Summary of the content on the page No. 1
CS-2014TW2 Super Page V™
2-Way AM/FM LCD Paging Alarm & Remote Engine Starting System
OPERATION INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of the SuperPage V™ by Crimestopper Security Products Inc. This booklet
contains the information necessary for operating your system. If any questions arise, contact your installation dealer or
Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These features m
Summary of the content on the page No. 2
TABLE OF CONTENTS Operation Cautions & Warnings……..…………..……………………………………………………………………2 Transceiver / Pager-Remote……….....…………..……………………………………………………………………3 CS-416TW Sidekick Remote Control…………………….…………………………………………………..…...…..4 Operating Instructions - Alarm……………………………………………………….………..……………..……..5-8 Remote Engine Control………………………...……………………………………………….…….………...….9-12 Anti-Carjack Protection...……………………………………….………….……..………………..………..………..13 LED Diagnostics………………..………………………………………………
Summary of the content on the page No. 3
TRANSCEIVER / PAGER-REMOTE PAGER / REMOTE TRANSCEIVER: The hand-held remote transceiver is used to send and FIXED receive information from the vehicle. The Control Module ANTENNA transmits High Frequency AM/FM signals from the vehicle #2 DISARM to your over long distances. Your range will vary depending #1 ARM UNLOCK LOCK on location, terrain, and local RF noise/interference. This system is not guaranteed to page you if you are behind concrete walls, underground, in a large
Summary of the content on the page No. 4
CS-416TW SIDEKICK REMOTE The CS-416TW 1-Way sidekick remote adds flexibility to your CS-2014TW2. You can have the convenience of operating your system without needing to carry the larger pager remote. The Sidekick remote has #2 less range and offers all of the same operation features except for page-back confirmation. UNLOCK/ BUTTON 1(Lock Symbol): DISARM • Press and release to Arm/Lock system. #1 #5 • Press and Hold for more than 3 seconds to LOCK/ activate “Panic” feature.
Summary of the content on the page No. 5
OPERATING INSTRUCTIONS - ALARM Active Arming / Locking: Press button #1 (Lock symbol) on the transceiver. The System will arm emit one siren chirp, one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. LCD Pager will beep once while displaying a Locking symbol. After a short delay to allow the vehicle and electronics to settle, the system will be completely armed. Disarming: / Unlocking Press button #2
Summary of the content on the page No. 6
OPERATING INSTRUCTIONS - ALARM Disarming While Tripped (Triggered): Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system. Selective Silent Arming/Disarming: To Arm or Disarm the system without siren chirps, press and release both Buttons #2 (Unlock) and #4 (Start) at the same time. System will Arm or Disarm without
Summary of the content on the page No. 7
OPERATING INSTRUCTIONS - ALARM Pre-Warning Shock Protection The Pre-warning (warn-away) feature will activate when a low-level shock or vibration detected by the system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any further tampering with the vehicle. The pager/remote will vibrate and beep (1). Passive Arming Mode: (Programmable) Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the last door
Summary of the content on the page No. 8
OPERATING INSTRUCTIONS - ALARM Emergency Override (Disarm) If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you can repair/replace the remote. Valet mode also prevents Passive Arming. Valet Mode (Enter ma
Summary of the content on the page No. 9
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START 1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation. (Chirps can be programmed on or off-See installation manual.) 2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on. 3) After a few seconds, Starter Motor engages, Parking lights and Accessory circuits turn off while cranking. 4) Engine Starts and Runs. Parking Lights and Accesso
Summary of the content on the page No. 10
REMOTE ENGINE CONTROL UNSUCCESSFUL REMOTE START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then nd rd attempts to restart the engine a 2 and 3 time. For hard starting engines, the unit will allow a starter crank time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13 seconds to help prevent damage to the starter from over cranking. nd rd 1) If engine starts on
Summary of the content on the page No. 11
REMOTE ENGINE CONTROL IDLE DOWN MODE (TAKE-OVER OPERATION) This mode allows the unit to take over operation of your idling, parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time, until you return, or until the remote start button is pressed. Example: You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine runnin
Summary of the content on the page No. 12
REMOTE ENGINE CONTROL TIMED SELF START MODE This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine or fluid freeze-up is a concern. !!THE VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA!! TIMED SELF-START MODE – EXITING THE VEHICLE: 1) Have engine running with the Key, then press the Start button on the transmitter. 2) Within 10 seconds press the valet/pr
Summary of the content on the page No. 13
ANTI CARJACK PROTECTION REMOTE OPERATED CARJACK PROTECTION This feature provides Active Carjack protection through the remote control. When the Ignition is on (vehicle is running), press and hold the #1 LOCK Button and #3 TRUNK Button for 2 seconds. The parking lights will flash 2 times and the LED will begin to flash rapidly to confirm the beginning of a Carjack countdown. 30 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning i
Summary of the content on the page No. 14
LED DIAGNOSTICS The CS-2014FM system includes disarm diagnostics, through the RED LED light, that will help in determining what caused the last trigger of the alarm system. This is a valuable tool in determining how the vehicle was tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to correct the problem. When the system is disarmed with the remote you will hear the normal 2 chirps, then 4 quick chirps that indicate the alarm wa
Summary of the content on the page No. 15
TRANSCEIVER / REMOTE CONTROL PROGRAMMING IGN OFF WAIT FOR (BLUE WIRE GROUNDED) 4 FLASHES PRESS 4X's 2-WAY SYSTEMS & "SideKick" REMOTES IGN FLASH 2, 3, or 4 X's OFF LOCK & COMPLETE UNLOCK PRESS TOGETHER 15
Summary of the content on the page No. 16
2 VEHICLE OPERATION 2 VEHICLE CONTROL Your CS-2014FM remotes have the ability to control a second vehicle with a Crimestopper CS-2014FM system installed. To set up the 2-Vehicle operation you must first program your remotes to VEHICLE #2 CONTROL: Vehicle #2. Follow the “Transmitter FIXED Programming” steps (Pg. 14) at the ANTENNA second vehicle and learn YOUR remote, "Sidekick" along with vehicle #2’s existing remotes. Remote LED Flashes 2-VEHCLE OPERATION NOTES: (1) Yo
Summary of the content on the page No. 17
TROUBLESHOOTING FAQ’s: “BEFORE YOU CALL SECTION” Before calling your dealer or Crimestopper, read the following section for tips that may remedy or explain your problem. RANGE QUESTIONS (2-Way Pager/Remote): Your CS-2014FM system uses FM High-Frequency signals to send/receive data between the pager and the vehicle and from the vehicle to the remote for state-of-the-art operation. 1) Under normal operation, the distance from the vehicle-paging-the-remote will be greater than that
Summary of the content on the page No. 18
TROUBLESHOOTING continued SYSTEM IS NOT SUCCESSFUL AT REMOTE STARTING DURING EXTREME COLD CONDITIONS: Please be aware that during sub-freezing conditions your remote starter may take more that one attempt to start, or it may not successfully start the vehicle after 3 attempts. During these conditions, the vehicle may not properly start even using the key; therefore trying to start the vehicle by remote would also be unsuccessful. MY SYSTEM DOES NOT RESPOND TO THE REMOTE CONTR
Summary of the content on the page No. 19
LOW BATTERY WARNING - LCD REMOTE Your 2-Way pager remote will warn you when the battery gets low. You will see a battery icon on the LCD screen when it is time to replace the AAA battery. To replace the battery: simply unlatch and slide open the battery door on the back of the 2-Way LCD remote. Carefully insert a new battery, using the outline on the bottom of the battery compartment as a guide. Your remote will beep 3 times when the battery is inserted correctly.
Summary of the content on the page No. 20
Crimestopper Security Products Inc. ONLINE TECHNICAL SUPPORT 1770 So. Tapo Street www.crimestopper.com/techweb03.html Simi Valley, CA 93063 (800) 998-6880 www.crimestopper.com email@crimestopper.com ©2005 Crimestopper Security Products
