Summary of the content on the page No. 1
INSTALLATION GUIDE
RCC600-SM Subwoofer Module
RCC600-SA Subwoofer Amplifier
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Thank you for choosing Artison’s RCC 600 In-Wall Subwoofer System. We are pleased that you have selected our high-performance audio products. INTRODUCTION The following information will guide you through the installation and setup of your Artison RCC 600 Subwoofer Module and RCC 600 Subwoofer Amplifier. Your RCC600-SM carton should contain the following: 1 . RCC 600 Subwoofer Module 1 . RCC 600 Subwoofer Module Paint Shield 1 . RCC 600 Subwoofer Module Grille 1 . RCC 600 Subwoof
Summary of the content on the page No. 4
RCC 600 SUBWOOFER MODULE (RCC600-SM) The RCC 600 Subwoofer Module can be installed into either an: 3 Artison Pre Build Box (Volume ≈ 1.2 ft ) SOLD SEPERATELY OR 3 Infinite Baffle (i.e. 2x4 stud wall, 16” On Center spacing at least 8 feet tall, Volume 2.8 ft or greater) IMPORTANT: In an installation of two RCC600-SM’s that are being powered by one RCC600-SA, both Subwoofer Modules need to be in either Pre Build Boxes or be in Infinite Baffles. You cannot connect two RCC 600 Subw
Summary of the content on the page No. 5
properly so that it does not interfere with the driver’s operation. The design of the IW PBB is such that there is NO clearance between the back of the subwoofer module and the back of the PBB. Be careful that no wires are in this area when installing the module INSTALLATION INTO AN INFINITE BAFFLE 1. Use the provided Cut-out Template to mark the desired wall location. Be sure that no piping, wall studs, or electrical wires interfere with the placement of the RCC600-SM. 2. Once th
Summary of the content on the page No. 6
FIGURE 1 FIGURE 2 6
Summary of the content on the page No. 7
RCC 600 SUBWOOFER AMPLIFIER (RCC600-SA) The RCC 600 Subwoofer Amplifier can be installed into either cabinetry, on an equipment shelf, or it can be rack-mounted into a standard 19” Equipment Rack. In any installation be sure to provide adequate ventilation around the amplifier. The RCC600-SA has two simple and conveniently placed mode settings. The Music Mode or Movie Mode user controls are located on the front panel for selection based on the source material. The Mode settings, V
Summary of the content on the page No. 8
RCC600-SA FRONT PANEL CONTROLS GAIN – The position of this knob controls the overall gain (volume) of the subwoofer. Press this button in and it will spring out into a rotating knob, press it back in to hide it. The front panel gain control will become the master gain control until the remote is used. NOTE: The amplifier by default will resume to the last setting by either gain control device. DIM – This button controls the brightness of the Halo lighting on the front panel. There are
Summary of the content on the page No. 9
AUDIO OUTPUTS 1. Connect the speaker wires to the Binding Posts. NOTE: Red is Positive and Black is Negative. 2. Use either Bare Speaker Wire Ends or Banana Plugs to terminate the speaker wire. AUDIO INPUTS 1. Connect to either the Balanced Female XLR or Unbalanced Female RCA Inputs. NOTE: Both inputs have been calibrated to the same sensitivity level. IR FEEDTHRU 1. Connect a ⅛” Stereo MINIJACK to control the RCC600-SA via your integrated control system. 2. Both the IR Feedthr
Summary of the content on the page No. 10
POWER MODES 1. Select either: ON – Always On. AUTO – On with Signal Sense, without signal it will stay on for ≈15 minutes. TRIGGER – On with a 12 Volt trigger. 2. +12V Trigger Input – Use the Green Phoenix Connector to connect a 12 volt trigger wire from your other equipment, the polarity on the connector can be either way. SETUP MODES 1. EQ – Select the appropriate setting based on these guidelines: ∞ Baffle – The RCC 600 Subwoofer Module is installed in a wall that has an air 3
Summary of the content on the page No. 11
to fine tune the signal coincidence of the subwoofer and the lower frequencies of your LCR Speakers. Adjust the phase listening for an increase in mid bass in the crossover region. A pink-noise generator or an RTA (Real-time Analyzer) can further analyze your installation. 3. LOW PASS – This is the crossover frequency setting of the Low Pass Filter. The RCC600-SA comes from the factory with the 80Hz setting that is recommended for use with the Artison LCR speakers. If used in conjuncti
Summary of the content on the page No. 12
1. AUTO EQ MIC – This is the input jack for the ARMC Microphone. 2. Switch Settings – Select either: a. BYPASS – ARMC not active. b. AUTO EQ. – ARMC active. Will remember the last measured room mode sequence and settings. 3. BLUE LED STATUS INDICATOR a. Continuous Short Flash – Switch in AUTO EQ setting, ARMC not yet saved. Since the amplifier leaves the factory with this function having been tested the LED should not flash continuously even when the switch is set to the AUTO E
Summary of the content on the page No. 13
LIMITED WARRANTY ALL INTERNET SALES ARE STRICTLY PROHIBITED This warranty remains in effect for five years from the date of purchase for speaker products and one year for electronic products. THIS WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZED ARTISON DEALER IN THE UNITED STATES. THE ORIGINAL BILL OF SALE MUST BE PRESENTED WHENEVER WARRANTY SERVICE IS REQUIRED. FOR WARRANTY SERVICE OUTSIDE THE UNITED STATES, CONTACT THE AUTHORIZED AR
