Summary of the content on the page No. 1
Cordless Phone
Operating Instructions
Model No. KX-TC2100AL
KX-TC2100NZ
PLEASE READ
BEFORE USE AND
SAVE.
Charge the battery for
about 9 hours before
initial use.
Contents by
1 Getting Started
2 Making/Answering Calls
3 Speed Dialler
4 One-Touch Dialler
5 Special Features
6 Things You Should Know
Copyright:
This material is copyrighted by Panasonic Communications (Malaysia)
Sdn. Bhd., and may be reproduced for internal use only. All other
reproduction, in whole or in part, is prohibited wi
Summary of the content on the page No. 2
Telephone Line Cord 1 Getting Started 1-A Accessories 1-B Location of Controls A AC Adaptor . one A Battery . . . . . one Handset Base unit Antenna Antenna (1-C) A Telephone Line Cord . . . . . . . . . . . . one {TALK} Button (2-A) A For Australia For New Zealand IN USE/CHARGE Indicator (1-C, 5-A) {AUTO} Button {DIRECT} Button (1-C, 3-A, 5-C) (4-A) A Handset Cover . . A Wall/Desk Stand . . {REDIAL} Button {RECALL} Button one one (2-A) (5-C) TALK/RECHARGE Indicator (6-A) {RINGER} {PROGRAM} Bu
Summary of the content on the page No. 3
To select the dialling mode TONE The TALK indicator light must be off before programming. Press {PROGRAM}N{AUTO}N{*} twice (TONE) N N{PROGRAM}. • A beep sounds. • To cancel during programming, press {PROGRAM}. • If 3 beeps sound during programming, a wrong key was pressed. Start again from the beginning. 2 Making/Answering Call 2-A Making Calls 1 Press {TALK}. To redial the last number dialled • The TALK indicator lights. Press {TALK}N{REDIAL}. • If an alarm tone sounds, see section 6-E. 2 Dial
Summary of the content on the page No. 4
3 Speed Dialler 3-A Storing Phone Numbers in Memory You can store up to 10 phone numbers. The dialling buttons ({0} to {9}) function as memory stations. The TALK indicator light must be off before programming. 1 Press {PROGRAM}. If you misdial • The TALK indicator flashes. Press {PROGRAM} to end storing. N N Start again from step 1. 2 Enter a phone number up to 16 digits. 3 Press {AUTO}. To erase a stored number Press {PROGRAM}N{AUTO}N 4 Press a memory station number ({0} to {9}). N the memory s
Summary of the content on the page No. 5
6 Things You Should KnowNN N 6-A Battery 6-B Wall Mounting 6-C Base Unit Location Recharge This unit can be mounted on a wall. Calls are transmitted between the base unit and the handset using wireless radio waves. For maximum distance and noise- When the RECHARGE indicator flashes or the unit beeps 1 Press the tabs in the direction of the arrows (1), then remove free operation, we recommend the following: intermittently, place the handset on the base unit for about the wall/desk stand (2). 9
Summary of the content on the page No. 6
T Things you should Know NN 6-E Troubleshooting 6-F Safety Instructions Take special care to follow the safety suggestions listed below. For Australia Users Only Problem Cause and Remedy No "000" or other calls can be made from this device during Safety a mains power failure. The unit does not work. • Check the settings (1-C). 1) The unit should be connected to a power supply only of the type • Charge the battery fully (6-A). described in the operating instructions or as marked on the unit. Fo
Summary of the content on the page No. 7
5 Special Features 5-A Handset Locator You can locate the handset or page the handset user with beep tones. 1 Press {HANDSET LOCATOR} on the base unit. • The IN USE/CHARGE indicator flashes and the handset beeps for 1 minute. 2 To stop paging, press {HANDSET LOCATOR} again or press {TALK} twice on the handset. 5-B Using the PAUSE Button (For PBX Line/Long Distance Calls) We recommend you press {PAUSE} if a pause is required for dialling with a PBX or to make a long distance call. Ex: Line a
