Summary of the content on the page No. 1
R
TFT-LCD TV/DVD Combo
OWNER'S MANUAL
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
MODELS :
HLC32R1
HLC26R1
Summary of the content on the page No. 2
Warning The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the CAUTION presence of uninsulated dangerous voltage within the RISK ELECTRIC SHOCK product’s enclosure that may be of sufficient magnitude DO NOT OPEN ! ! to constitute a risk of electric shock. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, The exclamation point within an equilateral triangle is DO NOT REMOVE COVER (OR BACK). intended to al
Summary of the content on the page No. 3
Safety Instructions FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is
Summary of the content on the page No. 4
Safety Instructions SAVE THESE INSTRUCTIONS Thank you for purchasing the Haier product. This easy-to-use manual will guide you in getting the best use of your product. Remember to record the model and serial number. They are on label in back of the unit. Model number serial number Date of purchase Staple your receipt to your manual. You will need it to obtain warranty service. 4 TV LCD-TFT
Summary of the content on the page No. 5
Introduction Contents Video Menu Warning . . . . . . . .............. . . . . . . . . . . . . . . . . . . . . . 2 How to select picture mode.................................. Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3 How to customize your own picture status ............. Introduction 21 VGA Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........... 22 6 Aud
Summary of the content on the page No. 6
MENU INPUT VOL+ VOL- CH+ CH- POWER Label Towards Back Introduction Controls This is a simplified representation of the TV front panel, side panel control buttons and side inputs. TV Side panel controls and connections 1.MENU: Menu display. Press to access the on-screen menu display 2.INPUT: Press to access the input source mode. Press repeatedly to change the source to the one you want to watch. In the MENU screen, the INPUT button serves as the ENTER button
Summary of the content on the page No. 7
Introduction Connection Options Back panel connections 2 2 L L D DV VI I A AU UD DI IO O 2 2 1 1 R R 1 1 Y Y P Pb b P Prr L L A AU UD DI IO O R R V VG GA A A AU UD DIIO O V VG GA A 1 1 V VIID DE EO O L L A AU UD DIIO O R R S S--V VIID DE EO O L L A AU UD DI IO O R R L L A AU UD DIIO O R R 1. Digital Audio Output: Connect various types of digital audio equipment. NOTE: In standby mode, these ports will not work. 2. DVI Audio In: When using a DVI to HDMI adapter, connect the audio signal
Summary of the content on the page No. 8
Introduction Remote control The remote control cannot be operated unless the batteries are properly loaded. When using the remote control, aim it at the remote sensor on the TV. 1.Power Press to turn on and off the TV. 1 USB DVD 2.USB Press to switch input source to USB in. 2 21 3.GUIDE Display the guide when you are watching GUIDE CCD MTS/SAP CH.LIST analog or digital channels. 3 22 23 4 PI CT UR E AUDIO ARC FAVORITE 4.CCD(closed caption) Select a closed caption option 24 5 5.PICTURE
Summary of the content on the page No. 9
Installation External Equipment Connections Accessories TV DVD STB CABLE VCR AUD R PICTURE AUDIO PC HDMI TFT-LCD TV INPUT OWNER'S MANUAL MUTE RECALL Please READ this manual carefully before operating your TV, and retain it for future VOL CH reference. MENU EXIT ENTER SLEEP DISPLAY USB PLAY/PAUSE STOP REC REV PREV NEXT REPEAT MTS/SAP FREEZE CH.LIST GUIDE CCD ARC FAVORITE M OD EL: S HL26K HL 32 K Remote control Owner`s manual A
Summary of the content on the page No. 10
Installation External Equipment Connections NOTE: All cables shown are not included with the TV. Choose Your Connection There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some different ways to connect your TV with different input sources. Connecting a VCR To avoid picture noise (interference), leave an adequate distance between the VCR and TV. Connection Opti
Summary of the content on the page No. 11
Installation External Equipment Connections External A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown 2 2 in the figure. L L When connecting the TV to external equipment, match the D DV VI I A AU UD DI IO O 2 2 jack colors (Video = yellow, Audio Left = white, and Audio 1 1 R R Right = red). 1 1 How to use Y Y P Pb b P Pr r L L A AU UD DI IO O R R V VG GA A A AU UD DI IO O V VG GA A 1. Select the in
Summary of the content on the page No. 12
Installation External Equipment Connections Connecting a DTV(digital TV) This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). How to connect Use the TV`s COMPONENT , VGA or HDMI jack for video conne
Summary of the content on the page No. 13
Installation External Equipment Connections Connecting a computer How to connect 1. To get the best picture quality, adjust the VGA graphics card to 1024x768 . 2. Use the TV`s VGA or DVI (Digital Visual Interface)Audio IN port for audio connections, depending on your computer connector. If the graphic card on the computer does not output analog and digital RGB simultaneously, connect only one of either VGA IN or HDMI IN to display the VGA on the TV. If the graphic card on the computer
Summary of the content on the page No. 14
Installation External Equipment Connections HDMI and DVI input When the source device(DVD player or Set Top Box) supports HDMI How To Connect 1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product). 2. No separated audio connection is necessary. How To Use If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p. If the source device does not support Auto HDMI, you need to
Summary of the content on the page No. 15
Installation Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable (not supplied with the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) Owner s Manual 15
Summary of the content on the page No. 16
Installation External Equipment Connections Connecting Headphones You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room. Plug a set of headphones into the 3.5mm HDMI3 IN HDMI4 IN mini-jack socket on the side panel of the set. Note Prolonged use of headphones at a high volume may damage your hearing. You will not receive sound from the speakers when you connect headphones to the system. Power source AC Outlet TO USE
Summary of the content on the page No. 17
Installation Removing the table stand and installing a wall mount bracket HLC26R1 Remove 4X M4 screws securing the Use 4X M6 screws to secure the wall stand to the TV, then remove the stand. bracket (not supplied) to the back of your TV. HLC32R1 Remove 6X M4 screws securing the Use 4X M6 screws to secure the wall stand to the TV, then remove the stand. bracket (not supplied) to the back of your TV. Owner s Manual 17
Summary of the content on the page No. 18
Operation Operation In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an example to help you with the TV operation. There are several options you might need to set up in order for your TV to work properly. Read the instructions that follow. Initial Setup: Set according to the screen display. Switching On/Off the TV set 1. First, connect power cord correctly. 2. Select the viewing source by using INPUT button on the remote control. 3. When fini
Summary of the content on the page No. 19
Operation Channel menu This TV set has two methods to set channels, which are respectively Channel Scan, Channel Skip. In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV to set channel. Note The Channel menu will be only operated in normal TV mode. Video Tuner Antenna Channel Scan Channel Scan Audio Channel Skip 1. Press MENU button and then use / button to select Channel Channel menu. Function 2.
Summary of the content on the page No. 20
Operation Select the desired program 1. Using CH+/- buttons. Press CH+ button to select a channel number in number increasing direction. Press CH- button to select a channel number in number decreasing direction. Note If skip is ON on one channel, press CH+/- button, the channel will not appear. 2. Also can enter channel number directly,eg:2-0. Select the desired sound Press VOL-/+ buttons on the remote or the front of the TV set to adjust the volume level. The range is 0~
