Summary of the content on the page No. 1
Quick Installation Guide
Version 1.0
P0715
7" Compact Intel Low Voltage
PIII / Celeron Panel PC
Summary of the content on the page No. 2
© Copyright 2006 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer. Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequen-tial damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages. This docu
Summary of the content on the page No. 3
Warning Panel PC and their components contain very delicate Integrated Circuits (IC). To protect the Panel PC and its components against damage from static electricity, you should always follow the following precautions when handling it : 1. Disconnect your Panel PC from the power source when you want to work on the inside 2. Hold the board by the edges and try not to touch the IC chips, leads or circuitry 3. Use a grounded wrist strap when handling computer components. 4. Place components on a
Summary of the content on the page No. 4
Getting Started This section will help you have your P0715 up and running smoothly. PACKING LIST P0715 9 x Screws 1 x Arm Holder Bracket 2 x Wall Mount Bracket 1 x Adaptor 2 x Power Cord (American & French Cordset) 1 x Driver CD Before up and running, please make sure the package contains all of above accessories. If any of the above items is damaged or missing, contact your vendor immediately. 4 P0715 Quick Installation
Summary of the content on the page No. 5
Specification Model Name Panel PC P0715 Intel Low Voltage Celeron 400~733MHz CPU CPU FSB100/133MHz Cache 2nd Level 256K Memory 1 x 144Pin SO-DIMM up to 512MB SDRAM VRAM SMI722 G8 Lynx 3D+ engine 8MB Video RAM on chip System Chipset Intel 815E + Intel CH2 ATA / IDE Ultra DMA 33, support 2 IDE device Audio Realtek ALC202A AC97 Codec, support Line-out Watchdog Timer 127-level Reset System Fan 1 x 4cm x 4cm / 8 CFM Serial Port 2 x RS-232 ports (COM1/2) USB Port 2 x USB 1.1 compliant KB / MS 1 x PS2
Summary of the content on the page No. 6
Mounting Arm Mounting Hook Mounting 6 P0715 Quick Installation
Summary of the content on the page No. 7
Dimension Unit: mm P0715 Quick Installation 7 7
Summary of the content on the page No. 8
OSD of Front Panel 8 P0715 Quick Installation
Summary of the content on the page No. 9
Location of I/O Ports Before starting to install software on your new Panel PC please spend some time to find out the exact location of connectors and HDD (if pre-installed). The front panel does not contain any indicators, switches, connectors or drive access. All these are to be found on the left and right side and on the rear of the system. Default I/O P0715 Quick Installation 9 9
Summary of the content on the page No. 10
Connecting Peripherals The user can use the I/O interfaces located at the backside of the chassis to connect external peripheral devices, such as a mouse, a keyboard, a monitor, serial devices or parallel printer etc. Before connection, make sure that the computer and the peripheral devices are turned off. Connecting an external CRT P0715 has a 15-pin analog RGB interface connec- tor located at the rear side of the chassis. As to resolution, P0715 otputs 800 x 480 instead of 800 x 600, it won't
Summary of the content on the page No. 11
LAN Port P0715 provides one Intel 82562ET 100/10 Base-T Ethernet (RJ-45) interface. For network connection, follow the instructions below; 1. Turn off the Panel PC system and the Ethernet hubs. 2. Plug in one end of cable of a 100/10 Base-T hub to the system's RJ-45 jack. USB Ports P0715 provides four external USB ports to connect to external USB devices. USB ports and devices are hotplug capable. Therefore any USB device can be connected at all time without the need to power down your system. N
Summary of the content on the page No. 12
Hardware Installation HDD installation 1. On the back of P0715, locate the screws that secure the rear case. Use screw driver to remove the screws. Keep the screws safely for later use. Pull the baffle slightly upward the main unit until it is disen- gaged from main unit. 2. Put the HDD into the drive bay and screw it on. 12 P0715 Quick Installation
Summary of the content on the page No. 13
44 pin IDE Cable 2.5" HDD Pin 1 Pin 1 Note: Beware of the directions when wiring HDD and IDE cable. P0715 Quick Installation 13 13
Summary of the content on the page No. 14
Panel PC Installation 1. In 2.4B or above Driver, choose Drivers & Utili- ties. 14 P0715 Quick Installation
Summary of the content on the page No. 15
1.1 Select Panel Computing. P0715 Quick Installation 15 15
Summary of the content on the page No. 16
1.2 Select P0715. 16 P0715 Quick Installation
Summary of the content on the page No. 17
1.3 Install All Drivers. P0715 Quick Installation 17 17
Summary of the content on the page No. 18
2. Install Touch Screen Driver. 18 P0715 Quick Installation
Summary of the content on the page No. 19
4. Select Promote Touch Driver to install. P0715 Quick Installation 19 19
