Summary of the content on the page No. 1
SA-25
™
“STAND-AER ”
STAND ON AERATOR
(S.N. 173 and Up)
Operator’s Manual and Parts List
A Division of Schiller-Pfeiffer, Inc.
www.classen-mfg.com
1028 Street Road • Southampton, PA 18966
Toll Free: 1-877-596-6337 • Fax: 1-215-357-8045
Summary of the content on the page No. 2
TABLE OF CONTENTS SAFETY INSTRUCTION SAFETY INSTRUCTION MANUAL . . . . . . . . . . . . . . . . . . 2 MANUAL INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction GENERAL SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . 2 This aerator is built to the highest standards in the industry. OWNER/USER NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 However, carelessness or operator error may result in serious USER EXPERIENCE AND QUALIFIC
Summary of the content on the page No. 3
mount), and raise platform. Once platform is raised and User Clothing secured in the up position, you have access to the tines. DO NOT operate the aerator while wearing sandals, tennis When you are done maintaining the tines, lower the platform, shoes, or shorts. Always wear long non-baggy pants. Wear and re-secure the 3/8” snap lock pin. high-top leather work boots with thick, textured tread at all times. Hard or smooth soled shoes are too slippery for a good Work Area Conditions and Inspectio
Summary of the content on the page No. 4
• Keep all shields and covers in place. Operating During Zero-Radius Turns • Keep hands, feet, and clothing away from moving parts. During zero-radius turns (when one aerator wheel rotates backwards while the other is moving forward) drive extra • Do not touch engine or muffler while engine is running or slowly to reduce the possibility of losing traction or control. soon after it is stopped. These areas can be so hot as to cause severe burns. Fuel Safety • Be alert for traffic when crossing roa
Summary of the content on the page No. 5
unit. Refill the reservoir as necessary. Check for any fluid OPERATING INSTRUCTIONS leaks, and check the reservoir level. Add fluid if necessary. The transmission is now ready for operation. Check the Inspect aerator before each use reservoir daily for proper fluid level. It should be filled to the top, or about 4 quarts. Do not use aerator if any parts are not maintained in good operating condition. Examine the moving parts prior each use. Decals Look for excessive wear, bald drive tires or wo
Summary of the content on the page No. 6
Main Frame Assembly SA-25 STAND ON AERATOR 6
Summary of the content on the page No. 7
QTY/PER QTY/PER KEY PART NO. SHEET DESCRIPTION KEY PART NO. SHEET DESCRIPTION 41 500026 4 3/8" CLEVIS YOKE 1 100074 3 DECAL, "CLASSEN" 42 400201 1 CENTER PULLEY GUARD 2 500135 4 1/2" x 2-1/2" BOLT 43 400215 1 LINKAGE ARM HANDLE 3 300121 1 WEIGHT BAR 44 500149 1 1/2" x 2" BOLT 4 500006 7 1/2" LOCK WASHER 45 500019 1 SMALL HANDLE SPRING 5 500106 5 1/2" NUT 46 400210 1 THROTTLE PLATE 6 400208 1 SA-25 MAIN FRAME 47 400211 1 PLATFORM 7 500129 22 3/8" NUT 48 500065 4 COMPRESSION SPRING 8 500130 22 3/8
Summary of the content on the page No. 8
Power Train Assembly SA-25 STAND ON AERATOR 8
Summary of the content on the page No. 9
QTY/PER QTY/PER KEY PART NO. SHEET DESCRIPTION KEY PART NO. SHEET DESCRIPTION 41 500101 8 5/16" NUT 1 500146 4 3/8" x 1-1/2" BOLT 42 500115 8 5/16" LOCK WASHER 2 500042 20 3/8" FLAT WASHER 43 500163 8 5/16" x 3/4" CARRIAGE BOLT 3 100377 1 13 HP HONDA ENGINE 44 500229 2 5 mm KEY 4 500130 34 3/8" LOCK WASHER 45 300129 2 SPACER 5 500129 38 3/8" NUT 46 100418 2 SPLIT LOCK COLLAR 6 500134 8 3/8" x 1-1/4" BOLT 47 500233 1 3/8" x 1-1/2" FINE BOLT 7 100374 1 LEFT SIDE HYDRAULIC PUMP 48 500148 1 3/8" HEA
Summary of the content on the page No. 10
Handle and Control Assembly SA-25 STAND ON AERATOR 10
Summary of the content on the page No. 11
QTY/PER QTY/PER KEY PART NO. SHEET DESCRIPTION KEY PART NO. SHEET DESCRIPTION 41 100421 1 DECAL, "RIGHT, FORWARD-REVERSE" 1 500043 16 3/8" x 1" BOLT (NOT SHOWN) 2 500029 2 1/4" x 3/4" BOLT 42 100422 1 DECAL, "LEFT, FORWARD-REVERSE" 3 300137 2 FILTER MOUNT BRACKET (NOT SHOWN) 4 500130 16 3/8" LOCK WASHER 43 100423 1 DECAL, "TINE, UP-DOWN" (NOT SHOWN) 5 500129 16 3/8" NUT 44 100424 1 DECAL, "THROTTLE, FAST-SLOW" 6 500137 4 1/4" LOCK WASHER (NOT SHOWN) 7 100480 2 FILTER MOUNT 45 100055 1 DECAL, SE
Summary of the content on the page No. 12
Tine Frame Assembly SA-25 STAND ON AERATOR QTY/PER KEY PART NO. SHEET DESCRIPTION 1 400204 1 TINE MOUNT FRAME 2 500041 12 3/8" LOCK NUT 3 100155 4 BEARING w/COLLAR, 1"-3 BOLT 4 500043 6 3/8" x 1" BOLT 5 300123 2 TINE SPACER 6 200009 2 SPROCKET w/1" HUB, 40 x 30 7 700031 2 TINE DISC SHAFT ASSEMBLY 8 500003 2 1/4" HALF MOON KEY 9 100032 36 TINE 10 500146 6 3/8" x 1-1/2" BOLT 11 100383 2 BEARING w/SET SCREWS, 1"-3 BOLT 12 100384 4 NYLON WASHER 13 500169 72 5/16" LOCK NUT 14 400221 2 TINE DISC w/HUB
Summary of the content on the page No. 13
Hoses and Adapters Description SA-25 STAND ON AERATOR QTY/PER KEY PART NO. SHEET DESCRIPTION 1 600062 2 HOSE #1 (6C2AT x 23) w/1-6MJ-6MB, 2-6G-6FJX, 1-6MJ-6MB90 2 600063 2 HOSE #2 (6C2AT x 7-1/2) w/1-6MB-6MJ, 2-6G-6FJX, 1-6MJ-8MP90, 1-1 x 1/2 BLACK BUSHING 3 600057 1 HOSE #5 (8C2AT x 12) w/1-8MB-8MJ, 1-8G-8FJX, 1-10MB-8MJ, 1-8G-8FJX45 4 600051 1 HOSE #6 (8C2AT x 10) w/1-8MB-8MJ, 2-8G-8FJx45, 1-10MB-8MJ 5 600058 1 HOSE #7 (8C2AT x 12) w/1-8MB-8MJ, 2-8G-8FJX45, 1-10MB-8MJ 6 600052 1 HOSE #8 (8C2AT
Summary of the content on the page No. 14
Hydraulic Hoses Description SA-25 STAND ON AERATOR 14
Summary of the content on the page No. 15
See the complete line of Turf Care Products from CLASSEN SOD CUTTERS COMPACT AERATORS SC-12 CA-18H SC-18 CA-18B SC-20 SPLIT DRIVE AERATORS SC-24 TA-25D TURF RAKES TA-17D TR-20H SA-25 TR-20B TURF AERATORS TR-20MH TA-19D TR-20MB TA-26D TR-20SH TOW/3PT AERATORS TR-20SB 48RT TRC-20H 60RT TRC-20B 72RT TRS-20H 3 PT AERATORS TRS-20B 48R TURF SEEDERS 60R TS-20H 72R TS-20B 84R TSS-20H TSS-20B TRAILERS AST SAT Classen reserves the right to make changes or add improvements to its products at any time with
Summary of the content on the page No. 16
A Division of Schiller-Pfeiffer, Inc. www.classen-mfg.com 1028 Street Road • Southampton, PA 18966 Toll Free: 1-877-596-6337 • Fax: 1-215-357-8045 TWO YEAR LIMITED WARRANTY Effective April 1, 2007 For the period of two years from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser free of charge, any part or parts found upon the examination of our factory authorized service station, or by the factory in Norfolk, Nebraska, to be defective in material or work
