Rosen Entertainment Systems EM-1 user manual

Summary of the content on the page No. 1

38114 Rosen_cover.p65 1 8/3/01, 10:26 AM

Summary of the content on the page No. 2

Table of Contents 7 Specifications • Power Supply: DC12V +/- 5% Section Page  Power Supply Consumption: 100VAC-240VAC@ 1 Amp 1. Quick Reference Guide 1-2  Input: TV/CATV NTSC system, F type connector, Composite NTSC Video/Stereo Audio. 2. About your EM1 System 3  Output: 6.8” TFT Monitor  Stereo speaker output 0.5W(max) 3. Installation of your EM1 4-9 Distortion <10%@1KHZ (Volume maximum)  Operating temperature: 0°C~ +40°C 4. Using the Remote Control 10-11  Storage temperature: -40°C~ +

Summary of the content on the page No. 3

6 Trouble Shooting Your EM1 3 Installing Your EM1 This section will give a brief trouble shooting guide Please call Rosen Technical Support at 888-883-2790 for further information or technical support.  NO AUDIO - Check volume level. Check MUTE button. Check volume level on AUX. input. Check that correct interface cable is used  NO VIDEO - Check desired source is selected by pressing the MODE button. Check Brightness, Color and Contrast settings. Check AUX input Check Cable in for proper

Summary of the content on the page No. 4

5 Using Auxiliary Sources 1 EM1 Quick Reference Guide 3 Installing Your EM1 Remote Sensor Lens Your EM1 has the capability to have one auxiliary source plugged into it at a time. This may include DVD players, closed circuit TV, camcorders, video game systems and other NTSC (RCA type) inputs. Plug in your V (video) L (left audio) and R (right audio) RCA cables into the appropriate spot on the EM1 Tuner Speakers module. Plug in your auxiliary source power supply (unless the auxiliary i

Summary of the content on the page No. 5

4 Using the Remote Control 1 EM1 Quick Reference Guide 3 Installing Your EM1 Master Remote Operations User Remote controller The User remote is used for The master remote has all the features of the user remote day to day operation. It has plus five set up features. These features include: basic functions such as:  CONTRAST - Contrast has a scale from 0 (lowest  Volume Up and Down setting) to 16 (highest setting). The factory default is and Mute set at 8. To change the contrast push

Summary of the content on the page No. 6

4 Using the Remote Control 3 Installing Your EM1 2 About your EM1 3 Installing Your EM1 Your Rosen EM1 has the following components: Client Remote Operations The client remote has five basic functions. These  Fully adjustable 6.8” LCD, Infrared remote functions include: receiver, with audio speakers. Figure 1  MODE - This button selects the different types of  Cable ready EM-1 Tuner Module with auxiliary video sources. The source is indicated in the upper inputs.

Summary of the content on the page No. 7

3 Installing Your EM1 3 Installing Your EM1 EM-1 FPD A. Getting Started  Locate the desired placement of components to ensure a proper fit. Make sure the monitor has enough room for desired movement. Warning: Excessive moisture and condensation will damage unit. Be sure your chosen location for the interface box and monitor are in a clean dry area.  Ensure there is a wall plug within 4’ of desired Tuner module location before mounting any * 15 ft. Interface Cable components.  The Tuner mod

Summary of the content on the page No. 8

3 Inst 3 Installing alling Y Your EM1 our EM1 3 Installing Your EM1 B. Mounting of Components (Cont.)  Plug pigtail from monitor into interface cable in J-Box. Table Top or Under Counter Mount  Coil excess (service loop) wire in J-box and mount  Use the Mounting base plate as a template to mark monitor using supplied screws. mounting holes  Replace base cover.  Mount base plate to monitor using 6-32 screws provided  Test for stability and desired range of motion. Note : Mounting plate is

Summary of the content on the page No. 9

3 Installing Your EM1 3 Installing Your EM1 C. Mounting on Wall to J-Box  The EM1 is designed to mount in a round 3 1/2” 2 1 electrical junction box (J-Box) like the one shown below. J-Box Note : Mounting plate is 3 only used when Note: you want to A J-box may be purchased at any local surface mount hardware store your EM1  Make sure J-Box is secure before mounting Interface cable monitor assembly. 4  Route 15ft interface cable from j-box to desired Tuner module location.  Use a 1/8” standa