Dacor IF42NBOL user manual

Summary of the content on the page No. 1

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS,
IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL
42” and 48” Wide PLANNING
Revised
1/6
Built-In Refrigerators
GUIDE
04/22/08
Oeningp Diensim Ons
◊ To avoid tipping during use, the solid soffit must be within 1”
(2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1” (2.5 cm) or one is not available, then the
refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the
rear wall studs 80” to 90” (203 cm

Summary of the content on the page No. 2

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide PLANNING Revised 2/6 Built-In Refrigerators GUIDE 04/22/08 e lectrcali r tsnemeriuqe Wrte a s y ulpp r tseriunqeem ◊ All installations must meet local plumbing code requirements. The electrical circuit must meet all local codes and ordinances. Recommended Grounding Method ◊ The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible A

Summary of the content on the page No. 3

Overlay Panel Backer Panel Door Overlay Panel Backer Panel Door Spacer Panel EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide PLANNING Revised 3/6 Built-In Refrigerators GUIDE 04/22/08 DOOr s Wgni Disnemi On NOTE: More clearance may be required if you are using overlay panels, custom handles or extended handles on a IF series The location must permit both doors to open to a minimum of model. 90°. Allow 4½” (11.4 cm) minimum space between the sid

Summary of the content on the page No. 4

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide PLANNING Revised 4/6 Built-In Refrigerators GUIDE 04/22/08 c stu Om p anlse an D Han Dsel - F42/ i F48 i s eries m ODels IMPORTANT: Custom overlay panels used with models IF42 and IF48 allow you Install the panels after moving the refrigerator into to blend the exterior of your refrigerator into the overall kitchen place. décor, and to use custom handles for additional design flexibility. The weig

Summary of the content on the page No. 5

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide PLANNING Revised 5/6 Built-In Refrigerators GUIDE 04/22/08 c ust Om s i De p sanel - F42/ i F i 48 Inset Installation Dimensions Custom side panels may be needed when not enough space is 1. Measure the distance from point A (as shown) to the back wall. available to have cabinets on both sides of the refrigerator or Add ¹⁄32” (0.8 mm) to this measurement to allow the side panel when the refrigerat

Summary of the content on the page No. 6

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide PLANNING Revised 6/6 Built-In Refrigerators GUIDE 04/22/08 c ust Om s i De p aelsn - eF42/eF48 Inset Installation Dimensions Custom side panels may be needed when not enough space is 1. Measure the distance from point A (as shown) to the back 7 available to have cabinets on both sides of the refrigerator or wall. Add ⁄32” (5.6 mm) to this measurement to allow the side when the refrigerator is pla