Summary of the content on the page No. 1
iQ SERIES
PERFORMANCE DATA AND HARDWARE INFO
iQ 10/15
Summary of the content on the page No. 2
NOTES: Arraying Comb filtering is a phenomenon, which cannot be cured by equalisation. Small alterations to loudspeaker positions can have the effect of minimising problematic combing frequencies. Arrays should be constructed so that the individual coverage patterns of each loudspeaker combine with minimal overlap. The design of the iQ 10/15 cabinet greatly simplifies the creation of effective arrays, allowing seamless wide (120 degree) horizontal coverage using two loudspe
Summary of the content on the page No. 3
Dimensions 540.0 680.0 1116.0 7
Summary of the content on the page No. 4
SECUR ET – VEB Eyebolt The Tannoy iQ 10/15 loudspeaker can be flown with high quality VEB M10 eyebolts with collar to BS4278:1984. The loudspeakers are equipped with internal steel braces, which also double as the flying points, and accept VEB M10 eyebolts. To install the VEB M10 eyebolts remove the original M10 counter sunk screws from the locations you wish to install the VEB M10 eyebolts. Then replace these counter sunk M10 screws with the VEB M10 eyebolts. The kelping brac
Summary of the content on the page No. 5
™ SINGLE iQ SUSPENSION TRUSS (By ATM ) The iQ suspension truss is an economical solution to suspending a single purpose loudspeaker array from two or three fixed structural attachment points. The iQ Suspension Truss is designed to hold the loudspeakers at the optimum splay angle to optimize cluster performance. Most Suspension Trusses are equipped with two suspension rails with multiple attachment holes that travel from front to back across the top of the array, allowing manipulation o
Summary of the content on the page No. 6
Typical Suspension Truss applications – 2 x iQ 10/15 2 x iQ 10C & 2 x iQ 10/15
Summary of the content on the page No. 7
Performance Data FREQUENCY RESPONSE Anechoic System Frequency Response, 1 watt (MF/HF) @ 1 metre on axis INPUT IMPEDANCE Impedance (Passive MF/HF only)
Summary of the content on the page No. 8
High Frequency (Tri-amp option) Anechoic Frequency Response, 1 watt (HF) @ 1 metre on axis Impedance (HF only)
Summary of the content on the page No. 9
Mid Frequency (Tri-amp option) Anechoic Frequency Response, 1 watt (MF) @ 1 metre on axis Impedance (MF only) A comprehensive range of measurements including off axis frequency response curves, octave & third octave polar diagrams (single & two cabinet arrays) and beamwidth plots as well as Ease™ data can be downloaded from http://www.tannoy.com/
Summary of the content on the page No. 10
Technical Specifications Frequency Response (1) +/- 3dB 49Hz - 19kHz -10dB Point 43Hz o o Nominal Dispersion 60 x 40 (H x V) Driver Compliment MF/HF – 1 x 250mm (10”) PowerDual™ LF - 1 x 380mm (15”) Configurations Bi-amp (standard) - LF & Passive MF/HF Tri-amp (optional) Components LF Midrange High Frequency Frequency Band (3) 43Hz – 180Hz 180Hz – 2.77kHz 2.77kHz – 19kHz Sensitivity (1) 101dB 107dB 110d
Summary of the content on the page No. 11
iQ 10/15 Service Parts and Accessories Part Number Description 7900 0607 Driver Kit Type 2519 (MF) 7900 0609 Recone Kit Type 2519 (MF) 7900 0608 Driver Kit Type 0278 (HF) 7900 0610 Diaphragm Type 0278 (HF) 8001 2820 VEB – Secur ET – Eyebolts M10 8000 3630 TDX1 Digital System Controller 60-250V – UK 8000 3631 TDX1 Digital System Controller 60-250V – EUR 8000 3632 TDX1 Digital System Controller 60-250V – USA 8000 0727 TDX2 Digital loudspeaker management system 60-250V - UK
Summary of the content on the page No. 12
Decla ration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipm
