Summary of the content on the page No. 1
TM
-
c
User’s Guide
tion With Touchscreen & Learning Fun
515 Universal LCD Remote Control UC
Summary of the content on the page No. 2
About This User’s Guide - 515 Universal LCD Remote Control. Information in t information co n notice. . Edition © 2000 by Crisp Solutions LLC. All rights reserved. No part of this m, or transmitted in any form or by any means (electronic, mechanical, Trademarks c tive holders. ii ide are the properties of their respe user’s gu Trademarks and registered trademarks of products referred to in this permission of the publisher. photocopying, recording, or otherwise), wi
Summary of the content on the page No. 3
This device complies with Part 15 of the FCC Rules. Operation is • This device may not cause harmful interference • This device must acce pt any Interference received, including inte r iii ference that may cause undesired operation. subject to the following two conditions: Radio Frequency Interference UCommand User’s Guide
Summary of the content on the page No. 4
Chapter 1 1 Introduction ................................ ................................ ............... 1 d ................................ ............................ 1 ................................ .............................. 2 ................................ ........................... 3 - ................................ ................ 3 Chapter 2 5 Getting Sta ................................ ................................ .......... 5 .........................
Summary of the content on the page No. 5
................................ ......... - ..... 35 ................................ ..................... Appendix B 37 Troubleshooting ................................ ................................ ..... v 37 35 UCommand Specifications Appendix A 33 3: Recalling the original LCD panel configuration Figure 3 33 inal LCD Layout Recalling the Orig UCommand User’s Guide
Summary of the content on the page No. 6
Summary of the content on the page No. 7
I NTRODUCTION Congratulations on the purchase of UCommand UC - the easy to use and configure digital remote control. UCommand lets you manage al l your infrared - controlled devices, eliminating the need to search for your various remotes. All you need is the UCommand. This remote control does it all for you! UCommand’s main concept is based on a large and user - friendly touch screen panel. The button s change automatically to display the various devices you wish to control. This uni
Summary of the content on the page No. 8
1 - • - 515, Universal LCD Remote Control • • • If any of the above items are missing or app ear damaged, contact your dealer immediately. Do not throw the shipping - a This section provides an overview of the key features of UCommand. For more information on getting the most from a tures, refer to . • visibility in dim lighting • Adjustable backlight with four levels of ambient light se n sitivity • Extensive, programmable Macr o functions: each macro can • Offers eigh
Summary of the content on the page No. 9
This section provides an overview of UComm and controls. Please refer to the following illustrations to identify UCommand’s components. Refer to Chapter 3 for a n trols. 1 1 Figure 1 - 1: Front and rear view 3 Components Identifying functions. device remote control remote to learn your this eye to enable the remote control at Point your device’s Learning eye the remote. once to power on Tap the LCD panel function you want. the screen on the devices by touching OPEN operate your conf
Summary of the content on the page No. 10
1 - NOTES 4 Introduction Chapter
Summary of the content on the page No. 11
G S TARTED This chapter will guide you through the steps for inserting r UCommand UC - 515 operates on four AAA batteries. Batteries are required before you can operate your mmand. To insert the batteries, refer to the following illustr a tion: Figure 2 - 1: Inserting the batteries battery case. batteries. marking inside the Insert the B. according to the insert the batteries Make sure you the arrow. in the direction of cover by pushing Open the battery A. UCo Power Supply ies
Summary of the content on the page No. 12
2 - NOTE: Average alkaline battery life is approximately 4 - 6 months. If you do not use the remote for extended periods of tim e, please remove the batteries and store them in a cool dry place. Always dispose of used batteries in an environmentally friendly way. When the battery charge is low, the “battery low” icon will be 1 1 Fi gure 2 - 2: The ba t You should replace the batteries with new ones immediately. • Be sure that the positive (+) and negative ( - ) polarities o
Summary of the content on the page No. 13
• k age. • Your device configuration data is stored in on - memory and will be automatically saved when batteries are The LCD (Liquid Crystal Display) touch screen enables you to configure and operate your UCommand with the touch of a finger. To turn the LCD panel on, simply tap t he screen with your finger: 1 1 Figure 2 - 3: Turning the LCD on Touch Screen Precautions Please read the following instructions carefully: • • • Keep the LCD dry. Wipe off any spills imme
Summary of the content on the page No. 14
2 - • Avoid dropping the UCommand unit. • • dampen the cloth slightly before cleaning. Never use u e vices as you would with your regular remote control, set up Using the touch screen is easy. Simply press the screen to acti vate a function. You will hear a beep when you press the button. NOTE: If you don’t hear a beep when you press the screen, you may have deactivated the beep. Press any device button twice to activate the beep function. If you ss the button a little m
Summary of the content on the page No. 15
1 1 Device buttons When you press the device button, g that it is currently selected. Figure 2 - 4: 9 Buttons Screen Touch Panel Layout LCD the button’s icon will appear, indicatin UCommand User’s Guide
Summary of the content on the page No. 16
2 - NOTES 10 Started Getting Chapter
Summary of the content on the page No. 17
O OMMAND - This chapter shows you how to set up UCo m mand, how to automatically configure devices, and how to use a d vanced c Before you start configuring your remote control using the following: • You can map multiple devices to the same device layer. This can be very useful; for example, if you wish to control the TV’s volume using your amplifier, without having to change between e r TV functions from the TV but the volume functions from the amplifier remote. In some rare case
Summary of the content on the page No. 18
3 - - When using the learning function , point your device’s remote control at UCommand’s learning eye . You do not have to power on the device. The ideal distance is about 1 to 2 inches. Refer to the following illustr a tion: Figure 3 - 1: Using the learning eye 12 Eye Learning 1-2 inches Using the Learning Function 515 UC UCommand Operating Chapter
Summary of the content on the page No. 19
After yo u have lined up your remote control with UCommand’s learning eye, you can use the learning function. Follow these i n button for three 1 1 You will hear a to the right. prevents you from accidentally modifying UCommand. until it disappears. 13 Function Learning the Using button in any order Press each number This screen Note: mode enable screen setup will see the beep, and then you seconds. Press the Learn structions: UCommand User’s
Summary of the content on the page No. 20
3 - - n n icon t ton. blinking g nal from your device’s remote control. device that you want to your device’s remote 1 1 first button to be mapp ed. While pointing your R device’s remote control at t REMOTE CONTROL 14 ton. bu press the device’s Power UCommand’s learning eye, POWE The Power button is the UCommand’s LCD buttons. control buttons to You can now start mapping program. Press the button of the , awaiting a si The Power button icon is above t
