Summary of the content on the page No. 1
User’s Manual
CIA111, CIA114, and CIA114F5
Wall Box and Floor Box Mountable Interfaces
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd. #04-01 Kyodo Building, 16 Ichibancho 68-809-01 Rev. C
Anaheim, CA 92805 3821 AH Amersfoort, The Netherlands PM Industrial Bldg., Singapore 368363 Chiyoda-ku, Tokyo 102-0082
02 08
800.633.9876 714.491.1500 +800.3987.6673 +31.33.453.4040 +800.7339.
Summary of the content on the page No. 2
Precautions Safety Instructions � English Extron’s Warranty Warning Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety Extron Electronics warrants this product against defects in materials and wor
Summary of the content on the page No. 3
警告 安全须知 • 中文 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 这个符号提示用户该设备用户手册中 必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线 有重要的操作和维护说明。 （ 地 线 ） 是 安 全 设 施 ， 不 能 不 用 或 跳 过 。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部没 注意 有用户可以更换的零件。为避免出现触电危险不要自己 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 试图打开设备盖子维修该设备。 解 所 有 安 全 和 使 用 说 明 。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危
Summary of the content on the page No. 4
Chapter One • Introduction..................................................... 1-1 About this Manual ..................................................................... 1-2 Chapter One • Introduction..................................................... 1-1 About the CIA111, CIA114, and CIA114F5. ......................... 1-2 Features. ........................................................................................ 1-2 Chapter Two • Installation and Operation.................... 2-1
Summary of the content on the page No. 5
Table of Contents, cont'd CIA111 and CIA114 Computer Video Interface Chapter One 1 Introduction About.this.Manual About.the.CIA111,.CIA114,.and.CIA114F5 Features 68-809-01.Rev. C 02.08 All trademarks mentioned in this manual are the properties of their respective owners. ii CIA111 and CIA114 • Table of Contents
Summary of the content on the page No. 6
Introduction About this Manual CIA111 and CIA114 Computer Video Interface This manual contains information about installing and operating the Extron CIA111, CIA114, and CIA114F5 interfaces. About the CIA111, CIA114, and CIA114F5 The Extron CIA111, CIA114, and CIA114F5 are wall box or floor box mountable computer video interfaces. The CIA111 mounts to a wall or podium using a two-gang junction box and has mounting spaces for up to four single-space Mini Architectural Adapter Plates (MAAPs).
Summary of the content on the page No. 7
Installation Installation Overview Front Panel Features and Cabling Installation and service must be performed by C 2 1 2 1 authorized personnel only. UL Listed electrical boxes are recommended. See "UL Requirements", later in this chapter. IMAGE SHIFT NO MONITOR IMAGE SHIFT NO MONITOR To install and set up a CIA111, CIA114, or CIA114F5 interface, follow these steps: MONITOR OUTPUT MONITOR OUTPUT 3 3 1 Turn all of the equipment off. Make sure that the COMPUTER IN
Summary of the content on the page No. 8
AUDIO L R AUDIO L R Installation, cont’d 4 Audio Input connector — Plug a computer audio source e into this 3.5 mm stereo jack. Wire the connector as shown in figure 2-2. Tip (+) Sleeve 3 2 Ring (-) Tip (+) Sleeve ( ) 3.5 mm Audio Plug Figure 2-2 — Tip, ring, and sleeve 5 1 IMAGE SHIFT CONTROL Auto Power LED — This LED lights to indicate that a VGA OUTPUT SYNC FORMAT (SYNC ON GREEN) f OUTPUT SYNC FORMAT (RGBHV/RGBS) input cable has been connected to the front panel Computer NO MON
Summary of the content on the page No. 9
Installation, cont’d Pre-installation Testing and Troubleshooting Mode Select DIP switches — Set these switches to select e Before installing the interface into the wall or furniture, test the settings for horizontal position control, sync format, monitor system to verify that the connections and settings are correct. emulation, and Auto Power. Apply power to the interface. If an active sync signal is present 1 — Image Shift control on the input or if the auto-power feature is disabled
Summary of the content on the page No. 10
Installation, cont’d The CIA111 and CIA114 interfaces must be When the image is displayed correctly C installed into Underwriters Laboratories (UL) Once the system has been cabled and tested, the interface can approved electrical wall boxes. See the following be installed in the wall or furniture. To mount the interface section on UL requirements. The wall boxes are and install optional MAAP devices (CIA111 only), see the next not included with the inter
Summary of the content on the page No. 11
Installation, cont’d 6. Insert the wall box into the opening, and attach it to the wall stud or furniture with nails or screws, leaving the front edge flush with the outer wall or furniture surface (figure 2-6). Wall Stud 2-gang Wall Box Screws or Nails Extron CIA111 Cable Clamp Extron MAAP Installation Cable Figure 2-7 — Mounting the optional MAAP device Figure 2-6 — Attaching the wall box to a wall stud (standard MAAP device shown) If attaching the wall box to wood, use four #8 or #1
Summary of the content on the page No. 12
Installation, cont’d Mounting the interface to the wall box Mounting the CIA114F5 1. Remove power from the interface by disconnecting the The CIA114F5 is designed to fit into a Steel City 665 floor box power supply. (figure 2-9). The installation must conform to national and local electrical codes and to the interface’s size requirements. 2. Place the interface through the opening in the wall or furniture and into the wall box. Take care not to damage Theinterface must be installedi
Summary of the content on the page No. 13
Installation, cont’d Preparing the site and cables CIA111 and CIA114 Computer Video Interface 1. Choose a location that allows cable runs without interference. Allow enough depth for both the floor box and the cables. You need to run the conduit (if required by local code) and cables under the floor before installing the interface. 2. Install the floor box in accordance with the documentation that accompanied the box. 3. Feed cables through the floor box punch-out holes, and secure them
Summary of the content on the page No. 14
Reference Information Audio Specifications Gain ................................................. Unbalanced output: 0 dB; balanced output: +6 dB Video Frequency response ...................... 20 Hz to 20 kHz, ±0.4 dB Gain ................................................. Unity Bandwidth ...................................... 250 MHz (-3 dB) THD + Noise .................................. 0.03% @ 1 kHz at nominal level, 0.1% @ 20 kHz at maximum output S/N ....................................
Summary of the content on the page No. 15
Reference Information, cont’d Rack mount Part Numbers CIA111, CIA114 .................. No, but wall or furniture mountable ® CIA interface part numbers CIA111AM .......................... No, but Ackerman GB3 floor box mountable Included parts Part numbers ® CIA114F5 ............................ No, but Steel City 665 floor box CIA111 with cable guard (black, white) 60-596-12, -13 mountable ® CIA111 without cable guard (black, white) 60-596-22, -23 CIA114AM .......................... No, but
Summary of the content on the page No. 16
3.0" (7.6 cm) Reference Information, cont’d Accessories These items can be ordered separately: Accessories Part numbers Modular A/V panel for Steel City 665 floor box (for CIA114F5 only) 60-585-11 5.0" (12.7 cm) Assorted MAAPs (CIA111 only) Cables and Adapters Cables and adapters Part numbers 4.1" VGAM 6' MHRA cable with audio 26-490-02 (10.5 cm) Mac adapter VGAM kit with audio 70-156-01 Top Panel 4.5" (11.4 cm) 13W3 adapter VGAM kit with audio 70-157-03 Templates SURFACE CUT-OUT AREA FOR FURN
Summary of the content on the page No. 17
3.0" (7.6 cm) Reference Information, cont’d 2.75" (7.0 cm) 2.1" (5.3 cm) Top Panel 4.5" (11.4 cm) Location of CIA114 SURFACE CUT-OUT AREA FOR FURNITURE MOUNT To install CIA114 directly into furniture, cut along this line. TEMPLATE IS NOT FULL SIZE. Cut-Out Template for Extron's CIA114 A-8 CIA111 and CIA114 • Reference Information
