Summary of the content on the page No. 1
SERVI
INSTALLATION
United States
AND
SALES OFFICES
OPERATING INSTRUCTIONS
SALES CORP.
2320 Industrial Pkwy.
IN 46515
Phone 219 - -
SALES CORP.
14441 Bonelli
REFRIGERATOR FOR LP-GAS
C i ty of Industry, CA 91746
Phone 616 - -
SALES CORP.
AND
1625-A Rock Mountain Blvd.
Stone Mountain, GA 30083
Phone
ELECTRIC OPERATION.
SALES CORP.
7695 S.W. Hunz i ker
Portland, OR 97223
REFRIGERATOR
Phone 503-620-9510
SALES CORP.
RM360
2920 Avenue
Arlington, TX 76011
RM460
Phone 617-277-7211
SALES CORP.
Summary of the content on the page No. 2
REFRIGERATORS WlTH PIEZ0 IGNITER Fig. la E DCB A Fig. 4a 2
Summary of the content on the page No. 3
REFRIGERATORS WlTH AUTOMATIC IGNITION E CB A Fig. 4b. 3
Summary of the content on the page No. 4
Fig. 5 Fig. 2 Clear blue colou r of flame Fig. 3 - Fig. 6 Gas equipment parts Burner tube 2 . Burner housing 3 . Burner jet 4. Feeler point (thermocouple) 5. Flame failure safety device 6 . Bypass screw 7 . Gas/Electric thermostat 6. Pressure test gage connection 9. Capillary tube for thermostat . Shut-off valve 11. Piezo igniter (lighter) . Firing tip . Hexagon nut Electric equipment parts 13 . Flexible cord . Change-over switch . 5 Terminal block, 12 V DC . Reigniter . Relay 22 . Cover 23. Te
Summary of the content on the page No. 5
ged a properly grounded three prong receptacle. INSTALLATION Do not cut or remove the grounding prong from this p!ug The cord should be routed t o d v a contac t the GENERAL INSTRUCTIONS burner cover. flue cover or other hot components The refrigerators outlined hereon have been design certified under ANS i! 21.19 Refrigerators by the American Gas Asso- Refrigerator models requiring 12 V DC ciation for installation in a mobile home or recreational vehicle supply and are approved by the Cana
Summary of the content on the page No. 6
SPECIAL HINTS The refrigerator must be installed in a substantial enclosure and must be level. A spirit level is supplied with each refrigera- tor and by placing it in the freezer compartment one can level the refrigerator both ways front to back and side to side. When installing the refrigerator in the enclosure care should be taken to ensure a complete sealing between the front frame of the refrigerator and the top, sides and bottom of the enclosure. For this purpose a length of sealing strip
Summary of the content on the page No. 7
CERTIFIED INSTALLATION Certified installations require one roof vent and one lower side vent or as optional one upper vent and one lower side vent. The two alternatives are provided for by using the different kits listed in the Appendix. For further information contact your dealer or distributor. METHODS OF INSTALLATION Condenser The methods of installation are shown in figures 9 and 10. It is essential that all maximum or minimum dimensions are strictly maintained as the performance of the refr
Summary of the content on the page No. 8
CLEARANCES Minimum clearances in inches to combustibl e G: Top 0 K: Side 0 L: Bottom 0 M: Rear 1 Clearance M between the part of the the wall behind the refrigerator Clearance N on top of the condenser is related to the minimum’ventilation height See Fig 11 and examples below Fig. 11 R Installation model di me ns ion s top of condenser to top of refrigerator Height Width Depth H e igh t Width Width A B C h W d H W D e RM 360 3 0 3/ 8 2 1 11 /1 6 6 22 1 /1 6
Summary of the content on the page No. 9
INSTRUCTIONS FOR USE HOW TO START THE REFRIGERATOR Flame Blow Out If trouble is encountered with the flame blowing out under Leveling specially windy conditions, try to avoid the wind blowing aga- In the boiler ammonia vapor is distilled from an ammonia-wa- inst the wall where vent outlets are located. If the trouble ter mixture and carried to the finned condenser, where it persists, set the thermostat to MAX. This later measure can off liquifies. The liquid flows to the evaporator, where it cre
Summary of the content on the page No. 10
Frozen Food Storage Compartment The Flame Failure Safety Device (Fig. 3) The ice trays should be placed in direct contact with the The feeler of th e couple shall reach in over two slots of freezer shelf for fastest ice making. Quick frozen soft fruits and the burner. To replace th e t couple proceed as follows: ice cream should be placed in the coldes t of the com- Remove the plastic cover 22 (Fig. 5). partment which is at the bottom of the aluminum liner or, in 2. Unscrew plug 20 and pull th
Summary of the content on the page No. 11
4. With a pair of pliers unfold the lug holding the lid of the WARNING boiler casing and open the lid If the refrigerator is used intermittently it should be checked 5. Remove some insulation wool so that the heater is acces- at least once a year. It is important to keep the appliance area clear and free Turn and lift the heater out of its pocket 6. from combustible materials, gasoline and other flammable Fit the new heater into the pocket and pull on the hose 7. vapors and liquides. Check the v
Summary of the content on the page No. 12
INSTRUCTIONS FOR MOUNTING THE DOOR PANEL The refrigerator is normally delivered without door panel(s). Before starting the mounting work check that the panel di- mensions are in compliance with those given in the table and read the instructions through. When mounting the panel, pro- ceed as follows. Remove the top decoration strip (2) with its two screws B. Insert one of the vertical edges of the panel into the groove of the door frame (3). C. Bend the panel gently so that the free side of the p
