for the device Harbor Freight Tools 95593 - 1.5 HP

Device: Harbor Freight Tools 95593 - 1.5 HP
Category: Camera Lens
Manufacturer: Harbor Freight Tools
Size: 1.06 MB
Added : 11/30/2014
Number of pages: 14
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Harbor Freight Tools 95593 - 1.5 HP. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Harbor Freight Tools 95593 - 1.5 HP.

For your convenience

If looking through the Harbor Freight Tools 95593 - 1.5 HP user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Harbor Freight Tools 95593 - 1.5 HP on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Harbor Freight Tools 95593 - 1.5 HP to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Harbor Freight Tools 95593 - 1.5 HP User manual - Online PDF
Advertisement
« Page 1 of 14 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Harbor Freight Tools 95593 - 1.5 HP but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Harbor Freight Tools 95593 - 1.5 HP. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

VERTICAL FLOAT SUMP PUMP
Model 95591 - .75 HP
Model 95592 - 1 HP
Model 95593 - 1.5 HP
SET UP And OPERATIng InSTRUCTIOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can

Summary of the content on the page No. 2

4000 3500 3000 2500 2000 1500 1000 500 SPECIFICATIOnS Model 95591 Model 95592 Model 95593 Motor 115 V~ / 60 Hz / 4 A 115 V~ / 60 Hz / 5.5 A 115 V~ / 60 Hz / 6 A / 3/4 HP / 1 HP / 1.5 HP Power Switch Type Automatic Float Switch Power Plug Type 3-Prong / Grounded Self Priming Yes Maximum Pumping Capacity 3,000 GPH 3,300 GPH 3,700 GPH Maximum delivery Height 20’ 24’ 26’ discharge diameter 1-1/4 NPT Female / 1-1/2 NPT Male Max. Operating Temperature 95° Fahrenheit Performance Chart 30 KEY 25 Model

Summary of the content on the page No. 3

a polarized outlet. do not change WORK AREA the plug in any way. Double insula- 1. Keep your work area clean and tion eliminates the need for the well lit. Cluttered benches and dark three wire grounded power cord and areas invite accidents. grounded power supply system. 2. do not operate power tools in 3. Avoid body contact with grounded explosive atmospheres, such as in surfaces such as pipes, radiators, the presence of flammable liquids, ranges, and refrigerators. There is gas

Summary of the content on the page No. 4

information. If unreadable or miss- TOOL USE And CARE ing, contact Harbor Freight Tools for a 1. disconnect the Power Cord Plug replacement. from the power source before making any adjustments, changing 2. Wear AnSI-approved accessories, or storing the Sump safety impact eye gog- Pump. Such preventive safety mea- gles when assembling sures reduce the risk of starting the the Pump. Using per- unit accidentally. sonal safety devices reduce the risk for injury. Safety impact eye goggl

Summary of the content on the page No. 5

6. do not pump hazardous materials. Any outlet should be above the Do not pump explosive or flammable water line. materials such as fuel, oil, kerosene, 11. nEVER raise or lower the Pump by gasoline, etc. Do not pump in close its electrical Power Cord. proximity to flammable or explosive materials. Do not pump fats, oils, 12. In cold weather, when the Pump salt or waste water. This Pump is is not in use, protect the interior designed to move clean or dirty of the Pump from freezing

Summary of the content on the page No. 6

of electric shock. (See 3-Prong Plug gROUndIng and Outlet.) TO PREVEnT WARnIng 2. The grounding prong in the plug is ELECTRIC SHOCK connected through the green wire in- And dEATH FROM side the cord to the grounding system InCORRECT gROUndIng in the tool. The green wire in the cord WIRE COnnECTIOn: must be the only wire connected to Check with a qualified the tool’s grounding system and must electrician if you are in doubt never be attached to an electrically as to whether the ou

Summary of the content on the page No. 7

2. Double insulated tools may be used dition. Always replace a damaged in either of the 120 volt outlets shown extension cord or have it repaired by in the preceding illustration. (See a qualified electrician before using it. Outlets for 2-Prong Plug.) 8. Protect the extension cords from sharp objects, excessive heat, and Extension Cords damp or wet areas. 1. Grounded tools require a three wire RECOMMEndEd MInIMUM WIRE extension cord. Double Insulated gAUgE FOR EXTEnSIOn CORdS* tools

Summary of the content on the page No. 8

UnPACKIng When unpacking, check to make sure all the parts shown on the Parts List on page 12 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY And OPERATIng InSTRUCTIOnS note: For additional information regarding the parts listed in the following pages, refer to the Assembly diagram on page 13. WARnIng! Always make sure to turn off the electricity powering the Pump’s electrica

Summary of the content on the page No. 9

CHECK VALVE FIgURE E OR UnIOn (nOT InCLUdEd) TO 115 VOLT, gROUndEd gFCI OUTLET dISCHARgE PIPE (nOT InCLUdEd) 1/8” AIR BLEEd HOLE o BASE (25) 3. Connect the Discharge Pipe to the Base (25). nOTE: Make sure the Discharge Pipe is secured to a solid surface, with appropriate hardware (not included), to ensure the stability of the Pump. (See Figure E.) 4. Install an additional union (not included) or other means of separating the Dis- charge Pipe just above the floor to facilitate removal of the

Summary of the content on the page No. 10

6. Carefully set the Pump in place. do not lower or raise the Pump by the Power Cord or discharge Pipe. (See Figure E.) 7. The Float Switch (2) automatically switches on and off at a water depth of approxi- mately 4 inches. The ON/OFF height can be manually changed by adjusting the Float Switch Lock. CAUTIOn: Do not run the Pump dry. Doing so will increase wear to the unit and possibly cause seal damage. (See Figure E.) note: This Pump has a built-in thermal protector for the Motor wh

Summary of the content on the page No. 11

2. To clean the Impeller Cover and Impeller: A clogged or dirty Impeller Cover or Impeller (28) will greatly reduce performance of the Pump. To clean the Impel- ler Cover (31), spray the Cover with clean water. To clean the Impeller, remove the nine Screws (32) at the bottom of the Base (25). Then, remove the Base to expose the Impeller Cover and Impeller. Use a stream of clean water to clean the Impeller and Impeller area inside the Pump. Then, replace the Base. (See Assy. diagram.)

Summary of the content on the page No. 12

PLEASE REAd THE FOLLOWIng CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,

Summary of the content on the page No. 13

ASSEMBLY dIAgRAM SKU 95591/95592/95593 For technical questions, please call 1-800-444-3353 PAGE 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Power Cord/Plug not shown. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. *Internal Motor Parts Are Not Consumer-Serviceable.

Summary of the content on the page No. 14

LIMITEd 1 YEAR / 90 dAY WARRAnTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Har- bor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all


Alternative user manuals
# User manual Category Download
1 Harbor Freight Tools 95591 - .75 HP User manual Camera Lens 0
2 Harbor Freight Tools 95592 - 1 HP User manual Camera Lens 0
3 iSimple BLUSTREAM ISBT21 User manual Camera Lens 3
4 Sony E 16mm F28 User manual Camera Lens 3
5 Sony Cyber-shot DSC-S750 User manual Camera Lens 21
6 Sony Cyber-shot DSC-P71 User manual Camera Lens 28
7 Sony DT 16-50mm f/2.8 Standard Zoom Lens SAL1650 User manual Camera Lens 44
8 Sony E 55-210mm F4.5-6.3 OSS User manual Camera Lens 32
9 Sony Cyber-shot DSC-W200 User manual Camera Lens 15
10 Sony User manual Camera Lens 14
11 Sony DSCT70 User manual Camera Lens 3
12 Sony NEX-3 User manual Camera Lens 39
13 Sony DT 55-300mm F4.5-5.6 SAM User manual Camera Lens 5
14 Sony SAL-135F28 User manual Camera Lens 1
15 Sony NEX-3C User manual Camera Lens 4