Summary of the content on the page No. 1
Z100 / Z300 Z500
Z700
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Summary of the content on the page No. 2
Table of Contents Product Registration………………………………………………………….. 2 Important Safety Instructions………………………………………………… 3 Important Electrical Information…………………..……………………………4 Important Operation Instructions…………..…………………………………..4 Assembly Instructions………………………………..…………………………5 Transport…………………………………………………………………………8 Operation of Your New Elliptical…………………..…………………………...9 Manufacturer’s Limited Warranty…………………………………..………….13 ATTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONL
Summary of the content on the page No. 3
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealersh
Summary of the content on the page No. 4
Important Safety Instructions WARNING - Read all instructions before using this appliance. ■ Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet and elliptical may result. ■ Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. ■ Keep hands away from all moving parts. ■ Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly
Summary of the content on the page No. 5
Important Electrical Information WARNING! ● NEVER remove any cover without first disconnecting AC power supply. ● If voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. ● NEVER expose this elliptical to rain or moisture. This product is NOT designed for use outdoors, ne
Summary of the content on the page No. 6
Assembly Instructions ASSEMBLY PACK CHECK LIST ■ ■ M8x20mm Button Head Socket Screw (4pcs) ■ ■ ■ ■ ■ ■ M8x15mm Hex Head Screw (6pcs) ■ ■ ■ ■ M8x50mm Button Head Socket Screw (2pcs) ■ ■ ■ ■ M8x45mm Button Head Socket Screw (4pcs) ■ ■ ■ ■ M4x30mm Self Tapping Screw (4pcs) ■ ■ ■ ■ 5/16” x 19 x 1.5T Curve Washer (6pcs) ■ ■ ■ ■ 5/16”x23x1.5T Flat Washer (8pcs) ■ ■ M8 Nylon Nut (2pcs) ■ ■ ■ ■ ■ ■ 13/14mm N Wrench (1pc) ■ ■ M5 Allen Wrench (1pc) ■ ■ ■ ■ ■ ■ Screwdriver(1pc) A
Summary of the content on the page No. 7
■ ■ ■ ■ STEP 5 1. Install the Handle Bar Cover Front onto the Front Post with 1pc of M5x15m/m Button Head Socket Screws. (As shown in Fig. 12) 2. Take the Fix Handle Bar through the Hand Bar Cover Front and install it onto plate with 2pcs of M8x20m/m Button Head Socket Screws. (As shown in Fig. 13) 3. Install the Handle Bar Cover Back onto the Front Post with 1pc of M5x15m/m Button Head Socket Screws. (As shown in Fig. 14) ■ ■ ■ ■ STEP 6 Install the Lower Swing Bar into the Le
Summary of the content on the page No. 8
■ ■ ■ ■ PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED. Assembly Photos 7 ZE20
Summary of the content on the page No. 9
8 ZE20
Summary of the content on the page No. 10
Transport The elliptical is equipped with two transport wheels which are engaged when rear of ZE20 is lifted. 9 ZE20
Summary of the content on the page No. 11
Operation of Your Elliptical Getting familiar with the control panel ■ Console 10 ZE20
Summary of the content on the page No. 12
Power up The elliptical is supplied with a wall mount power supply. When power is connected to the elliptical, the console will automatically power up. If there is no input to the console for 4 minutes the console will go to stand-by mode. In stand-by mode the console display will turn off. All work out data will be saved in stand-by mode. When initially powered on the large display will light. The data windows will show zero and the program choices will be blinking in the large window. I
Summary of the content on the page No. 13
Preset Programs There are 12 preset programs to choose from. After power up, or reset, press the Up/Down keys to highlight the Program icon. Press the Mode key to enter the program mode. The display will show P1, for two seconds, then change to the P1 program profile. You may keep pressing the Up/Down keys to scroll through the 12 programs. When you see a program you want, press the Mode key to enter. At this point you may press start to begin the program with the default settings or you m
Summary of the content on the page No. 14
If you want to choose to work at 75% - for example - then use the Up/Down arrows to highlight 75% and press mode. Now the Time window will be blinking and you can program it and other data the same as other programs. If you want to set your own custom Target HR then use the Up/Down arrow to highlight THR and press mode. The Pulse window will now be blinking. Use the Up/Down arrows to set your own Target HR and press Mode to continue. Recovery Used to measure how fast your heart rate (HR
Summary of the content on the page No. 15
Manufacturer’s Limited Warranty Effective October 15, 2004 ELLIPTICAL WARRANTY Spirit Manufacturing Inc. warrants all its elliptical parts for a period of 2 years from the date of retail sale, as determined by sale receipt, or eighteen (18) months from the original factory shipping date, whichever comes first. Spirit’s responsibilities include providing new or remanufactured parts, at Spirit’s option, and technical support to our independent dealers and servicing organizations. In
