Summary of the content on the page No. 1
AG-168V SIP GATEWAY User Manual (V1.42)
AG-168V SIP GATEWAY User Manual
AG-168V SIP GATEWAY Appearance Introduction:...................................................... 2
Features ................................................................................................................................ 2
Function Keys of AG-168V SIP GATEWAY Introduction ........................................... 3
Standard and Protocol........................................................
Summary of the content on the page No. 2
AG-168V SIP GATEWAY User Manual (V1.42) Gateway Front Illustration: Features 2
Summary of the content on the page No. 3
AG-168V SIP GATEWAY User Manual (V1.42) Indicator light and function Indicator Function Indicator Function light light Power Power on ,indicating power Status Registered off, not registered flash Tel communicaing flash, Buttons Function voice indicating “local ip ” , refer to “GATEWAY Keypad set” chaptor set different way of internet connection, refer to “GATEWAY Keypad set” chaptor IP Set static ip address when in “static mode ” enable AG-168V into “setting mode ”, refer
Summary of the content on the page No. 4
AG-168V SIP GATEWAY User Manual (V1.42) Dynamic voice jitter buffer G.168/165 compliant 16ms echo cancellation Tone generation and Local DTMF re-generation according with ITU-T E.164 dial plan and customized dial rules 100 entries for quick dial Voice prompt Hotline Standard and Protocol Gateway supports following standard and protocol: IEEE 802.3 /802.3 u 10 Base T / 100Base TX Major G.7XX and gsm610 audio codec SIP RFC3261 TCP/IP: Internet transfer and
Summary of the content on the page No. 5
AG-168V SIP GATEWAY User Manual (V1.42) Network interface:1 RJ-45 Ethernet Connectors FXS:1 RJ-11 For Tel Line:1 RJ-11 For PSTN Size 150 x 110 x 28 mm (L x W x H) Installation: 1 Connecting to network: connecting one side of the cable to the lan port of AG-168V, the other side to PBX or HUB or ADSL and Cable Modem’s lan port.. 2 Connecting to phone: Insert one side of RJ11 line to the Tel port of AG-168V , the other side to the phones’ interface. Connecting the Line’s po
Summary of the content on the page No. 6
AG-168V SIP GATEWAY User Manual (V1.42) Configuration Two different ways can be used to configure AG-168V H323 phone: phone web browser, Telnet commands on computer. Phone Keypad setup Using the keyboard of the normal phone connecting to AG-168V FXS port and the “IP key” , which can preset and enter into “Setting mode” , operation as below: Operation Function 1 with handset of FXS port ‘s phone hung, press IP ,voice promt “local ip” IP 2 with handset
Summary of the content on the page No. 7
AG-168V SIP GATEWAY User Manual (V1.42) x input the ip address xxx.xxxx.xxx.xxx, press “ip ” button . Using the button of * for , + IP Configured by WEB Double click icon to open the IE browser. Input the IP address of the GATEWAY into address bar ( ), and then input password of the GATEWAY into the following page. Default password 1234 is ordinary password and super password is 12345678. With Debug set 0[disable], please input super password; while Debug is not set as 0[disa
Summary of the content on the page No. 8
AG-168V SIP GATEWAY User Manual (V1.42) Fig 3.1 Http Setting Network Setting Fig 3.2 Network Setting iptype: Set how IP GATEWAY gets relevant network parameters by selecting corresponding item from drop down list. static ip: Select this item to authorize users set IP address, subnet mask and router IP address of IP GATEWAY manually. dhcp: Select this item to enable DHCP mode. With this system, your LAN or router automatically assigns all the required network parameters to
Summary of the content on the page No. 9
AG-168V SIP GATEWAY User Manual (V1.42) relevant network parameters auto. Then please fill ID and pin into ppp id and ppppin fields. ppp id: With pppoe or modem selected in iptype drop down list, please enter the user name here. ppp pin: With pppoe or modem selected in iptype drop down list, please enter the password here. local ip: With static ip selected in iptype drop down list, please enter IP address of IP GATEWAY here. subnet mask: With static ip selected in iptype drop d
Summary of the content on the page No. 10
AG-168V SIP GATEWAY User Manual (V1.42) Protocol Setting Fig 3.3 Protocol Setting use service: Enable/disable service by checking/clearing this box. To make calls through gatekeeper, please check this box; otherwise, GATEWAY can only make IP-to IP calls or calls through gateway. register ttl: IP phone will send a keep-alive registration message to SIP proxy server every “register ttl” seconds. The minimum value is 10, maximum value is 65535. Default is 60. service type:
Summary of the content on the page No. 11
AG-168V SIP GATEWAY User Manual (V1.42) kaimen use kaimen’s system mediaring: use mediaring’s system italkbb: use italkbb’s system stanaphone: use stanaphone’s system net2phone: use net2phone’s system fwd: use fwd(freeworlddialup) system ipphonex: use ipphonex’s system sipphone: use siphone’s system ngtel: use ngtel’s system ayctel: use AycTe’s system SIP proxy: when user service write SIP Proxy Server URI. Domain/realm : set SIP serve address domai
Summary of the content on the page No. 12
AG-168V SIP GATEWAY User Manual (V1.42) every “nat ttl” seconds to keep the port mapping on the NAT device alive. “nat ttl” is an integer between 10 and 65535 .default value is 20. phone number: set local ID . account: set aaa@bbb format account register. pin: set password. register port: The local UDP port registered with server to accept incoming handshaking messages. Default is 5060 rtp port : RTP port is the port transferring and receiving voice packets using UDP protoc
Summary of the content on the page No. 13
AG-168V SIP GATEWAY User Manual (V1.42) recommended way with SIP protocol used. dtmf: Set DTMF signal sending way by selecting control string, inband audio, signal keypad or rfc 2833 ,sip infofrom list box. dtmf payload: set use RTP send DTMF’s RTP the value range is 96-101 register ttl : IP GATEWAY will send a keep-alive registration message to SIP gatekeeper every “register ttl” seconds. The value range is 10-65535. Default is 60. Super password : Set super password. Def
Summary of the content on the page No. 14
AG-168V SIP GATEWAY User Manual (V1.42) Fig 3.4 phone Setting use dialplan: Set whether use dial plan or use dial number by selecting the corresponding item in drop down list. disable: Do not use dial plan or dial number by selecting this item. enable: Use dial plan by selecting this item. dialnum: Use dial number by selecting this item. With this item selected, please enter the dial prefix into dial number field. prefix: Use 179XX service by selecting this item. Hotline:
Summary of the content on the page No. 15
AG-168V SIP GATEWAY User Manual (V1.42) ddd prefix: With enable or dialnum selected in use dialplan drop down list, set long distance call prefix according to E.164 dial rule, such as 0. inner line: Enable/disable innerline call by selecting corresponding items from dropdown list. disable: Disable call innerline by selecting this item. enable: enable call innerline by selecting this item. omit prefix Enable , ingnore the number of the inner line prefix , cooperated with speci
Summary of the content on the page No. 16
AG-168V SIP GATEWAY User Manual (V1.42) forwarded calls GATEWAY number into fwd number field. fwd busy: Forward calls if busy by checking this box. Please enter receiving forwarded calls GATEWAY number into fwd number field. answer: Enter a number from 0 through 60 to set the entries of the seconds before the GATEWAY answer the call auto or forward the calls. handset in: Drag the slider to adjust the volume of handset input. Drag it to the left to reduce the volume; while drag it
Summary of the content on the page No. 17
AG-168V SIP GATEWAY User Manual (V1.42) g729 g7231 g711u g711a and gsm. codec3: Set the priority 3of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. codec4: Set the priority 4of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. codec5: Set the priority 5of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is 6.3kbps
Summary of the content on the page No. 18
AG-168V SIP GATEWAY User Manual (V1.42) Phonenumber: check phonenumber auto upgrade. upgrade addr: Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this field. nts ip: Fill IP address of time server here. use daylight: Enable/disable daylight. timezone: Select correct time zone in list box. When debug set as 0[disable], if input ordinary password (default one is 1234), then following page will pop up after clicking . And only those par
Summary of the content on the page No. 19
AG-168V SIP GATEWAY User Manual (V1.42) button to confirm the modification. phone Book: Click this button to open the speed dial settings page. Please refer to Fig 3.7. In this page, you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name. For example, input Jack in Name field following 001, and then input 5989426454 into GATEWAY number field. Then Jack’s number 5989426454 is saved in GATEWAY book. T
Summary of the content on the page No. 20
AG-168V SIP GATEWAY User Manual (V1.42) connecting with the GATEWAY or at the same segment of the GATEWAY, double click icon to open the PalmTool. The index page of PalmTool will popup. a) Input the IP address of the GATEWAY into Local IP field (such as 192.168.1.100), and then click “GATEWAY Settings” button. From Version1.24, use PalmTool to set the IP GATEWAY, please set debug as output or output all firstly, or PalmTool cannot connect IP GATEWAY. The parameters of PalmTool is same a
