Summary of the content on the page No. 1
Owner’s/Installation Manual
7" Color LCD Monitor
Model: M125C
For Technical Assistance, please call (800) 638-3600,
or visit www.magnadyne.com
Summary of the content on the page No. 2
Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning / Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Monitor Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Monitor Features and Controls 10 11 1 2 3 4 5 6 7 8 9 1. LCD Screen 6. Brightness Button (Increase): Press this button to increase the screen’s brightness. 2. IR Sensor: Receives signal from the Note: When the menu is displayed, press remote control. this button to adjust the selected menu 3. LED Power Indicator: item. A red LED indicates the vehicle’s ignition 7. CH- Button (Menu Item Selection): is “On” and the monitor is in the “stand- Press this button to select a menu item by” mode. When th
Summary of the content on the page No. 4
Remote Control Functions MUTE POWER 1 7 8 CH 2 3 MENU CH 4 9 MODE CALL TIMER 5 10 LANG SYS SEL 6 11 12 1. Mute: Push to "Mute" the volume. 9. CALL: Press to close the menu. 2. : Press this button to select between 10. TIMER: Press to select the shut off time. a Mirror or Normal screen image. When the timer expires the monitor will automatically shut off. : Press this button to flip the screen image vertically. 11. SEL: Press this button to select a video sources (CAM1, CAM2, CAM3 and DVD)
Summary of the content on the page No. 5
General Operation Camera View Selection and A/V Input: Left Side Camera: The left side view camera (CAM1) is designed to automatically turn on whenever the vehicle’s left turn signal is activated. Right Side Camera: The right side view camera (CAM2) is designed to automatically turn on whenever the vehicle’s right turn signal is activated. Rearview Camera: The rearview camera (CAM3) is designed to auto- matically turn on whenever the vehicle is placed into reverse gear. Video Input: Manually s
Summary of the content on the page No. 6
General Operation (continued) Monitor Adjustment The monitor has three basic menus: Picture, Option and System. To scroll through the three basic menus continuously press the MENU button. Picture Menu PICTURE Press the Menu button on either the monitor front VOLUME 35 panel or remote control until the PICTURE menu BRIGHT 40 screen is displayed. Use the buttons on the CONTRAST 50 remote to scroll through the menu items and select COLOR 50 from the menu items: VOLUME, BRIGHT, CONTRAST, SHAR
Summary of the content on the page No. 7
Front Panel Video Input Yellow RCA: Video (Cable Not Supplied) Auxiliary Video Input You can connect the video output signal of a digital camera, camcorder or video device. Select the auxiliary video input mode by pressing the SEL button on the monitor until DVD appears in the display. Cable Suggestions: Radio Shack #42-2551 or #42-2483. Technical Specifications • 7” TFT-LCD color monitor • Audio output: 1 watt • Front speaker • Power supply: automobile storage battery (12-32V) • Power consumpti
Summary of the content on the page No. 8
Wiring Diagram Red Wire: 12 Volt Switched (DC 12~32V) 2 Amp Black Wire: Ground (GND) White Wire: Left Trigger (LEFT TRIG) Gray Wire: Right Trigger (RIGHT TRIG) Green Wire: Rear Trigger (REAR TRIG) 1. +12 Volts 5. Ground 2. N/A 4. Video CAM3 3. Audio (Green Connector) C125 (Rearview) 1. +12 Volts 5. Ground CAM2 2. N/A 4. Video (Gray Connector) 3. N/A C-SDR (Right Side) 1. +12 Volts 5. Ground CAM1 (White Connector) 2. N/A 4. Video 3. N/A C-SDL (Left Side) 8 LEFT TRIG RIGHT TRIG REAR TRIG
Summary of the content on the page No. 9
Installation Instructions The monitor can be mounted via a pedestal-mount, U-support bracket or a flush-mount. Pedestal Mounting the Monitor 1. Loosen the thumb wheel on the base support so the nut attached to the thumb wheel can slide into the monitor’s mounting channel. 2. Slide the thumb wheel nut into the channel on the back of the monitor. 3. Position the monitor to the desired height and tighten the base support thumb wheel. 4. Adjust the tilt lever. 5. Use the double-sided foam (supplie
Summary of the content on the page No. 10
Installation Instructions Flush Mounting the Monitor 1. Locate a suitable location for mounting the monitor (In-Dash, In-Wall, Headrest, etc.). Then cut a 7-1/8" (W) x 4-7/8" (H) opening and insert and secure the flush-mount housing. 2. After securing the housing, insert the monitor into the housing. Do Not Apply Pressure Directly to the LCD Monitor’s Screen. Utilize the outer edges to gently push the monitor into the housing until it snaps into place. Mounting Screws (Not Supplied) 3 Cut a 7 /8
Summary of the content on the page No. 11
Maintenance Although this monitor requires little care, you can still maintain its condition and performance by following these steps: • Keep the system away from excessive moisture, extreme heat or cold, and magnetic fields. • Occasionally clean the monitor screen with damp soft cloth. Should you experience any problem with the system please refer to the troubleshooting guide prior to returning your system for repair. Note 1: The user should not attempt to service the unit beyond that described
Summary of the content on the page No. 12
Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within one year from the date of sale to you, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product. This warranty and Magnadyne
