Our goal is to provide you with a quick access to the content of the user manual for Electrolux 15. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Electrolux 15.
If looking through the Electrolux 15 user manual directly on this website is not convenient for you, there are two possible solutions:
Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Electrolux 15 but the selected pages only. paper.
Below you will find previews of the content of the user manuals presented on the following pages to Electrolux 15. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.
Use & Care Guide
Guia de Uso y Cuidado
Máquina de hielo
Guide d’utilisation et d’entretien
Machine à glaçons
241927600 November 2007
Finding Information 2 Please read and save this Keep a record for quick guide reference Thank you for choosing Electrolux, the new Whenever you call to request information or premium brand in home appliances. This Use & service, you will need to know your model number Care Guide is part of our commitment to customer and serial number. You can find this information on satisfaction and product quality throughout the the serial plate located on the inside wall of your service life of your
Finding Information 3 Table of Contents Finding Information .................................................2 Operation............................................................ 14 Please read and save this guide ..............................................2 Normal Operation .................................................................14 Keep a record for quick reference ...........................................2 Ice Cube Thickness .....................................................
Safety 4 Important Safety Instructions Safety Precautions WARNING Do not attempt to install or operate your unit until you have • Never attempt to repair or perform read the safety precautions in this manual. Safety items maintenance on the unit until the throughout this manual are labeled with a Danger, Warning electricity has been disconnected. or Caution based on the risk type. • Altering, cutting of power cord, removal Definitions of power cord, removal of power plug, or di
Installation 5 Installation Dimensions 14-15/16” 24” (37.9) (61) 34-1/8” (86.7) FULL RETRACT 5” HEIGHT (12.7) WATER WATER VALVE DRAIN WATER 21-3/4” OUTLET (55.2) Installing the Drain • Drain lines must have a 1 inch drop per 48 CAUTION inches of run (1/4 inch per foot) and must not create traps. PLEASE READ all instructions completely before attempting to install or operate the unit. • The floor drain must be large enough to All ice makers require a connection to the accommodate
Installation 6 Connecting a Drain Pump If a gravity drain connection is not available, we strongly recommend the use of the Electrolux EIMP60 drain pump. The Electrolux EIMP60 drain pump is available through your Dealer, or direct from Electrolux with complete installation instructions. If a pump other than the Electrolux EIMP60 drain pump is to be used, it must meet the following specifications: • It must be UL listed and have a UL listed, 120 VAC, 3-wire grounded power cord. • It m
Site Preparation 7 7 The unit must be installed according to your Preparing the Site local codes and ordinances. IMPORTANT NOTE It is extremely important that the unit is level. If it The door of the unit may be mounted on either is not level, the ice mold will not fill evenly. This side of the cabinet (see REVERSING THE can cause a reduction in ice rate, uneven sized DOOR). All units require zero clearance when cubes or water spilling into the storage area installed flush
Water Supply Connection 8 Connecting the Water Supply CAUTION When connecting the water supply, follow these After completing the installation, turn on guidelines: the water and recheck water and drain connection for leaks. Apply additional • Review the local plumbing codes before you tightening if needed. Do NOT use thread install the unit. sealing compound or tape. • The water pressure should be between 30 and 120 psi. 4 Plug in the power cord. CAUTION 5 Gently pus
Leveling 9 Leveling the unit 1 Use a level to check the levelness of the ice maker from front to back and from side to side (see Figure 10). CHECK LEVEL Figure 10 2 If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 11). TURN FOOT TO ADJUST Figure 11 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level.
Door Reversal 10 Reversing the Door (some models) All Electrolux units may be left or right hand 2 Remove plastic screw plugs (3 top and 3 opening. The door opening is easily reversed by bottom) from new hinge location (see Figure moving the hinge hardware to the opposite side 14), and remove hinge pin hole plug in top of (see Figure 12). door (see Figure 15). Do not discard. SCREW PLUGS Figure 14 UL308 Hole Plug Figure 12 To reverse the door: 1 Remove top hinge screw pin from cabinet ®
Door Reversal 11 4 Remove the two door closer inserts from the 7 Holding door upright with top of door tilted existing bottom hinge and install as shown on forward, place hole of door pivot plate on the new bottom hinge (see Figure 17). bottom hinge screw pin (see Figure 19). Be sure that the bosses on the closers align with holes in hinge and hinge plate. Figure 17 Figure 19 DOOR CLOSER INSERTS BOSS BOSS UL312 CLRCO008 5 Remove existing bottom hinge (3 screws) and remount on opposite
Door Adjustment 12 4 If door edge opposite the hinges needs to Adjusting the Door move up, move plate toward outside of door. If door edge needs to move down, move Your door is aligned at the factory before shipment. plate toward inside of door (see Figure 22). Occasional re-adjustment may be necessary, Repeat until top edge of door is parallel with especially if an overlay panel is installed. The top of cabinet and tighten screws securely. following procedure will correct for up to 1/
Built-In Installation / Start-Up 13 LIGHT , Installing a Built-In DOWN BL AC K OUT MODE UP ARROW DISPL AY ARROW & OTHER FUNCTIONS POWER Your Electrolux product has been designed for either free-standing or built-in installation. When ICE built-in, your ice maker does not require additional air space for top, sides or rear. However, the front Figure 24 grille must NOT be obstructed. Blackout Mode (not Star-K certified) NOTE 1. Touch and hold the LIGHT button for ten To ease unit inst
Operation 14 • Cube “slabbing”: Electrolux clear ice Normal Operation makers produce a “slab” of ice that falls from the vertical mold, relying on gravity to break The ice maker is designed to make clear ice the ice bridges. Depending on the control from most water sources on a consistent basis. setting, and the fullness of the ice bucket, it Water is constantly circulated over the evaporator maybe necessary to tap the ice slab with the assembly. As the water freezes, gravity causes
Operation 15 Ice Cube Thickness Adjustment SAMPLE AREA Interval - As Required Ice thickness adjustments are made using the control panel as follows: LIGHT , DOWN BL AC K OUT MODE UP ARROW DISPL AY ARROW & OTHER FUNCTIONS POWER ICE ICE005 Figure 28 Figure 27 1. To enter the thickness adjustment mode: a. Touch and hold the UP ARROW button. b. Touch and release the DOWN ARROW button three times, then release the UP ARROW button. c. The display will switch to “0,” to confir
Maintenance 16 • If any surface discolors or rusting appears, Special Considerations clean it quickly with Bon-Ami or Barkeepers • For best performance, keep the unit out of Friend Cleanser and a non-abrasive cloth. direct sunlight. Always clean in the direction of the grain. • Turn the unit OFF and dispose of any ice Always finish this process with a high quality, cubes if the unit will not be used for 5 days all-in-one stainless steel cleaner/polish to or more. Prop door open to
Maintenance 17 Condenser Cleaning — Every Self Cleaning — Every 6 Months To maintain operational efficiency, clean the unit 3 Months every six months (depending on water conditions To maintain operational efficiency, clean the more or less frequent cleaning may be necessary). condenser every three months (depending on If the ice maker requires more frequent cleaning, environmental conditions, more or less frequent consult a qualified plumber to test the water quality cleaning may be nece
Maintenance 18 2 Remove all ice from the storage bin. 8 Reinstall inside front cover. 3. Remove inside front cover. (See figure 31.) 9 When the self-cleaning process stops (approximately 45 minutes) the unit will remain off for an additional 15 minutes. When the clean cycle is completed, the display will automatically switch back to set temperature and unit will run as normal operation. 10 Clean the storage bin. (See INTERIOR CLEANING). Sanatize the bin with a solution of 1 tablesp
Maintenance / Storage, Vacation and Moving 19 Inlet Screen Cleaning — Draining for non-use If the unit is to be stored, moved or not used for Every Year extended periods, it will be necessary to drain the The solenoid valve inlet screen must be cleaned at system of water. least once each year as follows: 1 Shut off the water at the water supply valve. WARNING Electrical Shock Hazard. Disconnect power 2 Pull the unit out to access the back panel. before servicing. Before operating
Troubleshooting 20 Before You call For Service If the unit appears to be malfunctioning, read through Normal Operation first. If the problem persists, check the Troubleshooting Guide. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem could be something very simple which can be solved without a service call. DANGER ELECTROCUTION HAZARD NEVER attempt to repair or perform maintenance on the unit until the main electrical power ha