Summary of the content on the page No. 1
HEARTH PRODUCTS
KITS AND ACCESSORIES
REFLECTIONS REMOTE CONTROL
P/N 750,251M
REV. A 01/2008
REPLACEMENT KIT
INSTALLATION INSTRUCTIONS FOR THE REFLECTIONS REMOTE CONTROL
REPLACEMENT KIT (KIT NUMBERS: H1454 AND H6977)
GENERAL INFORMATION Step 5. Remove the grate.
Step 6. Remove the ember bed.
This Remote Control Replacement Kit is to be used to replace the
Reflections Electric Fireplace’s Remote Control. The kit components are
Step 7. Remove the fireplace floor.
shown below.
Step 8. Remove
Summary of the content on the page No. 2
Step 9. Locate the fireplace control board (Kit Number H1094) and Step 13. Pull the wire harness completely outside the cavity and remove remove it, including the plastic holders (Refer to Figure 1 ). the flexible wire conduit to expose the wires completely (some early units may have binding tape). If provided, save the flexible conduit to re-use. Step 10. Disconnect the IR cables (ribbon type cables). Refer to Figure 2. Step 14. Leave the A/V cables in place. These cables are not being r
Summary of the content on the page No. 3
Step 15. Locate the TV IR cable and cut about five (5) inches from the end (see Figure 6 ). Step 16. Twist the connector end of the new IR cable to the ends of the old IR cable and wrap securely with duct tape. Refer to Figure 7. Note: Free all cables from one another and pull them individually, as they are replaced. Cut Wire Ties If Provided Pull To Replace Figure 8 Step 17. Pull the TV IR cable until the new cable is out. Unwrap the tape and discard the old cable (see Figure 8 ). Step
Summary of the content on the page No. 4
Push The Remote Receiver Into The Rectangular Slot Bundle New Cables And A/V Cables Together With Tape Figure 10 Step 20. Bundle the new cables and the A/V cables together and wrap with masking tape, or rout them through the flexible conduit if provided. See Figures 11 and 12. Step 21. Tack the wire harness into the side frame and replace the wire harness shield, if provided (see Figure 13 ). Figure 12 Tack Wire Harness Behind Side Frame New Cables Routed Figure 13 Figure 11 NOTE: DIAGRAMS & I
Summary of the content on the page No. 5
Step 22. Place the Control Board against the back wall and attach using the top four (4) outermost holes with the screws and nuts provided. Refer to Figures 14 and 15. Step 23. Plug all connectors into the new Control Board. See Figure 15. Back Wall With Mounting Holes Back Wall With Mounting Holes Figure 14 Blower Power Heater Lamp TV/DVD Attach With Attach With Screws Here Screws Here TV DVD Display Mount The Control Board Using The Screws And Nuts Provided Figure 15 NOTE: DIAGRAMS & ILLUSTR
Summary of the content on the page No. 6
DVD INSTALLATION INSTRUCTIONS Refer to the DVD Replacement Kit Installation Instructions manual (No. 750,250M) for additional aid on the following steps: Step 1. Before installing the DVD player, connect the new DVD player to an electrical outlet and insert the DVD disc into the drawer. Step 2. Disconnect the DVD player and bring it into the fireplace cavity. Step 3. Proceed to connect the A/V cables as labeled. Connect the power cord. Step 4. Place a piece of Velcro on the DVD player eye a
Summary of the content on the page No. 7
NOTE: THIS PAGE INTENTIONALLY LEFT BLANK. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7
Summary of the content on the page No. 8
The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2007 by LHP 1110 West Taft Avenue P/N 750,251M REV. A 01/2008 Orange, CA 92865 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8
