Summary of the content on the page No. 1
VIDEO CASSETTE PLAYER
-
HR P128EE
-
HR P125EE
OPERATE STANDBY
NTSC
MADE IN JAPAN PLAYBACK
VIDEO AUDIO B.E.S.T.
SP/LP/EP ON PAL TV
NTSC3.58
VIDEO CASSETTE B.E.S.T. LP/EP
NTSC4.43
PLAYER
HR-P128
PAL NTSC
INSTRUCTIONS
LPT0002-0H1B
ENGLISH
Summary of the content on the page No. 2
Table of contents Precautions Thank you for purchasing this JVC video cassette player. To The rating plate and the safety caution are on the rear of the unit. ensure optimum performance of this unit, please read this instruction manual thoroughly. WARNING: DANGEROUS VOLTAGE IN- SIDE Precautions ...........................................................................2 WARNING: TO PREVENT FIRE OR SHOCK Controls and terminals ..........................................................3 Wireless r
Summary of the content on the page No. 3
Controls and terminals Front panel 1 24 3 5 OPERATE STANDBY NTSC MADE IN JAPAN PLAYBACK VIDEO AUDIO B.E.S.T. SP/LP/EP ON PAL TV NTSC3.58 VIDEO CASSETTE B.E.S.T. LP/EP NTSC4.43 PLAYER HR-P128 %$! #098 76 1 OPERATE button ! Colour System Output switch To turn the power on and off (standby mode). Select to watch an NTSC tape. 2 Cassette loading slot @ Mode indicators Load the video cassette here. OPERATE indicator • Lights when the power turns on. 3 Rewind 1 button • Blinks while a cassette is
Summary of the content on the page No. 4
Wireless remote control When using the remote control for operation of the video cassette player, make sure that it is pointed at the remote sensor window. OPERATE STANDBY NTSC VIDEO AUDIO MADE IN JAPAN PLAYBACK B.E.S.T. SP/LP/EP ON PAL TV NTSC3.58 VIDEO CASSETTE B.E.S.T. LP/EP NTSC4.43 PLAYER HR-P128 You can also use the player’s remote control to operate a JVC television. 1 Transmitting window 1 2 TV channel –/+ buttons 3 TV VOLUME –/+ buttons TV - TVCH + OPERATE 4 TV/VIDEO (Player)
Summary of the content on the page No. 5
Connections Make sure that the power to the video cassette player and TV is off before making the following connections. Connection A 10- 40 32 RF OUT IN OUT AUDIO K G ANT. VIDEO IN 1- Connection B Note: If you put a TV set directly on this VCP or install it too close to a TV set, noise may occur. If this noise occurs, separate the VCP and the TV set. Connection A (basic) Connection B In order to use the video cassette player it must be connected For connection of a TV that has VIDEO/AUDIO IN/OU
Summary of the content on the page No. 6
40 32 Setting the video channel The video cassette To watch videos on your TV, it must be set to the same UHF Inserting a cassette channel as the video cassette player. This channel is used as the video channel. This video cassette player has been preset to UHF channel 36. Note: OPERATE STANDBY NTSC MADE IN JAPAN PLAYBACK B.E.S.T. VIDEO AUDIO SP/LP/EP ON PAL TV NTSC3.58 • When you have connected the VIDEO/AUDIO OUT termi- VIDEO CASSETTE B.E.S.T. LP/EP PLAYER NTSC4.43 HR-P128 nals of this vid
Summary of the content on the page No. 7
Playback NTSC, PAL and MESECAM video tapes can be played back on NTSC Playback on PAL TV this video cassette player. Refer to the “Colour system output mode selection” section for details. • The vertical size of the playback picture will shrink and some picture “noise” may appear on the screen. • The playback picture may roll. In this case adjust the picture Before proceeding: with the TV’s vertical hold knob (with some TV’s this adjust- ment may not be possible). • The colour of the playback pi
Summary of the content on the page No. 8
Playback features Slow motion playback B.E.S.T. picture system Slow motion playback is 1/6 of the normal playback speed. The The B.E.S.T. (Biconditional Equalized Signal Tracking) system sound will be cut during slow motion playback. checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible During playback: recording and play back pictures. Press the Pause 8 button for 2 seconds. Press the B.E.S.T. button. 1 1 The B.E.S.T indicator wil
Summary of the content on the page No. 9
Playback features (cont’d) Recording Use the following procedure to record TV programmes on a Tracking adjustment blank video tape. Automatic tracking is adjusted each time a cassette is inserted in the video cassette player, you may wish to adjust tracking Before proceeding: manually during playback. Manual tracking • To record TV programmes, the video cassette player must be connected to the TV as shown in connection B of the 1 Press the remote control’s AUTO button. “Connections” section. • T
Summary of the content on the page No. 10
Editing Troubleshooting Editing To/From Another Recorder Problem Check point No power Is the power cord plugged in? Player Is the power turned on? Tape cannot be ejected Was the video cassette player’s ¤ button pressed? No picture Is the TV set to the video 10- 40 channel? 32 IN OUT RF OUT AUDIO Is a cassette loaded? K G ANT. VIDEO IN Are the connections correct? 1- No colour Set the Colour System Out- put switch according to the recorded tape system. When playing a MESECAM Audio/Video signals t
Summary of the content on the page No. 11
Specifications Format ................................ VHS Standard Video recording system ..... Rotary, slant azimuth two-head helical scan system Rotary heads ...................... 2 video heads RF output ........................... System G/K type modulation UHF ch 32 – 40 adjustable (preset ch 36) Recording (line input) ......... PAL, SECAM (MESECAM tape) NTSC 3.58, NTSC 4.43 Playback (line output) ........ PAL, SECAM (MESECAM tape) NTSC 3.58 NTSC 4.43 Simulated PAL (NTSC tape) Video Line i
Summary of the content on the page No. 12
HR-P128/125EE VICTOR COMPANY OF JAPAN, LIMITED Printed In Japan C COPYRIGHT 1997 VICTOR COMPANY OF JAPAN, LTD. 0997 YSV*YP*YP
