Summary of the content on the page No. 1
3
CONTENTS
SAFETY FIRST 2
Mini DV/S-VHS
Safety Precautions.............................2
Some Do's And Don'ts .....................4
VIDEO CASSETTE RECORDER
QUICK SET UP GUIDE 5
CHECK THE CONTENTS .................. 5
INSTALLATION ................................6
AUTO SET UP ..................................8
T-V LINK 11
HR-DVS1EK
T-V LINK Functions ......................... 11
BASIC OPERATIONS 12
Playback .........................................12
Recording ..................................
Summary of the content on the page No. 2
SAFETY FIRST 2 Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. IMPORTANT n Please read the various precautions on p. 2 – 4 of this instruction manual before installing or operating the recorder. n It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright i
Summary of the content on the page No. 3
3 CAUTION n To avoid electric shock or damage to the unit, first firmly insert the small end of the mains power cord into the recorder until it is no longer wobbly, and then plug the larger end of the mains power cord into a mains outlet. n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. n Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire h
Summary of the content on the page No. 4
SAFETY FIRST (cont.) 4 Some Do's And Don'ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnec- tions between pieces of equipment) are
Summary of the content on the page No. 5
T V – M E N U 3 S + T T O A R V T G K P O R QUICK SET UP GUIDE 5 Dear Customer, Thank you for purchasing this JVC Video Cassette Recorder. Please use this QUICK SET UP GUIDE to help you to set up your video cassette recorder. CHECK THE CONTENTS 1 CHECK ALL THE CONTENTS SHOWN BELOW Video Cassette Recorder VCR TV SAT AUDIO A/B TV/VCR – –:– – STANDBY/ON ENTER/ENTREE T W 1 2 3 2 DV VHS FADE/WIPE EFFECT ON/OFF 4 5 6 PULL - OPEN PULL - OPEN VPS/PDC DAILY/QTDN. WEEKLY/HEBDO 7 8 9 0000 AUX 4 0 START STO
Summary of the content on the page No. 6
QUICK SET UP GUIDE (cont.) 6 INSTALLATION 2 CONNECT VIDEO RECORDER TO TV Place the recorder on a stable, flat surface. Back of TV RF Cable (provided) TV Aerial Cable (not provided) 21-pin SCART Cable (provided) 21-pin AV input Aerial connector connector (SCART) AV1 IN/OUT (L-1) S OUT AC IN (DV/VHS) ANT. IN AUDIO OUT AV1 OUT (DV/VHS) L COMP. Y/C R AV2 IN/DECODER (L-2) Mains outlet RF OUT Back of Recorder AV1 OUT switch Mains power inlet ATTENTION: You can not use the recorder connected to your TV
Summary of the content on the page No. 7
7 Back of TV Aerial connector S-Video cable (not provided) S-VIDEO IN connector Audio cable (not provided) AUDIO IN connectors Mains outlet Mains power inlet AV1 IN/OUT (L-1) S OUT AC IN (DV/VHS) ANT. IN AUDIO OUT AV1 OUT (DV/VHS) L COMP. Y/C R AV2 IN/DECODER (L-2) RF OUT Back of Recorder RF Cable (provided) S-VIDEO CONNECTION NOTES: To connect to a TV with S-VIDEO/AUDIO IN connectors . . . c You can obtain high-quality S-VHS pictures. 1– Connect the aerial, recorder and TV as per "AV CONNEC- c
Summary of the content on the page No. 8
3 QUICK SET UP GUIDE (cont.) 8 AUTO SET UP 3 SET THE TUNER CHANNELS, CLOCK AND GUIDE PROGRAM NUMBERS The Auto Set Up function sets the tuner channels, clock and VIDEO Plus+ assigned Guide Program numbers automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet. Before performing the following procedure, make sure that: n the TV aerial cable is connected to the recorder. n the mains
Summary of the content on the page No. 9
3 9 PRESET DOWNLOAD SET THE TUNER CHANNELS BY DOWNLOADING FROM YOUR TV, CLOCK AND GUIDE PROGRAM NUMBERS When you connect the recorder and your TV via fully-wired 21-pin SCART cable (Z pg. 6), you can set the recorder's tuner channels by downloading preset data from your TV instead of using the Auto Set Up function (Z pg. 8). After downloading is completed, the recorder sets the clock and VIDEO Plus+ assigned Guide Program numbers automatically. For details, refer to the instruction manual for yo
Summary of the content on the page No. 10
QUICK SET UP GUIDE (cont.) 10 Auto Set Up/Preset Download results appear on the display panel When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed after the OK button is pressed in item 3 on page 8 or A after performing item 2 on page 9. When auto channel set has been completed successfully but auto clock set has not, "(PR)1" B will be displayed after the OK button is pressed in item 3 on page 8 or after performing item
Summary of the content on the page No. 11
T-V LINK 11 Direct Rec You can start recording the programme that you are watching T-V Link on your TV with simple operation. Press and hold RECORD and press PLAY on the remote control, or press RECORD on the recorder. Follow the procedure below to use this function. Functions TURN ON THE RECORDER When you connect the recorder and your TV via a fully-wired 21-pin SCART cable (Z pg. 6), the following functions are Press . available. You can use these functions only with a TV offering T-V Link, et
Summary of the content on the page No. 12
FF PLAY PLAY 3 BASIC OPERATIONS 12 The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. Playback LOAD A CASSETTE Turn on the TV and select the AV mode. Making sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette 1 is pointing towards the recorder. Don’t apply too much pressure when inserti
Summary of the content on the page No. 13
h d r c a r w a r e o s F y a l P n o w i t o l o S m 13 Still High-Speed (Turbo) Search ACTIVATE HIGH-SPEED SEARCH During playback or still, turn the SHUTTLE ring all the way to the right for forward high-speed search, or to 1 the left for reverse high-speed search. Releasing SHUTTLE resumes still picture playback. OR During playback or still, press FF for forward high- speed search, or REW for reverse high-speed search. To resume normal playback, press PLAY. NOTES: c Refer to the SHUTTLE ring
Summary of the content on the page No. 14
3 BASIC OPERATIONS (cont.) 14 DISPLAY Mode Setting (DV Deck) Set "DISPLAY" to "ON" to display the date and time of the original recording. T W 1 Press MENU to access the 1 2 3 DV MODE SET 2 SOUND MODE 32kHz Main Menu screen. 32kHz MODE SOUND1 4 5 6 2 Move the highlight bar DISPLAY ON (pointer) to "DV MODE AUDIO REC NICAM 7 8 9 SET" by pressing %Þ, then 4 0 press OK or #. 3 Move the highlight bar (pointer) to "DISPLAY" by [5°] = pressing %Þ, then press [MENU] : EXIT OK or # to select "ON" or 1 D
Summary of the content on the page No. 15
TV PROG PLAY DV 3 15 TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder. Recording LOAD A CASSETTE Insert a VHS (or S-VHS) cassette with the record safety Turn on the TV and select the AV mode. tab intact, or a Mini DV cassette with the erase 1 protection switch set to "REC". c The recorder power comes on automatically. 6 7 7 The counter is reset to 0:00:00 (VHS deck only). SELECT DECK 1 1 Press
Summary of the content on the page No. 16
TV PROG 3 BASIC OPERATIONS (cont.) 16 Accidental erasure prevention c VHS/S-VHS To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape. Record safety tab c Mini DV To prevent accidental recording on a recorded cassette, set its erase protection switch to "SAVE". To record on it later, set the switch to "REC". – –:– – Erase protection T W 1 2 3 switch 2 4 5 6 7 8 9 4 0 0000 Recording Resume Function If there is a pow
Summary of the content on the page No. 17
17 Record One Programme Tape Remaining Time While Watching Another (VHS Deck Only) SELECT PRESET TO WATCH DISPLAY REMAINING TIME Once recording is in progress, all you need to do is to Press – –:– – until the time remaining on the tape set the preset controls on the TV for the station you appears. 1 wish to view. 1 c The display panel shows the tape remaining time c The programme selected with the TV’s preset controls with " " displayed. appears on the TV screen while the one selected with c By
Summary of the content on the page No. 18
3 BASIC OPERATIONS (cont.) 18 With VIDEO Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. VIDEO Plus+ ACCESS VIDEO PLUS+ SCREEN Press PROG. VIDEO PLUS+ Timer 1 Programming [0 – 9] : VIDEO PLUS+ [+/–] : EXPRESS PROGRAMING [PROG] : EXIT Before performing VIDEO Plus+ Timer Programming: c Make sure that the recorder's built-in clock is set The front display panel looks like this: properly. c Select the
Summary of the content on the page No. 19
19 Satellite Receiver Users SET TAPE SPEED To timer-record a satellite broadcast using VIDEO Plus+: Press SP/LP ( ) to set the tape speed. 1 Set "AV2 SELECT" to the appropriate mode. (Z pg. 48) 2 Perform steps 1 – 7. 4 3 Set the satellite receiver to the appropriate channel before the selected programme begins. SET PDC MODE 4 Leave the satellite receiver's power on. Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ 5 PDC" is lit on the display panel, PDC is s
Summary of the content on the page No. 20
DAILY STOP+/– DATE+/– 3 BASIC OPERATIONS (cont.) 20 If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme. Express Timer ACCESS VIDEO PLUS+ SCREEN Programming Press PROG. 1 Before performing Express Timer Programming: c Make sure that the recorder's built-in clock is set properly. ACCESS PROGRAMME c Select the recording deck by pressing VHS or DV. SCREEN c Insert a VHS (or S-VHS) cassette with th
