Summary of the content on the page No. 1
848D3G93A0 (312)
OWNER/OPERATOR MANUAL
HEDGE-TRIMMERS
HTZ2400
CHTZ2400
Thank you for purchasing a RedMax
WARNING
product.
The engine exhaust from this product Before using our hedge-trimmers,
contains chemicals known to the State please read this manual carefully to
of California to cause cancer, birth
understand the proper use of your unit.
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS : 40100101 and up
Summary of the content on the page No. 2
Summary of the content on the page No. 3
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL WARNING This mark indicates instructions which must be followed in order to prevent accidents which could lead to serious bodily injury or death. IMPORTANT This mark indicat
Summary of the content on the page No. 4
1. Parts location 1. Right handle 2. Fuel tank 3. Starter 4. Left handle 5. Throttle lever 6. Ignition switch 7. Throttle Cable 8. Muffler 9. Blade 10. Front handle 11. Rear handle 4
Summary of the content on the page No. 5
2. Specifications Engine Type······················································································ Air-cooled 2-stroke gasoline Model·········································································································· Zenoah GZ23N 3 Displacement························································································ 1.44cu-in (23.6cm ) -1 Max. output ··································································· 1.09Hp (0.8kW)at 8000/mi
Summary of the content on the page No. 6
3. Warning labels on the machine (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. IMPORTANT If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). WARNING Never modify your machine. We won't warrant the machine, if you use the remodeled hedge-trimmer or you don't observe the proper usage written in the manual.
Summary of the content on the page No. 7
4. Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: AIR CLEANER COVER INFORMATION IMPORTANTE CONCERNANT LE MOTEUR IMPORTANT ENGINE INFORMATION Ce moteur est conformc aux normcs U.S. EPA PH2 et 2
Summary of the content on the page No. 8
5. For safe operation 1.Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4. Never allow children or an
Summary of the content on the page No. 9
5. For safe operation b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product. ■ WORKING PLAN 1. You should never use the product when under the influence of alcohol, when suffering from exhaustion or lack of sle
Summary of the content on the page No. 10
5. For safe operation ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more persons, care should also be taken to constantly look around or otherwise check for the presence and locations of other people working so as
Summary of the content on the page No. 11
5. For safe operation WARNING Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair. ■ USING THE PRODUCT IMPORTANT Cut only materials recommended by
Summary of the content on the page No. 12
5. For safe operation • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. ■ MAINTENANCE 1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual a
Summary of the content on the page No. 13
5. For safe operation ■ HANDLING FUEL 1. The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank. 3. When refilling the tank, always turn off the engine and allow it t
Summary of the content on the page No. 14
6. Fuel ■ RECOMMENDED MIXING RATIO WARNING GASOLINE 50:OIL 1 • Gasoline is very flammable. Avoid 50:1 MIXING CHART smoking or bringing any flame or GASOLINE gal. 1 2345 sparks near fuel. Make sure to stop the 2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13 engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least GASOLINE liter 1 2345 3m (10ft) away from the fueling point 2-CYCLE OIL ml 20 40 60 80 100 before starting the engine. • Exhaust emis
Summary of the content on the page No. 15
6. Fuel again for at least one minute. As some long period of time, clean the fuel tank oils may be difficult to agitate depending after rendering it empty. Next, activate the on oil ingredients, sufficient agitation is engine and empty the carburetor of the necessary for the engine to last long. Be composite fuel. careful that, if the agitation is insufficient, 6. In the case of scrapping the used mixed there is an increased danger of early oil container, scrap it only at an authorized piston s
Summary of the content on the page No. 16
7. Operation ■ STARTING ENGINE OP1 WARNING (1) The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon OP2 (2) starting of the engine. 2. Push the primer pump several times until overflown fuel flows out in the clear tube. (OP1) 3. Move the choke lever to the closed position. (3) (4) (OP2) 4. Set the ignition switch to the “START” position. (OP3) (1) p
Summary of the content on the page No. 17
7. Operation NOTE 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. ■ STOPPING ENGINE (OP3) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the ignition switch to the “STOP” position. IMPORTANT • Except for an emergency, avoid stopp
Summary of the content on the page No. 18
7. Operation WARNING •Weather conditions and altitude may effect carburation. • Do not allow anyone to stay close to the hedge-trimmer while working or while adjusting the carburetor. ■ HOW TO USE HANDLE (CHTZ2400 only) To reduce fatigue when trimming hadges, the handle can be swivelled through 90° to the left or right. (OP7, OP8). Do not press the throttle during this operation! OP7 Proceed as follows: 1. Free the handle by pressing the locking lever; (OP7) 2. Turn the handle until the locking
Summary of the content on the page No. 19
7. Operation HEDGE TRIMMING TECHNIQUES OP9 Trim sides of a hedge first, and then the top. Vertical cut: •With the single-sided blade hedge-trimmer, model HTZ2400 always cut from the bottom up (OP9). With the 2-sided blade model CHTZ2400 use an arcing cut from the bottom upwards, then downwards to use both sides of the blades (OP10). Horizontal cut: OP10 • In order to get the best cutting results, slightly tilt the blade (5÷10°) towards the cutting direction (OP11, OP12). Cut slowly, speciall
Summary of the content on the page No. 20
8. Maintenance ■ MAINTENANCE CHART every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.17) if necessary clean and readjust GAP: .025in(0.6~0.7mm) spark plug ✔ plug gap replace, if necessary cylinder fins, intake air cooling vent clean ✔ muffler, spark arrester
