Summary of the content on the page No. 1
Summary of the content on the page No. 2
Table of contents Selecting music ............................................................................................................8 Congratulations ............................................................................................................2 Box contents.................................................................................................................2 Setting and using stream presets.......................................................................
Summary of the content on the page No. 3
This plug will fit into the outlet only one way. This is a antenna discharge unit, size of grounding conductors, Safety precautions (continued) safety feature. If you are unable to insert the plug fully into location of antenna discharge unit, connection to ground- FCC Warning the outlet, try reversing the plug. If it should still fail to fit, ing electrodes, and requirements for the grounding elec- This equipment may generate or use radio frequency contact your electrician to replace your obso
Summary of the content on the page No. 4
Connecting the DT-7000S to your audio system Use the cables supplied with the DT-7000S to make these connections. About the RS-232C connection: The RS-232C connection is provided to allow the DT-7000S to be controlled by compatible 3rd-party control systems. Kenwood recom- mends that this connection only be used by experienced professional system installers. DO NOT connect the RS-232C connection to a computer—it is NOT COMPATIBLE with person- al computers. 4 DT-7000S Instruction Manual
Summary of the content on the page No. 5
Finding a location for the optional Kenwood CX-SRH30 antenna Due to the paths of the SIRIUS satellites Use this map as a general placement guideline—some experimentation may be needed to obtain A. over the US, the best location for the the best reception in your particular situation. See pg. 12 Antenna Signal, for more information antenna will depend on what part of the about using the antenna signal screen to aim the antenna. country you live in, the orientation of your home, and the locations
Summary of the content on the page No. 6
Controls and Features Note: Buttons on the unit and remote with the same name have the same function. POWER Button (unit only): STANDBY Indicator (unit only): Turns the DT-7000S on and puts it into the Standby mode. Illuminates when the DT-7000S is in the Standby mode. Power Off/On Buttons (remote only): Remote Control Receiver: Emit discrete codes to turn the DT-7000S off and on. Receives signals from the included IR remote control. Category Jog Dial (unit)/CAT Buttons (remote): DIRECT Button:
Summary of the content on the page No. 7
Installing batteries in the remote 1. Remove the battery cover as shown in diagram #1 (right). 2. Install two AAA batteries as shown in diagram #2 (right). •Observe the polarity markings on the inside of the battery compartment 3. Replace the battery cover. Using the remote Basic operation • The supplied batteries are for operational checks, and may not last as long as After you have acti- alkaline batteries. vated your SIRIUS subscription, the • If the remote-controllable distance begins to
Summary of the content on the page No. 8
• After you make your selection, the display will revert to the Normal Operation screen Selecting entertainment Note: In the Stream List, Artist List and Song List modes, if you don’t want to make a In addition to the Normal Operation and Category Select screens, the DT-7000S has selection, press the SETUP button to exit the mode and return to the Normal Operation three ways to search for and select entertainment: by stream, by artist, and by song. screen for the active stream. Selecting ente
Summary of the content on the page No. 9
the presets. Each time you change a preset its number will appear on the button on the unit.) display and the stream will play. • If you make a mistake, use the CH Option 2: Press the ENTER button. The buttons to move the cursor to the left Preset List Screen will of the letter you want to delete, and appear on the display, listing press the DELETE button. all of the stream presets Completed name 6. Repeat Step 5 to complete the name that have been programmed (top, right). in all 4 banks (right)
Summary of the content on the page No. 10
4. When one (or more) of the selected songs is playing on any stream, an alert screen will be 1. While in the Setup Mode, turn the superimposed over the data on the original screen (below). CATEGORY jog dial (unit) or press the CAT buttons (remote) until the Auto • The number on the screen will Clock Setup screen appears (right). count down from ‘10’ to ‘0’. 2. Turn the CH/PRESET jog dial (unit) To hear the song, press the ENTER or press the CH buttons (remote) Auto Clock Setup Screen button bef
Summary of the content on the page No. 11
5. When the display shows the correct Sleep Timer hour and minute, press the ENTER You can program the DT-7000S to play for 30 or 60 minutes and then automatically turn button to turn the alarm on. itself off. 6. Press the MEMO button to save your 1. While listening to SIRIUS, press the ENTER button to enter the Stream List mode. settings. The Step 2—Set Stream 2. Then hold the ENTER button for at screen will appear (right). Step 2—Set Stream Screen least 1 second. The Timer Setup 7. Use the CH
Summary of the content on the page No. 12
1. While in the Setup Mode, turn the Lock Code Setup CATEGORY jog dial (unit) or press the If you have locked any streams in the Channel Lock mode, you will need to enter a 4- CAT buttons (remote) until the digit lock code to unlock them. The factory default lock code is “1 1 1 1”. Startup Mode screen appears (right): You can change the Lock Code to your own preference: 2. Use the CH/PRESET jog dial (unit) or 1. While in the Setup Mode, turn the the CH buttons (remote) to highlight Startup Mode
Summary of the content on the page No. 13
Troubleshooting guide Problem Possible Cause Solution No power on DT-7000S (display not illuminated) Power cord is not properly connected Make sure the power cord is properly connected Audio and/or digital cable is not properly connected Make sure cable is properly connected No sound Incorrect input selected on receiver/controller Select the receiver/controller input that the DT-7000S is connected to Check the Antenna Signal screen (see page 12); Signal is weak or can’t be found Change the ant
Summary of the content on the page No. 14
14 DT-7000S Instruction Manual
Summary of the content on the page No. 15
15 DT-7000S Instruction Manual
Summary of the content on the page No. 16
