Summary of the content on the page No. 1
30" (76.2 CM) AND 36" (91.4 CM)
SLIDE-OUT RANGE HOOD
Installation Instructions and Use & Care Guide
HOTTE D'ASPIRATION AVEC MODULE DE
COMMANDE EXTRACTIBLE DE 30" (76,2 CM)
ET 36" (91,4 CM)
Instructions d’installation et Guide d’utilisation et d’entretien
Table of Contents/Table des matières.............................................................................2
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONLY.
IMPORTANT : LIRE ET CONSERVER CES
Summary of the content on the page No. 2
TABLE OF CONTENTS TABLE DES MATIÈRES RANGE HOOD SAFETY .................................................................3 SÉCURITÉ DE LA HOTTE D’ASPIRATION ................................19 INSTALLATION REQUIREMENTS ................................................4 EXIGENCES D’INSTALLATION...................................................21 Tools and Parts ............................................................................4 Outils et composants ........................................
Summary of the content on the page No. 3
RANGE HOOD SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you don't immediately
Summary of the content on the page No. 4
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. IMPORTANT: Observe all governing codes and ordinances. Read and follow the instructions provided with any tools listed Have a qualified technician install the range hood. It is the here. installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating Tools needed plate is located behind the left
Summary of the content on the page No. 5
Product Dimensions 30" (76.2 cm) model: 8" (20.3 cm) FRONT OF 36" (91.4 cm) model: 11" (27.9 cm) RANGE HOOD 4³⁄₈" (11.1 cm) 3¹⁄₄" (8.3 cm) 30" (76.2 cm) model: 26" (66.0 cm) 36" (91.4 cm) model: 32" (81.3 cm) 10" (25.4 cm) ³⁄₈" (9.5 mm) 2³⁄₈" (6.0 cm) 2" 30" (76.2 cm) model: 13" (33.0 cm) 9¹⁄₂" (5.1 cm) (24.1 cm) 36" (91.4 cm) model: 16" (40.6 cm) 8" ¹⁄₄" (20.3 cm) (6.4 mm) Shelf extends 7" (17.8 cm) 1¹⁄₄" 1⁵⁄₈" (31.8 mm) (41.3 mm) 1" (25.4 mm) ⁵⁄₈" to 2¹⁄₈" BACK OF
Summary of the content on the page No. 6
Makeup air Example vent system 3¹⁄₄" x 10" (8.3 cm x 25 cm) Local building codes may require the use of makeup air systems when using ventilation systems with greater than specified CFM Wall cap of air movement. The specified CFM varies from locale to locale. 90˚ elbow Consult your HVAC professional for specific requirements in your 6 ft (1.8 m) area. Venting Methods This range hood is factory set for venting through the roof or 3 ft (0.93 m) through the wall. The vent system needed for ins
Summary of the content on the page No. 7
Electrical Requirements ■ A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is For GZ or IH model series: required. WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device. ■ If the house has aluminum wiring, follow the procedure below: For KWVU model series: This fan is suitable for use with solid state speed controls. 1. Connect a section of solid copper wire to the pigtail leads. Observe all governing codes and ord
Summary of the content on the page No. 8
3. If the cabinet bottom is recessed above a support frame, Transfer measurement A and B to the cabinet back wall. wood filler strips need to be installed on the right and left Measure from the underside of the cabinet or wood filler sides of the cutout to provide sides of clearance for the strips, if used. Mark the cutout as shown. Use a saber saw or sliding screen. Wood filler strips should be flush with or keyhole saw to cut a rectangular opening for the vent. recessed ¹⁄₁₆" to ¹⁄₈" (1.6
Summary of the content on the page No. 9
5. Install the vent system according to the method needed. Use 8. Measure the thickness of the cabinet floor, including the filler caulking to seal the exterior wall or roof opening. strips, if used. If the thickness is less than ⁵⁄₈" (15.9 mm), install wood filler strips that are a minimum length of 6. Determine wiring knockout. 5" (12.7 cm) onto the cabinet floor. The mounting bracket To wire through the top wiring knockout: adjusts from ⁵⁄₈" (15.9 mm) to 2¹⁄₈" (54.0 mm) for the wood fill
Summary of the content on the page No. 10
11. Remove the top or rear knockout from the wiring opening, depending on which one will be used. Install a UL listed or Install Range Hood CSA approved ½" strain relief. 1. Using 2 or more people, lift the range hood into its final position and feed the home power supply cable through the A wiring opening in the range hood. 2. Check that the mounting brackets overlap the cabinet bottom or wood filler strips. 3. Center the range hood. A B C D A. Wiring knockouts E 12. Place the range hood
Summary of the content on the page No. 11
5. Align the range hood front panel with the cabinet. Slide the screen forward. Locate the 2 screws on each side and turn WARNING them counterclockwise to loosen the screws. Adjust the front of the vent vertically, ³⁄₈" (9.5 mm) up or down, or horizontally, ³⁄₄" (19 mm) front to back, until the front is flush with the cabinet. Tighten the screws. If it is necessary to adjust the given dimensions, lower and add or remove the filler strips or redrill mounting holes. A Fire Hazard Electric
Summary of the content on the page No. 12
Optional Front Trim Kits Front trim kits for matching the front panel to your range or cooktop color are available from your dealer. Install Front Trim Kit For ordering information see the “Assistance or Service” section. 1. Pull out on the range hood screen for easier access to the screws. For 30" (76.2 cm) model series 2. Remove the 3 mounting screws directly behind the front KWVU205: panel, and remove the front panel from the range hood Part No. 4360201 (white) screen. Part No. 4360203 (b
Summary of the content on the page No. 13
GZ and IH Model Series 4. Move the fan switch to 0 or close the glass screen. B A The fan will shut off when the screen is about 2" (5.1 cm) from C the closed position. When the screen is opened, the fan will operate at the last settings. Operating the Light D 1. Open the range hood screen about 1" (2.5 cm). A. Light switch 2. Move the light switch to the 1 position. B. Fan switch The light will be on each time the screen is opened. The light C. Indicator light can be used for a night light
Summary of the content on the page No. 14
6. Place charcoal filter into opening, resting the back of the filter on tabs “A,” then clip filter tabs “C” into slots “B.” Replacing the Bulb Turn off the range hood and allow the bulb to cool. Use a 15-watt fluorescent bulb with 30" (76.2 cm) unit and 18- watt bulb with 36" (91.4 cm) unit. 1. Disconnect power. 2. Remove the screws above the light cover and set them aside. B 3. Pull the light cover forward slightly and then downward to C remove the cover. 4. Replace the light bulb. A 5. Lift
Summary of the content on the page No. 15
WIRING DIAGRAMS KWVU Model Series WIRING BOX W G G 8 BS/28K–A120 BK LIGHT 120 VAC LINE IN 7F u BALLAST 6 K2 TRANS. 5 H K1 BK 1 4 FLUORESCENT 3 LAMP 2 FL S H K L W H FAN R LIGHT FAN R ON-OFF OFF 12 3 FLAT CABLE CONNECTOR PUSH BUTTON PANEL 15 CONNECTOR V V CONTROL BOARD OR BU BK BR V GY W W BK
Summary of the content on the page No. 16
GZ and IH Model Series BK OR BU GY 8 BS/28K–A120 BR V W LP 7 uF W BK LIGHT BK BK R R S FAN 120 VAC BK WBK LINE IN FLUORESCENT LAMP 16 WIRING BOX BK GG W BALLAST TRANS.
Summary of the content on the page No. 17
ASSISTANCE OR SERVICE When calling for assistance or service, please know the purchase For further assistance date and the complete model and serial number of your If you need further assistance, you can write to Whirlpool appliance. This information will help us to better respond to your Corporation with any questions or concerns at: request. Whirlpool Brand Home Appliances Customer eXperience Center If you need replacement parts 553 Benson Road If you need to order replacement parts, we re
Summary of the content on the page No. 18
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company. This limited warranty is valid o
Summary of the content on the page No. 19
SÉCURITÉ DE LA HOTTE D’ASPIRATION Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres. Tous les messages de sécurité suivront le symbole d’alerte
Summary of the content on the page No. 20
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ AVERTISSEMENT : POUR MINIMISER LE RISQUE AVERTISSEMENT : POUR RÉDUIRE LE RISQUE D'UN FEU DE GRAISSE SUR LA CUISINIÈRE : D'INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES CORPORELS, RESPECTER LES INSTRUCTIONS ■ Ne jamais laisser un élément de surface fonctionner à SUIVANTES : puissance de chauffage maximale sans surveillance. Un renversement/débordement de matière graisseuse pourrait ■ Utiliser cet appareil uniquement dans les applications provoquer une infla
